Thermo Scientific 3721 Mode d'emploi

Model 815 (3721 and 3722)

Microprocessor Controlled Low Temperature Incubator

Operating and Maintenance Manual 3177879 Rev. H

Thermo ScientificThermo Scientific

Manual Number 3177879

H24342/IN-3866 11/08 Added specs and additional info for CSA ccs

G 24342 10/08 1900381 rear comp cvr (from 316126, 1900390 int back wall plate (from 316135) ccs

F 24609 5/08 3185173 to 130630, 3164634 to 3164636 ccs

E -- 6/05 manual number, manufacture location (36100114 [34001729)

D -- 12/04 Update for base model FFU2064DW1 (pages 18-20)

C -- 9/01 Removed dual fans, updated parts list (pages 18-20)

B -- 8/99 Update parts list for new kit #s (page 19)

A -- 6/99 Initial release

Rev ECR/ECN Date Description By

Preface

Low Temp Incubator i

Covered

Models Volume (cu. ft.) Voltage

3721 20 120

3722 20 230

Thermo Scientificii Low Temp Incubator Thermo Scientific

Preface

Important Read this instruction manual. Failure to read, understand and follow the instructions in this manual

may result in damage to the unit, injury to operating personnel, and poor equipment performance. ▲

Caution All internal adjustments and maintenance must be performed by qualified service personnel. ▲

Warning If the incubator is used in the manner specified in this operating manual, the protection provided by

the equipment design may be impaired. ▲

Material in this manual is for information purposes only. The contents and the product it describes are subject to

change without notice. Thermo Scientific makes no representations or warranties with respect to this manual. In

no event shall Thermo be held liable for any damages, direct or incidental, arising out of or related to the use of

this manual.

Thermo Scientific Low Temp Incubator iiiThermo Scientific

Preface

Important operating and/or maintenance instructions. Read the accompanying text carefully.

Potential electrical hazards. Only qualified persons should perform procedures associated with this

symbol.

Equipment being maintained or serviced must be turned off and locked off to prevent possible injury.

Hot surface(s) present which may cause burns to unprotected skin, or to materials which may be

damaged by elevated temperatures.

Marking of electrical and electronic equipment, which applies to electrical and electronic equipment

falling under the Directive 2002/96/EC (WEEE) and the equipment that has been put on the market

after 13 August 2005.

This product is required to comply with the European Union’s Waste Electrical & Electronic

Equipment (WEEE) Directive 2002/96/EC. It is marked with the WEEE symbol. Thermo Scientific

has contracted with one or more recycling/disposal companies in each EU Member State European

Country, and this product should be disposed of or recycled through them. Further information on

Thermo’s compliance with this directive, the recyclers in your country and information on Thermo

products will be available at www.thermo.com.

✔Always use the proper protective equipment (clothing, gloves, goggles, etc.)

✔Always dissipate extreme cold or heat and wear protective clothing.

✔Always follow good hygiene practices.

✔Each individual is responsible for his or her own safety.

Thermo Scientificiv Low Temp Incubator Thermo Scientific

Preface

Do You Need Information or Assistance on

Thermo Scientific Products?

If you do, please contact us 8:00 a.m. to 6:00 p.m. (Eastern Time) at:

1-740-373-4763 Direct

1-800-438-4851 Toll Free, U.S. and Canada

1-740-373-4189 FAX

http://www.thermo.com Internet Worldwide Web Home Page

Service E-Mail Address

Thermo Scientific

Controlled Environment Equipment

401 Millcreek Road, Box 649

Marietta, OH 45750

Our staff can provide information on pricing and give you quotations. We can

take your order and provide delivery information on major equipment items or make

arrangements to have your local sales representative contact you. Our products are listed on the

Internet and we can be contacted through our Internet home page.

Our staff can supply technical information about proper setup, operation or

troubleshooting of your equipment. We can fill your needs for spare or replacement parts or

provide you with on-site service. We can also provide you with a quotation on our Extended

Warranty for your Thermo Scientific products.

Whatever Thermo Scientific products you need or use, we will be happy to discuss your

applications. If you are experiencing technical problems, working together, we will help you

locate the problem and, chances are, correct it yourself...over the telephone without a service

call.

When more extensive service is necessary, we will assist you with direct factory trained

technicians or a qualified service organization for on-the-spot repair. If your service need is

covered by the warranty, we will arrange for the unit to be repaired at our expense and to your

satisfaction.

Regardless of your needs, our professional telephone technicians are available to assist you

Monday through Friday from 8:00 a.m. to 6:00 p.m. Eastern Time. Please contact us by

telephone or fax. If you wish to write, our mailing address is:

International customers, please contact your local Thermo Scientific distributor.

Sales Support

Service Support

service.led.marietta@thermofisher.com

Thermo Scientific Low Temp Incubator vThermo Scientific

Preface

Warranty Notes

Information You Should Know Before Requesting Warranty Service

•Locate the model and serial numbers. A serial tag is located on the unit itself.

• For equipment service or maintenance, or with technical or special application inquiries, contact Technical

Services at 1-800-438-4851 or 1-740-373-4763 (USA and Canada). Outside the USA, contact your local

distributor.

Repairs NOT Covered Under Warranty

• Calibration of control parameters. Nominal calibrations are performed at the factory; typically ±1°C for

temperature, ±1% for gases, and ±5% for humidity. Our service personnel can provide precise calibrations as

a billable service at your location. Calibration after a warranty repair is covered under the warranty.

• Damage resulting from use of improper quality water, chemicals or cleaning agents detrimental to

equipment materials.

• Service calls for improper installation or operating instructions. Corrections to any of the following

are billable services:

1) electrical service connection

2) tubing connections

3) gas regulators

4) gas tanks

5) unit leveling

6) room ventilation

7) adverse ambient temperature fluctuations

8) any repair external to the unit

• Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, or improper

installation.

• Repairs to parts or systems resulting from unauthorized unit modifications.

• Any labor costs other than that specified during the parts and labor warranty period, which may

include additional warranty on CO2sensors, blower motors, water jackets, etc.

Section 4

Section 5

Section 6

Section 8

Section 7

Low Temp Incubator viThermo Scientific

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Unpacking and Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Performance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Explanation of Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . .1-3

Explanation of Auxiliary Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

Instrumentation Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Operation and Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Symptoms and Possible Causes . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Possible Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

General Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

RS232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

Setting Up the Incubator for Communication . . . . . . . . . . . . . . . .6-2

Using the Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5

Setting up the Computer for Communication . . . . . . . . . . . . . . . .6-5

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2

Section 1

Section 2

Section 3

Low Temp Incubator 1-1Thermo Scientific

Section 1 Introduction

Your satisfaction and safety are important to Thermo and a complete

understanding of this unit is necessary to attain these objectives.

Warning As a routine laboratory precaution, always wear safety glasses

when working with this apparatus. ▲

This product is not intended, nor can it be used, as a sterile or patient

connected device. In addition, this apparatus is not designed for use in

Class I, II or III locations as defined by the National Electrical Code.

Save all packing material until unit is put into service. This merchandise

was carefully packed and thoroughly inspected before leaving our factory.

Responsibility for safe delivery was assumed by the carrier upon acceptance

of the shipment; therefore, claims for loss or damage sustained in transit

must be made upon the carrier by the recipient as follows:

1. Visible Loss or Damage: Note any external evidence of loss or damage

on the freight bill, or express receipt, and have it signed by the carrier's

agent. Failure to adequately describe such external evidence of loss or

damage may result in the carrier's refusing to honor your damage

claim. The form required to file such claim will be supplied by the

carrier.

2. Concealed Loss or Damage: Concealed loss or damage means loss or

damage which does not become apparent until the merchandise has

been unpacked and inspected. Should either occur, make a written

request for inspection by carrier's agent within fifteen (15) days of the

delivery date; then file a claim with the carrier since the damage is the

carrier's responsibility.

If you follow the above instructions carefully, we will guarantee our full

support of your claim to be compensated for loss or concealed damage.

Note Do not - for any reason - return this unit without first obtaining

authorization. In any correspondence to Thermo, please supply the

nameplate data, including catalog number and serial number. ▲

Unpacking and

Damage

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Thermo Scientific Équipement de laboratoire

Thermo Scientific

Thermo Scientific NESLAB EX Series Instructions générales

Thermo Scientific

Thermo Scientific iCAP Q Manuel utilisateur

Thermo Scientific

Thermo Scientific TSQ 8000 Evo Manuel utilisateur

Thermo Scientific

Thermo Scientific Finnpipette Manuel utilisateur

Thermo Scientific

Thermo Scientific Nicolet Summit Manuel utilisateur

Thermo Scientific

Thermo Scientific TELESHAKE 1536-6 Manuel utilisateur

Thermo Scientific

Thermo Scientific TSQ Endura Manuel utilisateur

Thermo Scientific

Thermo Scientific Shandon TissueWave 2 Manuel

Thermo Scientific

Thermo Scientific MAXQ SHKE435HP Mode d'emploi

Thermo Scientific

Thermo Scientific MaxQ SHKE416HP Mode d'emploi

Thermo Scientific

Thermo Scientific Revco ULT1790-10-A Manuel utilisateur

Thermo Scientific

Thermo Scientific Dionex AutoTrace 280 Manuel utilisateur

Thermo Scientific

Thermo Scientific ISQ EC Manuel utilisateur

Thermo Scientific

Thermo Scientific 815 Mode d'emploi

Thermo Scientific

Thermo Scientific CryoStar NX50 Manuel

Thermo Scientific

Thermo Scientific Multifuge X1R Manuel utilisateur

Thermo Scientific

Thermo Scientific Finnpipette Novus Manuel utilisateur

Thermo Scientific

Thermo Scientific 3050 Manuel utilisateur

Thermo Scientific

Thermo Scientific TRACE 1600 Manuel utilisateur

Thermo Scientific

Thermo Scientific Barnstead GenPure xCAD Plus System Manuel utilisateur

Thermo Scientific

Thermo Scientific KingFisher Flex Manuel utilisateur

Thermo Scientific

Thermo Scientific Invitrogen E-Gel G8000 Manuel utilisateur

Thermo Scientific

Thermo Scientific VF-F20-A Manuel utilisateur

Thermo Scientific

Thermo Scientific AquaSensors AquaTrace Manuel utilisateur

Manuels Équipement de laboratoire populaires d'autres marques

Qiagen

Qiagen DML 3000 Manuel utilisateur

Queensgate

Queensgate NANOSCAN OP400 Manuel de programmation

Conviron

Conviron GEN1000-GE Manuel utilisateur

Parr Instrument

Parr Instrument 4560 Mode d’emploi

IKA

IKA IC control Manuel utilisateur

Integra

Integra DOSE IT Manuel utilisateur

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuel utilisateur

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuel utilisateur

NI PXI-5422 Manuel

Collomix

Collomix Aqix Manuel utilisateur

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur

Ocean Insight

Ocean Insight FLAME-NIR+ Manuel utilisateur

Parker

Parker ALIGN-MG-NA Manuel utilisateur

BD 644787 Manuel utilisateur

DENTAURUM

DENTAURUM Compact Megaplus Manuel utilisateur

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuel utilisateur

VWR

VWR SAS Super IAQ Manuel utilisateur

illumina

illumina MiSeqDx Manuel utilisateur