Thermo King TriPac Envidia Manuel utilisateur

Distributed by:

Printed in U.S.A.

314 West 90th Street

Minneapolis, MN 55420

Direct (952) 887-2200

Thermo King Corporate

Distributed by:

314 West 90th Street

Minneapolis, MN 55420

Direct (952) 887-2200

Thermo King Corporate

Distributed by:

314 West 90th Street

Minneapolis, MN 55420

Direct (952) 887-2200

Thermo King Corporate

Distributed by:

Ingersoll Rand’s Climate Solutions sector delivers energy-efﬁ cient HVACR solutions for

customers globally. Its world class brands include Thermo King, the leader in transport

temperature control and Trane, a provider of energy efﬁ cient heating, ventilating and air

conditioning systems, building and contracting services, parts support and advanced controls

for commercial buildings and homes.

314 West 90th Street

Minneapolis, MN 55420

Direct (952) 887-2200

Thermo King Corporate

Installation ManualInstallation Manual

Installation ManualInstallation ManualInstallation Manual

Installation Manual

TriPac Envidia

Auxiliary Heating and Cooling

Temperature Management System

TK 56459-19-IM (Rev. 0, 12/17)

Installation Manual

TriPac Envidia

Auxiliary Heating and Cooling

Temperature Management System

TK 56459-19-IM (Rev. 0, 12/17)

Introduction

This manual was written only to assist with the installation of the Thermo King TriPac Envidia Auxiliary Heating

and Cooling Systems onto a typical Class 8 semi-tractor with sleeper. While it is not intended to be specific to a

particular vehicle, the information in this manual will provide the installer with details to correctly and safely install

each of the APU components.

Before beginning the installation, the installer should confirm with the customer the location for each of the APU’s

components by using the APU Installation Questionnaire. The customer should also be made aware that modifications to

existing equipment might be necessary to complete the installation.

Modifications may include:

•Tractor’s engine must be fitted with an upgraded alternator of 270 amps or more and with upgraded alternator

wiring of OEM approved design.

•APU condenser may be directly mounted to the outside of the sleeper.

•APU evaporator, power inverter and/or converter may be installed in existing storage spaces under the bunk or in

the toolbox areas.

•APU heating and A/C duct work may to be routed with vents installed in existing closets or storage compartments.

•OEM components on the chassis may need to be relocated to accommodate the installation of the APU battery box.

•OEM fuel tank may need to be changed to a smaller size to accommodate the installation of the APU battery box.

•For base level performance - tractor battery box must have four 12Vdc batteries connected to provide 12Vdc output.

•For optimum level performance - tractor batteries may be upgraded to Thermo King NXT 1150 CCA absorbed glass

mat (AGM) batteries.

Due to its complexity, you should not attempt this installation unless you:

•Are an experienced mechanic.

•Can safely lift 34 kilos (75 lbs.)

•In the U.S., EPA 608 certified and trained in the repair and maintenance of transport refrigeration systems.

•Have a basic understanding of electricity and electrical wiring.

•Have the necessary tools and equipment to complete the installation.

•Have a truck body designed and built to meet the requirements of this installation.

This manual is published for informational purposes only. Thermo King makes no representations warranties express or

implied, with respect to the information recommendations and descriptions contained herein. Information provided

should not be regarded as all-inclusive or covering all contingencies. If further information is required, Thermo King

Corporation Service Department should be consulted. Thermo King’s warranty shall not apply to any equipment which

has been “so installed, maintained, repaired or altered as, in the manufacturer’s judgment, to affect its integrity.”

Manufacturer shall have no liability to any person or entity for any personal injury, property damage or any other

direct, indirect, special, or consequential damages whatsoever, arising out of the use of this manual or any

information, recommendations or descriptions contained herein.

Table of Contents

Introduction................................................................................................................................................................2

Table of Contents .......................................................................................................................................................3

Tips for a Successful Installation................................................................................................................................5

Battery Box Dimensions.............................................................................................................................................9

Evaporator/Control Box Dimensions .......................................................................................................................11

Condenser with Receiver Drier Dimensions............................................................................................................12

HMI Dimensions......................................................................................................................................................13

1000 Watt Power Inverter Dimensions (Option)......................................................................................................14

AC/DC Shore Power Converter Dimensions (Option).............................................................................................15

D2/D4 Heater Dimensions (Option).........................................................................................................................16

Required Tools and Additional Supplies..................................................................................................................18

Typical Component Locations .................................................................................................................................19

Tractor and APU Battery Recommendations...........................................................................................................20

Battery Box Installation............................................................................................................................................22

Condenser and Receiver Drier Installation...............................................................................................................26

Evaporator/Control Box Installation ........................................................................................................................28

Fabricating Refrigeration Hoses...............................................................................................................................30

A/C Hose Installation...............................................................................................................................................34

A/C System Evacuation and Leak Check Procedures..............................................................................................36

D2/D4 Heater Installation (Heat Option).................................................................................................................37

D2/D4 Heater Duct Installation (Heat Option).........................................................................................................40

A/C Duct Installation................................................................................................................................................42

Battery Box Harness Installation..............................................................................................................................44

Condenser Fan and Sensor Harness Installation.......................................................................................................46

Ignition Switch and Harness Installation..................................................................................................................47

HMI Installation.......................................................................................................................................................48

USB Service Communication Cable..........................................................................................................................49

D2/D4 Heater Harness Installation (Heat Option) ...................................................................................................50

Fuel Pickup Tube Installation (Heat Option) ...........................................................................................................51

Heater Fuel Pump and Fuel Line Installation (Heat Option)....................................................................................55

Heater Fuel Pump Connections (Heat Option).........................................................................................................57

Auxiliary AC Power Accessories (Option)..............................................................................................................58

Installing Battery Cables ..........................................................................................................................................59

Priming the Heater Fuel Pump (Heat Option)..........................................................................................................61

Heater Start-Up Procedure (Heat Option)................................................................................................................62

A/C System Charging Procedure..............................................................................................................................66

Operation Checkout Procedures...............................................................................................................................67

Unit Setup.................................................................................................................................................................69

System Check List....................................................................................................................................................73

Tips for a Successful Installation

BEFORE BEGINNING THE INSTALLATION

•Read this manual to understand where components are to be located and how they are to be installed.

•Review component location diagram and discuss with the customer where each component will be installed on his

tractor.

•Verify tools and special equipment required for the installation are available and in good working condition.

•Open all installation kits and inspect the contents before beginning installation.

•It is recommended that one person performs the installation of all the components outside the sleeper while a

second person installs all the components inside the sleeper. This will help minimize any damage to the sleeper’s

interior from grease, dirt, etc.

TRACTOR ALTERNATOR

•Tractor’s engine must be fitted with an upgraded alternator of 270 amps or more and with upgraded alternator wiring of

OEM approved design.

TRACTOR’S BATTERIES

•It is important not to allow the tractor’s batteries to become discharged during the installation process. A battery

charger should be connected to the batteries while the installation is in process or shut the tractor’s battery power

supply completely off using the OEM main battery disconnect switch, if available. See Tractor and APU Battery

Recommendations section in this manual for more information.

APU BATTERIES

•Thermo King NXT AGM batteries are shipped fully charged and ready to use. See Tractor and APU Battery

Recommendations section in this manual for more information..

APU BATTERY BOX INSTALLATION

•IMPORTANT: DO NOT weld or drill holes in the top or bottom flanges of the tractor’s frame. Serious structural

damage could occur to the frame! Consult your chassis manufacturer for further information.

•The battery box is designed to be mounted only to the existing truck frame rails. NO OTHER MOUNTING

LOCATION IS ACCEPTABLE!

•Safely relocate components on the chassis that interfere with the installation of the battery box.

•Check clearance around battery box before beginning the installation.

•The use of a motorcycle/ATV lift or modified floor jack to raise battery box into position is recommended.

•Only the supplied spacer blocks and mounting claws must be used to install the battery box to the chassis frame rail.

•If different mounting bolts are used, they must be Grade 5 and of the correct length. DO NOT cut off excessive length

bolts.

•Verify the upper and lower battery box mounting bolts are square and flat with the chassis frame rail before

tightening.

•The mounting hardware securing the battery box to the tractor’s frame must be correctly positioned and torqued

using the four-step tightening sequence described in this manual.

Tips for a Successful Installation (continued)

A/C CONDENSER INSTALLATION

•Keep all the A/C fittings capped and sealed until the installation of the refrigeration hoses. Refrigerant oil is

extremely hygroscopic and a system left open for more than 5 minutes may require extensive

evacuation/dehydration time to remove moisture.

•Verify all measurements before drilling any mounting holes.

•Verify there is no interference with any OEM electrical wiring, internal supports, etc. before drilling mounting holes.

•Confirm the condenser location does not interfere with the service or operation of existing tractor components.

•Provide protection to the tractor’s interior and or exterior finish to prevent damage during the installation process.

•Use the stainless steel mounting hardware (supplied in the kit) to mount the condenser.

•Use the large fender washers (supplied in kit) inside the sleeper to provide additional support.

•All mounting holes must be sealed with silicone caulking to prevent Moisture or fumes from entering the sleeper.

A/C EVAPORATOR/CONTROL BOX INSTALLATION

•This installation requires a two-person or mechanically assisted lift.

•Keep all the A/C fittings capped and sealed until the installation of the refrigeration hoses. Refrigerant oil is

extremely hygroscopic and a system left open for more than 5 minutes may require extensive

evacuation/dehydration time to remove moisture.

•Determine the best location for the A/C Evaporator/Control Box inside the sleeper, typically under the bunk and flush

to the front bulkhead.

•Allow adequate clearance for attaching the two air outlet tubes.

•Verify there is no interference with any OEM electrical wiring, internal floor supports, etc. before drilling any mounting

holes in the tractor.

•The Evaporator/Control Box should be mounted directly onto the floor mat inside the sleeper. Use the supplied

template to properly locate the drain and mounting holes.

•Always install the drain valves (kazoos) into drain holes located on the bottom pan of the evaporator.

•The A/C vents should be located and installed to provide maximum air circulation in the sleeper such as: MEDIUM

(above lower bunk level) and HIGH (above upper bunk level). NOTE: Locating a vent LOW (floor level) is not

recommended. It will significantly reduce driver comfort and reduce maximum system run time.

•All mounting holes must be sealed with silicone caulk to prevent moisture or exhaust fumes from entering the

sleeper.

•All edges of access holes made in fiberglass and wood composite floors must be sealed correctly with fiberglass cloth

and resin.

Tips for a Successful Installation (continued)

D2/D4 HEATER INSTALLATION (Heat Option)

•Determine the best location of the heater inside the sleeper, typically under the bunk. Allow clearance for dismantling

for service.

•Install heater so it will maintain a minimum distance of 2.00 inches (50.8 mm) from any heat sensitive or flammable

material.

•The heater must only be mounted on a flat horizontal surface.

•Heater must be installed flush with the floor pan (i.e. sheet metal, fiberglass, etc.) to ensure proper sealing of the

mounting plate and gasket.

•All edges of access holes made in fiberglass and wood composite floors must be sealed correctly with fiberglass cloth

and resin.

•Outside air intake and exhaust hoses must be installed correctly for the heater to operate safely.

•Exhaust hose should be mounted slightly downwards to help drain off condensation.

•Install exhaust hose so it will maintain a minimum distance of 2.00 inches (50.8 mm) from any heat sensitive or

flammable material.

•Inside air inlet and outlet ducts must be installed correctly for the heater to operate safely:

•Pulse type fuel pump outlet must be installed at a 15 to 35 degree angle up from horizontal to operate correctly.

•Fuel pickup tube must be installed correctly in the fuel tank or the heater will not operate.

•Fuel line from the pickup tube to the fuel pump to the heater should be routed at a continuous rise. Use a hose cutter

or sharp knife to cut plastic fuel lines. Do not use a wire cutter as this will pinch the plastic fuel line closed.

•Do not route electrical wires, harness or battery cables together with fuel lines.

•BEFORE operating the heater, the fuel lines must be bled of air using the Heater Priming Harness (204-1144) or

damage to the fuel pump will result.

•The Diagnostic Code Reader (204-1143) must be used to setup and operate the heater in the run-in mode.

A/C HOSE CONNECTIONS AND ROUTING

•Keep all the A/C fittings capped and sealed until the installation of the refrigeration hoses. Refrigerant oil is

extremely hygroscopic and a system left open for more than 5 minutes may require extensive

evacuation/dehydration time to remove moisture.

•Only cut refrigerant hoses with the correct hose cutting tool (204-677). NEVER USE A SAW!

•Always use the correct hose fitting tool (204-1045) when assembling refrigeration hoses.

•Always lubricate hose fittings with Alkyl Benzene Refrigerant Oil (670404TKA) when assembling to refrigeration

hoses.

•Always install and lubricate O-rings with Alkyl Benzene Refrigerant Oil (670404TKA) when connecting

refrigeration hose fittings to component connection fittings.

•Refrigeration hoses should be installed onto components in such a way as to allow for vibration and movement of

the cab. THEY SHOULD NEVER BE STRETCHED TIGHT!

•All refrigeration connections should be tightened securely using two wrenches.

•Always keep refrigeration hoses from rubbing or chafing against sharp metal objects, rotating components or hot

components.

Tips for a Successful Installation (continued)

•Protective covers or sleeves (installer supplied) for the refrigeration hoses may be required depending on the

installation.

•Always install the condenser’s receiver drier so refrigerant flow is in the direction indicated by the arrow.

•Thermo King Evacuation Station (204-725) and Evacuation Station Operation and Field Application Instructions

(TK-40612) are recommended.

•The oil in the evacuation station vacuum pump should be changed after each use.

•The A/C system must be leak free. Check for leaks by using an electronic leak detector.

•The A/C system will be charged with 2.0 lbs. of R134a refrigerant. NOTE: Accuracy is important. Over or under

charge by 3 ounces will reduce cooling capacity.

ELECTRICAL WIRING AND HMI CONTROLLER INSTALLATION

•Electrical wiring should be installed and routed in such a way as to allow for vibration and movement of

the cab. THEY SHOULD NEVER BE STRETCHED TIGHT!

•Always keep electrical wiring fromrubbing or chafing against sharp metal objects, rotatingcomponents or hot objects.

•All electrical wiring should be neatly routed and secured with band wraps or clamps.

•Do note route or bundle 110Vac wires together with 12Vdc wires.

•Do not route electrical wires, harness or battery cables together with fuel lines.

•Excess length of battery cables should be cut off to reduce voltage drop.

•Superlube (203-524) or equivalent should be applied to all electrical connections.

•All main power and ground accessory connections must be installed directly on top of the tractor’s battery terminal

posts and tightened securely. DO NOT INSTALL UNDER OEM BATTERY CABLES!

Autres manuels pour TriPac Envidia

Table des matières

Autres manuels Thermo King Générateur portable

Thermo King

Thermo King TriPac Envidia Manuel utilisateur

Thermo King

Thermo King TriPac E Mode d'emploi

Thermo King

Thermo King TriPac 3 Manuel utilisateur

Thermo King

Thermo King SGCO 3000 Manuel utilisateur

Manuels Générateur portable populaires d'autres marques

Kohler

Kohler 20EORZ Mode d’emploi

Powerhorse

Powerhorse 83171 Manuel utilisateur

HURST

HURST ML-630-SI Manuel utilisateur

ETQ

ETQ TG4000 Manuel utilisateur

Briggs & Stratton

Briggs & Stratton 40265 Guide de configuration

ConMed

ConMed 7550 Manuel utilisateur

Owon

Owon Waveform Generator Manuel utilisateur

evertz

evertz 7700 Series Manuel utilisateur

Power Stroke

Power Stroke PS906025 Manuel utilisateur

Firefly

Firefly Cygnus CYG2400/460/24 Manuel utilisateur

Draper

Draper PG950S Mise à jour du firmware

PowerBoss

PowerBoss PowerBoss Manuel utilisateur

SDMO

SDMO SH 4000 Manuel utilisateur

EINHELL

EINHELL STE 5500 Manuel utilisateur

Wanco

Wanco WI3000P Manuel utilisateur

Full Boar

Full Boar FBT-3300 Manuel utilisateur

Dwyer Instruments

Dwyer Instruments ASG Manuel utilisateur

Westinghouse

Westinghouse WH1000i Series Manuel utilisateur