Thelin TIBURON Manuel d'utilisation original

TIBURON PELLET - ASH PAN

Service Instruction

Figure 1

Figure 2

Figure 3

OVERVIEW

The Thelin Pellet heater is equipped with a long life DC fan motor

(Figure 1). This motor utilizes a special brush material that may

require additional break in time to properly wear in or seat the

brushes. When the motor is new the brush has a contoured end

that allows for minimum contact initially to facilitate the break in.

As this wears the full width of the brush begins to contact the

armature allowing for proper operation.

We have found that a small quantity of motors have not

immediately seated the brushes. The fan motor condition is easily

corrected by dressing the brushes and reinstalling them.

Testing for a fan motor brush problem is accomplished by two

methods. After recycling the heater by unplugging and

reestablishing power. Press the “Fan” switch only. If the fan runs

push the Clean button and allow the motor speed to increase to

full speed. If the motor appears to be operating at less than full

speed cleaning and seating the brushes will be required.

Included in this kit: (2) P/N 00.0035.0213 motor brushes, (1)

instruction.

Tools Required: #2 Phillips screw driver, medium flat blade, small

flat blade, #200 or fine sand paper strip (Figure 2).

Accessing the motor for brush service: The fan motor is

accessed from the bottom of the heater by removing the phillips

screws on the Fan Cover. Remove the convection fan blade

retention clip and blade. Note the access varies based on heater

model and may require removing the fan motor at the housing

(Figure 3).

Removing the wire harness connections : Using care not to

bend the fan blade, carefully use a flat blade screw driver to help

pry off the red and black motor wire terminals (Figure 3). Note

the brush holders have a corresponding red and black base to

confirm wire connections.

Removing the brush caps: Using a small flat blade screw driver

remove one brush cap at a time. Care should be taken as the

brush holder has a spring that forces to the brush onto the

armature. This spring may cause the cap to pop out unless held

firmly (Figure 5).

Removing and dressing the brush: Remove the brush from the

holder by lifting up and sliding the brush and spring clear (Figure

4). Once the brush is clear hold the brush base and carefully take

a couple of swipes across the brush face with fine sand paper

(Figure 5).

Brush holder with access

63 Laxalt Dr. Carson City, NV 89706

Ph: 775-241-2586

www.thelinco.com

P/N Tiburon Ash Pan Service 03/18

Figure 6

Figure 4

Figure 5

NOTE: WHEN SANDING THE FACE OF THE BRUSH DO NOT REMOVE ANY MATERIAL. WE ARE ONLY SCUFFING

THE SURFACE TO ALLOW FOR BETTER BRUSH CONTACT.

Reinstalling the brush: Insert the brush back into the holder. Hold the

terminal tab into the holder. Carefully insert the cap and turn with a small

flat bladed screw driver. Use care not to cross thread the cap. Once the

cap is threaded lightly tighten against terminal tab (Figure 6).

Repeat service on lower brush.

Assembly: Reconnect motor wires to red and black terminals. Check fan

blade for bent blades by spinning by hand. If blades are not aligned

carefully bend back into place.

Carefully reinstall fan cover and confirm fan alignment and the fan blade

turns freely without hitting the shroud.

After completing the installation of the rear panel and tightening all the

phillips screws. Plug the heater back into AC power and test run by

running fan motor on “Fan” setting for 2 minutes and then running on

“Clean” for 30 seconds. Open hopper lid and run unit through a

beginning start up by pressing “Low” and allowing fan to ignitor and fan

to start up. If all appears to activate reinstall unit.

Additional information is available on line:

http://www.thelinco.com/customer-support/maintenance/index.php

Technical Customer Service - 775-241-2586 or tech@thelinco.com.

63 Laxalt Dr. Carson City, NV 89706

Ph: 775-241-2586

www.thelinco.com

P/N Tiburon Ash Pan Service 03/18

Table des matières

Autres manuels Thelin Poêle à granulés

Thelin

Thelin ECHO PELLET E.I. Guide de sécurité

Thelin

Thelin GNOME PELLET STOVE Manuel utilisateur

Thelin

Thelin providence Manuel utilisateur

Thelin

Thelin PARLOUR PELLET E.I. Manuel utilisateur

Thelin

Thelin Pellet Heater Guide de sécurité

Thelin

Thelin PARLOUR 3000 Manuel utilisateur

Thelin

Thelin ECHO-COMSTOCK PELLET E.I. II Manuel utilisateur

Thelin

Thelin ECHO PELLET E.I. Manuel utilisateur

Thelin

Thelin PARLOUR Manuel utilisateur

Thelin

Thelin PARLOUR Manuel utilisateur

Manuels Poêle à granulés populaires d'autres marques

SMG

SMG Comfort Bilt HP50GC Manuel utilisateur

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Manuel utilisateur

Quadra-Fire

Quadra-Fire MTV-E2-CSB Manuel utilisateur

Palazzetti

Palazzetti JP Series Guide d'installation

Travis Industries

Travis Industries Avalon 900 PS Manuel utilisateur

Flame

Flame FP-45 Manuel utilisateur

Astra

Astra P-7 Manuel utilisateur

Heatilator

Heatilator ECO-ADV-PS35 Manuel utilisateur

Cadel

Cadel aquos 24 h2O Manuel utilisateur

vicenza

vicenza V4.5 Manuel utilisateur

MCZ

MCZ VIVO 90 COMFORT AIR 9 M1 Manuel technique

Quadra-Fire

Quadra-Fire 1000 Gold Manuel du propriétaire

Ferroli

Ferroli GEMMA Manuel utilisateur

pleasant hearth

pleasant hearth PH35PS Series Manuel utilisateur

Breckwell

Breckwell Tradition P24FS Manuel utilisateur

Quadra-Fire

Quadra-Fire CB1200M-MBK Manuel utilisateur

England's Stove Works

England's Stove Works 25-EP Manuel utilisateur

Avalon

Avalon Astoria Manuel utilisateur