Thermastor ULTRA Series Instructions d'installation

800.533.7533 | Santa-Fe-Products.com Santa Fe ULTRAMD33 Installation & Operation Instructions

Serial Number

Install Date

Sold By

Installation & Operation Instructions

The Santa Fe UltraMD33 is a built-in

dehumidication solution that can be conveniently

installed inside standard wall framing. The Santa

Fe UltraMD33 provides the ultimate in:

+Comfort

+Health

+ Property Protection

ULTRA SERIES | ULTRAMD33

TS-1157 04/21 Rev A

Santa-Fe-Products.com | 800.533.7533

* The Santa Fe UltraMD33 was previously known as the Ultra Aire MD33. Patent: thermastor.com/patents

2Santa Fe ULTRAMD33 Installation & Operation Instructions Santa-Fe-Products.com | 800.533.7533

Safety Instructions ...................................................................... 3

Dehumidifier Set Up .................................................................... 5

Drain Installation Considerations ................................................ 6

Electrical Requirements .............................................................. 6

Dehumidifier Installation ............................................................. 7

Maintenance.............................................................................. 11

Air Flow...................................................................................... 11

Controls ..................................................................................... 12

Service....................................................................................... 14

Warranty .................................................................................... 16

TABLE OF CONTENTS

Santa Fe is committed to manufacturing quality products. To maintain

our standards, product specications may change without notice.

4201 Lien Road, Madison, WI 53704

(800) 533-7533

Thermastor.com | Santa-Fe-Products.com

FOR REPAIR & TECH SUPPORT: 1-800-533-7533 (follow prompts)

or CONTACT US AT: [email protected]

800.533.7533 | Santa-Fe-Products.com Santa Fe ULTRAMD33 Installation & Operation Instructions

SAFETY INSTRUCTIONS

WARNING!WARNING!

THIS SYMBOL MEANS IMPORTANT INSTRUCTIONS. FAILURE TO HEED THEM

CAN RESULT IN SERIOUS INJURY OR DEATH.

READ THE INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

CAREFULLY BEFORE INSTALLING AND OPERATING THIS DEVICE. PROPER

ADHERENCE TO THESE INSTRUCTIONS IS ESSENTIAL TO OBTAIN MAXIMUM

BENEFIT FROM THIS DEHUMIDIFIER.

CAUTION!CAUTION!

THIS SYMBOL MEANS IMPORTANT INSTRUCTIONS. FAILURE TO HEED THEM

CAN RESULT IN INJURY OR MATERIAL PROPERTY DAMAGE.

Registrations

The Santa Fe UltraMD33 conforms to unied standard UL 60335-2-40 and CSA Standard C22.2.60335-

2-40.

CAUTION!CAUTION!

READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION.

ALWAYS USE CAUTION AND WEAR CUT RESISTANT GLOVES WHEN HANDLING SHEET

METAL.

ALL STATE AND NATIONAL ELECTRICAL AND PLUMBING CODES MUST BE ADHERED TO

FOR PROPER UNIT OPERATION AND WARRANTY COMPLIANCE.

IMPROPER INSTALLATION MAY CAUSE PROPERTY DAMAGE OR INJURY.

INSTALLATION, SERVICE, AND MAINTENANCE MUST BE PERFORMED BY A QUALIFIED

SERVICE TECHNICIAN.

DEHUMIDIFIER IS HEAVY. HANDLE WITH CARE AND FOLLOW INSTALLATION INSTRUCTIONS.

THIS APPLIANCE IS INTENDED FOR USE AT ELEVATIONS BELOW 4000 M (13,000 FT).

THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING CHILDREN) WITH

REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES, OR LACK OF EXPERIENCE

OR KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION

CONCERNING THE USE OF THE APPLIANCE BY A PERSON RESPONSIBLE FOR THEIR

SAFETY. CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY DO NOT PLAY WITH

THE APPLIANCE.

WARNING!WARNING!

120 VOLTS MAY CAUSE SERIOUS INJURY FROM ELECTRIC SHOCK. TURN

OFF CIRCUIT BREAKER BEFORE STARTING INSTALLATION OR SERVICING,

AND LEAVE CIRCUIT BREAKER OFF UNTIL INSTALLATION OR SERVICE IS

COMPLETED.

4Santa Fe ULTRAMD33 Installation & Operation Instructions Santa-Fe-Products.com | 800.533.7533

SAFETY INSTRUCTIONS

AVERTISSEMENT!AVERTISSEMENT!

CE SYMBOLE DÉSIGNE DES INSTRUCTIONS IMPORTANTES. LE NON-RESPECT DE

CES INSTRUCTIONS PEUT ENTRAINER DE GRAVES BLESSURES, VOIRE LA MORT.

LISEZ ATTENTIVEMENT LES INSTRUCTIONS SUR LE FONCTIONNEMENT ET L’ENTRETIEN

RELIÉS À L’UTILISATION DE CETTE UNITÉ AVANT D’EN EFFECTUER L’INSTALLATION ET

L’UTILISATION. LE RESPECT DE CES INSTRUCTIONS EST PRIMORDIAL AFIN DE TIRER LE

MAXIMUM DE BÉNÉFICES DE VOTRE DÉSHUMIDIFICATEUR.

MISE EN GARDE!MISE EN GARDE!

CE SYMBOLE DÉSIGNE DES INSTRUCTIONS IMPORTANTES. LE NON-RESPECT

DE CES INSTRUCTIONS PEUT ENTRAINER DE GRAVES BLESSURES OU DES

DOMMAGES MATÉRIELS.

ENREGISTREMENTS

LE Santa Fe UltraMD33 EST FIDÈLE À LA NORME UNIFIÉE UL 60335-2-40 AINSI QU’À LA NORME

C22.2.60335-2-40.

MISE EN GARDE!MISE EN GARDE!

LISEZ LES CONSIGNES EN ENTIER AVANT DE COMMENCER L’INSTALLATION.

SOYEZ TOUJOURS VIGILANT ET PORTEZ DES GANTS RÉSISTANT AUX COUPURES LORSQUE

VOUS MANIPULEZ DES FEUILLES DE MÉTAL.

TOUS LES CODES DE L’ÉLECTRICITÉ NATIONALE ET D’ÉTAT DOIVENT ÊTRE RESPECTÉS POUR

UNE UTILISATION ADÉQUATE DE CETTE UNITÉ ET UNE VALIDITÉ DE LA GARANTIE.

UNE INSTALLATION NON CONFORME PEUT CAUSER DES DOMMAGES MATÉRIELS OU DES

BLESSURES.

TOUTE INSTALLATION, TOUT ENTRETIEN ET TOUTE RÉPARATION DOIVENT ÊTRE EFFECTUÉS

PAR UN TECHNICIEN D’ENTRETIEN QUALIFIÉ.

LE DÉSHUMIDIFICATEUR EST LOURD. MANIPULER AVEC SOIN ET SUIVRE LES INSTRUCTIONS

D’INSTALLATION.

ÉVITEZ D’UTILISER POUR LE FONCTIONNEMENT D’UNE PISCINE OU LA GARANTIE SERA

ANNULÉE.

CET APPAREIL EST PRÉVU POUR UNE UTILISATION EN ALTITUDE À PLUS DE 4000 M (13000 PI).

CET APPAREIL NE DOIT PAS ÊTRE UTILISÉ PAR DES PERSONNES DONT LES CAPACITÉS

PHYSIQUES, SENSORIELLES OU MENTALES SONT LIMITÉES (Y COMPRIS LES ENFANTS) OU DES

PERSONNES SANS EXPÉRIENCE NI CONNAISSANCES PERTINENTES POUR L’UTILISATION DE

L’APPAREIL À MOINS D’AVOIR ÉTÉ FORMÉES SUR L’UTILISATION DE L’APPAREIL PAR UNE

PERSONNE RESPONSABLE DE LEUR SÉCURITÉ. LES ENFANTS DEVRAIENT ÊTRE SUPERVISÉS

AFIN D’ÉVITER QU’ILS NE JOUENT AVEC L’APPAREIL.

AVERTISSEMENT!AVERTISSEMENT!

UNE DÉCHARGE ÉLECTRIQUE DE 120 VOLTS PEUT CAUSER DES BLESSURES

SÉRIEUSES. FERMEZ LE DISJONCTEUR AVANT DE COMMENCER L’INSTALLATION

OU L’ENTRETIEN ET LAISSEZ LE DISJONCTEUR EN POSITION FERMÉE JUSQU’À

CE QUE L’INSTALLATION OU L’ENTRETIEN SOIT COMPLÉTÉ(E).

800.533.7533 | Santa-Fe-Products.com Santa Fe ULTRAMD33 Installation & Operation Instructions

Important Precautions

• If used near a water source, be certain that there is no chance the unit could get splashed. Connecting the

unit to a dedicated circuit with Ground Fault Circuit Protection is recommended. Electrical wires must be

properly grounded, and with the capability to be disconnected to provide for service.

• The device is designed to be installed indoors in a space that is protected from rain and ooding.

• Tamper proof fasteners provide access to the front of the device for operation, maintenance and service.

• Avoid directing discharge air at occupants.

• DO NOT place sides, top or bottom of cabinet in direct contact with structural building members or

unwanted noise may result. Unit is designed to be suspended by side mounting anges only.

• Drain hose must be routed with downward slope from unit drain connection to appropriate location. Consult

local building codes for acceptable condensate drain connections.

Location Considerations

• Install the unit on or inside of an interior wall and with direct connection to building electrical service.

A 15 Amp circuit must be provided. Install the unit in a location that is near a power supply.

• Electrical and plumbing rough-in must be provided to installation location, adhering to any applicable local

codes.

• Install the unit in a central location to maximize air circulation and eciency. Do not locate inside a closet

or mechanical room with the diuser cover facing inward where both supply and return air will be limited.

• Install the unit such that discharge air is directed away from thermostats and not installed inside of a wall

cavity that contains a thermostat.

• The unit generates condensate. Install the unit with nearby access to a drain or determine if there will be a

need for a condensate pump.

• The unit will t within 16" O.C. stud walls. If walls are more or less than 16", consideration must be given to

providing additional support.

• Rough opening must be a minimum of 2" o the oor, 6" from the ceiling, and 10"from an inside corner.

• Check that there are no hidden wires or pipes inside the wall where unit is to be installed. Contact a certied

electrician or plumber before removing any wires or pipes inside the wall.

DEHUMIDIFIER SET UP

6Santa Fe ULTRAMD33 Installation & Operation Instructions Santa-Fe-Products.com | 800.533.7533

A 10' long power cord is included for installations where a plug in connection is permitted in accordance with

the National Electrical Code and local codes and ordinances. A dedicated 15A circuit and GFCI receptacle

are recommended. Electrical connections inside the device are made with the included wire nuts. Route the

cord through the appropriate knockout and secure with the non-metallic cable clamp.

If not using the included 10' power cord,

ensure that the electrical connection and

wire size are adequate and in conformance

with the National Electrical Code,

ANSI/NFPA 70 – latest edition and all local

codes and ordinances. Use exible,

armored, or non-metallic sheathed, copper

wire with grounding conductor. Use the

included non-metallic cable clamp as required.

• The Santa Fe UltraMD33 requires 120-volt,

60 Hz, AC-only, 15 amp, fused and

grounded electrical supply.

• A visible circuit breaker or disconnect

switch near the unit is required for

maintenance and service.

• A dedicated circuit is recommended.

• Use of a UL listed or CSA approved

strain relief is required.

ELECTRICAL REQUIREMENTS

Wiring Schematic

DRAIN INSTALLATION CONSIDERATIONS

Consult local building codes for condensate drain restriction and additional requirements. The Santa Fe Ul-

traMD33 is provided with 10' of 3/4" I.D. drain hose. Verify drain hose length is appropriate for application.

The hose must be connected to the drain port and routed down the wall cavity and into the air conditioning

condensate drain or other acceptable drainage.

• For gravity drainage, the bottom of the unit must be at, or above the drain height.

• Avoid any entrapment of stagnant water within the hose.

• Consider 1/4" drop for every foot of drain hose.

• Codes may dictate that a drain trap is necessary before or near to the main building drain.

Be sure to install the metal cover over the top of the hose. This prevents air from entering the unit through

the wall cavity.

800.533.7533 | Santa-Fe-Products.com Santa Fe ULTRAMD33 Installation & Operation Instructions

DEHUMIDIFIER INSTALLATION

Tools Required:

• Phillips Screwdriver

• 1/4" Hex Nut Screwdriver

• Level

• Square or Ruler

• Stud Finder

• Wire Stripper

• Drywall Saw

• Side Cutters or Carpenters Knife

• Tape Measure

• Pen or Pencil

Other Materials To Consider:

• Electrical wire (depends on

installation and distance of

wiring requirements)

• Additional hose length or PVC

pipe (depends on drain location)

• Materials to repair drywall

(depends on installation)

• Condensate Pump Kit

(depends on drain location)

• GFCI Outlet (if using supplied

power cord)

Step 1. Remove the shipping bracket by carefully

cutting the two zip ties with side cutters or shears.

Remove the four screws from the shipping bracket

using a 1/4" hex nut screwdriver.

Step 2. Remove electrical box cover from the unit by

removing the two screws on the cover using a 1/4" hex

nut screwdriver.

WARNING!WARNING!

SHUT OFF BREAKER / POWER BEFORE BEGINNING INSTALLATION.

Electrical

Box

Shipping

Bracket

AVERTISSEMENT!AVERTISSEMENT!

FERMEZ LE DISJONCTEUR/ALIMENTATION AVANT DE COMMENCER L’INSTALLATION.

Items Included in Box:

• Santa Fe UltraMD33 Dehumidier

• Diuser Cover with Filter

• Santa Fe UltraMD33 Installation

Instructions

• Drain Hose (10')

• Power Cord (10')

• Hose Clamp

• Grommet for Drain Hose

• Non-Metallic Cable Clamp

• Bag A: #10 Wood Screws (5)

• Bag B: #8 Sheet Metal Screws (5)

• Bag C: Tamper Resistant Screws for

Diuser Cover (5) and 1/4" Hex T-15

Torx Security Bit

• Bag D: Phillips Screws for Diuser

Cover (5)

The Santa Fe UltraMD33 can be installed in a variety of applications:

• 2x6 16" O.C. Stud Wall Installation

• 2x4 16" O.C. Stud Wall Installation

- If penetrating both walls and the opposite side is a mechanical room, no additional accessories are needed.

- If back wall is functional space, installation requires 2x4 Wall Mount Bezel Kit (PN 4037767).

- If the other side of the wall goes into an unconditioned space, it may require the 2x4 Rear Panel Kit (PN

4037768) to add a layer of insulation to prevent condensation.

• Surface Mount Installation

- Surface Mount Kit (PN 4037766) required for installation.

Surface Mount, Bezel Kit and Rear Panel installations can be viewed at www.inwalldehumidier.com/accessories

8Santa Fe ULTRAMD33 Installation & Operation Instructions Santa-Fe-Products.com | 800.533.7533

DEHUMIDIFIER INSTALLATION

Inside of Wall

Drain

Hose

Electrical

Wiring

14 1/2"

30 1/4

14"

Steps 5 - 8

Step 4. The drain hose can exit through the back,

side, or bottom of the unit. Once the location is

determined, remove the appropriate knock out.

If exiting through the bottom, remove the access

cover to facilitate routing of the drain line.

Save access cover for reinstallation after drain

line is routed.

Step 5. After installation location has been determined,

use a stud nder, locate and mark stud walls.

Step 6. Using measuring tape and pencil, measure

14 1/2" across and 30 1/4" down and draw a line.

Step 7. Using a square or ruler, score the lines

and cut with drywall saw.

Depending on installation, both walls may need to

be cut through.

Step 3. There are three electrical knock outs, one on

the back and two on the bottom of the unit. Remove

appropriate knock out and install non-metallic cable

clamp with clamp screws inside of unit oriented so

they are accessible for tightening later.

If using included power cord, insert cord through non-

metallic cable clamp so that a minimum of ½” insulation

jacket is inside of cabinet before tightening non-metallic

cable clamp screws. Make electrical connections using

included wire nuts.

Step 8. If not using included power cord, route the

electrical wire from the circuit breaker or disconnect

switch through the wall cavity and extend out of the

opening by 14" to 20".

Use the 10' drain hose provided or the appropriate

length of hose to come through the wall cavity

or back of the unit and extend out of the opening

by 14".

If cutting through both walls, electrical wiring

and drain hose may be routed dierently. Use

appropriate routing for your installation.

WARNING!WARNING!

SHUT OFF BREAKER / POWER

BEFORE BEGINNING INSTALLATION.

800.533.7533 | Santa-Fe-Products.com Santa Fe ULTRAMD33 Installation & Operation Instructions

Step 10. Once electrical and drain hose are routed

through the unit, set the unit into the wall.

Step 9. Lift the unit and place it near the wall opening to route

electrical wires and drain hose through appropriate knock outs.

If access cover was not removed, insert grommet into knock out

hole and snap into place before routing drain hose through.

It is recommended to have two people to lift the unit. Place

one hand under the drain pan to support the unit during this step.

Wall

MD33

14 1/2"

Side View

Drain Hose

and Electrical

Steps 9 - 10

DEHUMIDIFIER INSTALLATION

Step 11. Insert the dehumidier into the center of the opening,

allowing for a minimum of 1/8" clearance from framing on both

sides. Additional insulation or sound dampening material (not

provided) may be required if the dehumidier cabinet contacts

the studs, especially in applications involving metal studs.

Fasten the unit to the framing by inserting four of the #10

(wood) or #8 (sheet metal) screws into the slotted holes.

Top and bottom blocking is not necessary for securing the

dehumidier. Any existing blocking, headers or framing

should not intrude into the rough opening and be a minimum

of 1/2" away from the cabinet.

The cabinet is designed to create 1/2" clearance to the back

wall when installed inside a standard 2x6 stud space with

1/2" minimum drywall sheathing.

For alternate installations, maintain 1/2" clearance to back

of wall of dehumidifier cabinet.

11.

Before securing the unit into place, make sure it is level. Level

or slightly forward is acceptable, but never backwards.

15 1/2"

15"

0˚ 1˚-2˚ 1˚

OK OK NOT

Front

CAUTION!CAUTION!

THE UNIT IS NOT SECURED YET.

10 Santa Fe ULTRAMD33 Installation & Operation Instructions Santa-Fe-Products.com | 800.533.7533

Step 12. If the drain access cover was removed,

reinstall it by routing the drain hose through the

appropriate knock out and reattach the screw.

Route the grommet over the drain hose and snap

into place at the knock out.

Use 1/4" hex nut screwdriver to apply hose

clamp to the drain hose and secure onto the

drain port hose barb.

12.

Step 14. Tuck the electrical wires in and reinstall

electrical cover with its two screws using 1/4" hex

nut screwdriver. Be sure none of the electrical

wires are pinched.

Step 15. Turn breaker / power back on.

Step 16. Set the digital controller to desired

RH. See Controls Section on page 12.

Step 17. Install diuser cover by aligning

the lower tabs rst, then setting the cover

back against the wall. Insert the included

four tamper resistant or phillips screws to

secure the diuser cover.

DEHUMIDIFIER INSTALLATION

14.

17.

Step 13. Complete electrical connections:

• white to white

• green to green

• black to black

Screw wire nuts back onto each electrical

connection.

Then tighten clamp screws on non-metallic

cable clamp.

Power Board

Non-Metallic Cable Clamp

13.

Hose

Hose Clamp

Grommet for

Drain Hose

Make sure drain hose is routed to the appropriate

location before turning on the unit.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels thermastor Déshumidificateur

thermastor

thermastor Santa Fe Elite Manuel utilisateur

thermastor

thermastor Ultra-Aire 65H Manuel utilisateur

thermastor

thermastor Phoenix 300 Manuel utilisateur

thermastor

thermastor Quest 335 Manuel

thermastor

thermastor Phoenix R150 Manuel utilisateur

thermastor

thermastor Santa-Fe Advance 4029800 Manuel utilisateur

thermastor

thermastor HI-E Dry 195 Manuel

thermastor

thermastor Ultra-Aire 100V Manuel utilisateur

thermastor

thermastor PHOENIX DRYMAX BLE Manuel utilisateur

thermastor

thermastor 4028600 Manuel

thermastor

thermastor Ultra-Aire XT155XT Manuel utilisateur

thermastor

thermastor Santa-Fe Classic Manuel utilisateur

thermastor

thermastor Ultra-Aire 100V Manuel utilisateur

thermastor

thermastor 4031470 Manuel utilisateur

thermastor

thermastor Ultra Aire XT105H Manuel utilisateur

thermastor

thermastor HI-E Dry Vehere Manuel utilisateur

thermastor

thermastor Santa-Fe Manuel utilisateur

thermastor

thermastor Phoenix 200HT LGR Manuel utilisateur

thermastor

thermastor Ultra Aire 90H Manuel utilisateur

thermastor

thermastor PHOENIX DRYMAX XL Manuel utilisateur

thermastor

thermastor Phoenix R125 Manuel utilisateur

thermastor

thermastor Phoenix D850 Manuel utilisateur

thermastor

thermastor Ultra-Aire XT150H Manuel utilisateur

thermastor

thermastor Quest PowerDry 4000 Pro Manuel

Manuels Déshumidificateur populaires d'autres marques

Daitsu

Daitsu CD031IU-DFA Manuel utilisateur

Fehom

Fehom PDGT701BE Manuel utilisateur

Hitachi

Hitachi RD-190GX Manuel utilisateur

Westpoint

Westpoint MDF1-30AE Manuel utilisateur

SOLIS

SOLIS easy dry compact Manuel utilisateur

ENVIROBOSS

ENVIROBOSS EB240 Manuel utilisateur

Sinclair

Sinclair R-9112 Manuel utilisateur

Kenmore

Kenmore 580.54701 Manuel utilisateur

Demargo

Demargo DM828NF Manuel utilisateur

Altrad Lescha

Altrad Lescha LDH 600 Manuel utilisateur

BOMANN

BOMANN LE 1150 CB Manuel utilisateur

SPT

SPT SD-46 Manuel utilisateur

REMKO

REMKO SLN 40 Manuel utilisateur

Haier

Haier HD458 Manuel utilisateur

Logik

Logik L20DHW12 Manuel utilisateur

Frigidaire

Frigidaire FDR30S1 - 30 Pint Capacity Dehumidifier Guide de démarrage rapide

Blitz

Blitz HHD Series Manuel utilisateur

Prem-I-Air

Prem-I-Air PD14DEN Manuel utilisateur

thermastor ULTRA Series Instructions d'installation

Manuels Déshumidificateur populaires d'autres marques