THE WORLD MODELS A322S Manuel utilisateur
Warning! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
*Specifications are subject to change without notice.*
INSTRUCTION MANUAL
Wing Span
Wing Area
Flying Weight
Fuselage Length
58.5 in / 1485 mm
539 sq in / 34.8 sq dm
6.5 Ib / 2970 g
49 in / 1250 mm
Specifications
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY(ARF)SERIES
MADE IN CHINA
The World Models
Manufacturing Co., Ltd.
www.theworldmodels.com
Requires : 0.46-0.55 cu. in. displacement 2-stroke
0.70-0.81 cu. in. displacement 4-stroke
6-channel radio w/ 6 standard servos.
(A322S)
A322PO31941709
INDEX
BEFORE YOU BEGIN
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P.1
P.2
P.3-P.13
P.14
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CAor Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for
warranty replacement. The manufacturer will replace any defective parts, but will not extend
to the parts that are good before gluing to defective parts during assembly. Warranty will
not cover any parts modified by customer.
Symbols used throughout this instruction manual comprise of the following :-
Read through the manual before you begin, so you will have an overall idea of what to do.
1
2
3
P.1
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Peel off shaded portion
covering film.
Pay close attention here!
Apply epoxy glue.
Must be purchased separately !
Drill holes with the specified
diameter (here: 3mm). Pierce the shaded portion
covering film.
3mm
Do not overlook this symbol !
Warning!
Apply thread locker
A322PO31941709
Parts List
P.2
COVERING:--
TOUGHLON STL 322F
TOUGHLON STL 322W
TOUGHLON STL 203 LIGHT GRAY
TOUGHLON STL 331 CUB YELLOW
LIGHTEX SGX 201 BLACK
LIGHTEX SGX 311 FERRARI RED
1.MAIN WING -- 1 pair
2.M2 NUT -- 8 pcs
SCREW PM2x6mm -- 8 pcs
WASHER d2xD5mm -- 16 pcs
MAIN LANDING GEAR COVERS -- 1 pair
PVC PLATE 0.5mm 20x60mm -- 2 pcs
180mm Y-CORD KW0021800 -- 1 pc.
3.WING JOINER 6x20x251mm -- 1 pc.
4.PUSHROD Ø1.8x75mm w/ Threads (ForAileron) -- 2 pcs
SCREW PB2x22mm -- 4 pcs
SCREW PB2x18mm -- 2 pcs
SCREW PWA2x8mm -- 8 pcs
TRI-HORN M3x14mm (S) PL4111221 -- 2 sets
STRAPER PL4112102 -- 2 pcs
CLEVIS PL4112103 -- 2 pcs
FUEL TUBE Ø6x5mm -- 4 pcs
SERVO MOUNTING PANEL PL5310000 -- 1 pair
DROP TANK -- 1 pc.
PLYWOOD(A) -- 1 pc.
PLYWOOD(B) -- 1 pc.
SCREW PM2x12mm -- 2 pcs
M2 NUT -- 2 pcs
WASHER d2xD5mm -- 4 pcs
5.PLASTIC RING PL4112023 -- 2 pcs
Y-TYPE PUSHROD Ø1.8x92mm (For Flap) -- 1 pc.
STRAPER PL4112102 -- 1 pc.
CLEVIS PL4112103 -- 2 pcs
FUEL TUBE Ø6x5mm -- 3 pcs
6.TAIL LANDING GEAR PL7100001 -- 1 set
FUSELAGE -- 1 pc.
COLLAR Ø2.1mm w/ set screw -- 1 set
TAIL WHEEL Ø25mm -- 1 pc.
SCREW PA3x10mm -- 2 pcs
7.VERTICAL FIN & RUDDER -- 1 set
8.STABILIZER & ELEVATOR -- 1 set
9.PUSHROD Ø1.8x615mm w/ Threads (For Elevator) -- 2 pcs
SCREW PB2x16mm -- 6 pcs
TRI-HORN M3x14mm (S) PL4111221 -- 2 sets
CLEVIS PL4112103 -- 2 pcs
FUEL TUBE Ø6x5mm -- 2 pcs
10.PUSHROD Ø1.8x740mm w/ Threads (For Rudder) -- 1 pc.
SCREW PB2x16mm -- 3 pcs
TRI-HORN M3x22mm (S) PL4111301 -- 1 set
CLEVIS PL4112103 -- 1 pc.
FUEL TUBE Ø6x5mm -- 1 pc.
11.ENGINE MOUNT PL5111050 -- 1 set
SOCKET HEAD SCREW M4x25mm -- 4 pcs
WASHER d4xD9mm -- 4 pcs
12.FUEL TANK 380cc PL1111380 -- 1 set
CABLE TIE 1.5x5x400mm -- 1 pc.
DOUBLE-SIDE TAPE 40x100mm -- 1 pc.
13.SOCKET HEAD SCREW M3x30mm -- 4 pcs
M3 NUT -- 8 pcs
WASHER d3xD7mm -- 8 pcs
THROTTLE PUSHWIRE Ø1.2x320mm -- 1 pc.
PLASTIC TUBE d2xD3x230mm -- 1 pc.
14.COWLING --1 pc.
TRANSPARENT 3D TEMPLATE -- 1 pc.
SCREW PWA2.6x12mm -- 4 pcs
SILICON GROMMET d1.5xD6.5mm PL1265035 -- 4 pcs
SPINNER Ø76mm -- 1 set
15.LINKAGE CONNECTOR Ø2.1mm HW7111060 -- 1 set
16.PUSHROD CONNECTOR PL4410010 -- 1 set
PUSHROD Ø1.8x65mm (For Elevator) -- 1 pc.
STRAPER PL4112102 -- 2 pcs
FUEL TUBE Ø6x5mm -- 2 pcs
SPONGE 70x105x60mm -- 1 pc.
BALSA 5x5x107mm -- 2 pcs
17.SCREW HM4x40mm -- 2 pcs
WASHER d4.2xD14.5mm -- 2 pcs
18.CANOPY -- 1 pc.
SCREW PWA2.3x8mm -- 4 pcs
SILICON GROMMET d1.5xD6.5mm PL1265035 -- 4 pcs
PILOT PC001050A -- 1 pc.
WIRE Ø2mm -- 1 pc.
19.DECALS: A322DEC -- 1 set
A322PO31941709
Bottom View
Bottom View
P.3
Aileron Servo Lead
Pre-glued
M2 Nut
PM2x6mm Screw
8
8
16
d2xD5mm Washer
Completed
Please dry fit wing joiner into left and right wing to make sure they fit with the
proper dihedral angle, mark the wing joiner if necessary. Apply epoxy glue to
both sides of all surfaces in contact. Use a stick to apply the glue to inner side
of wing joiner sleeve, and apply the glue to wing joiner before putting them
together. Wing joiner not glued properly will lead to wing failure and plane crash.
PM2x6mm
M2 Nut
M2 Nut
d2xD5mm
Washer
d2xD5mm
Washer
d2xD5mm
Washer
Main Wing
1
Main Wing
3
Retractable Landing Gear
2
Wing Joiner 6x20x251mm
Lead to retract servo Lead to retract servo
4.8V - 6.0V operation
only, higher voltage
will burn out the
retract motor.
A322PO31941709
Aileron Servo & Drop Tank
Bottom View
P.4
4
Straper Fuel Tube
6x5mmØ
Ø1mm pilot holes for World Models tri-horn are
pre-drilled. Please look for pin-hole marks at
under side of control surfaces.
1.5mm
TWM PL8210010
CLEVIS WRENCH
Pushrod
1.8x75mm
Fuel Tube
Clevis
6x5mm
PB2x22mm
PB2x18mm
Tri-horn
M3x14mm(s)
PWA2x8mm
PWA2x8 mm
Screw
8
PB2x22mm Screw
4
PB2x18mm Screw
2
Plywood
Missile
M2 Nut
PM2x12mm
d2xD5mm
Washer
d2xD5mm
Washer Bottom View
Drop Tank Setup
Plywood (A)
Plywood (B)
Top View Bottom View
Plywood(A)
Plywood(B)
A322PO31941709
Flap
P.5
5
TWM PL8210010
CLEVIS WRENCH
Flaps up Flaps Down
Lead to Flap Servo
Fuel Tube
Ø6 x 5mm
Straper
Y-Type Pushrod Ø1.8 x 92mm
Clevis Clevis
Lead toAileron Servo
Lead toAileron Servo
Lead toFlap Servo
Ring
A322PO31941709
Vertical Fin & Rudder
P.6
7
A A'
A=A'
(Vertical Fin)
Completed
Pre-glued
Tail Landing Gear
6
PA3x10mm Screw
2.1mm
3mm Set Screw
Collar
PA3x10mm 2.1mm Collar
Tail Wheel
Ø
25mm
3mm Set Screw
2
1
1
1.5mm
Bottom View
2.5mm
A322PO31941709
P.7
Rudder Pushrod
10
Elevator Pushrod
9
Ø1mm pilot holes for World Models tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
PB2x16mm Screw
6
ElevatorPushrod
Ø1.8x615mm
Fuel Tube
Ø6x5mm
Clevis
PB2x16mm
Tri-horn
M3x14mm
Bottom View
Ø1mm pilot holes for World Models tri-horn are pre-drilled.
Please look for pin-hole marks at side of control surfaces.
PB2x16mm Screw
3
Bottom View
PB2x16mm
Clevis
Fuel Tube
Tri-horn
M3x22mm
Rudder Pushrod
Ø1.8x740mm
Ø6x5mm
Stabilizer & Elevator
8
B B'
B=B'
(Stabilizer)
(Main Wing)
C C'
C=C'
Temporary install the main wing, adjust leveling of the stabilizer
to make it as parallel to the main wing as possible
Completed
A322PO31941709
P.8
Engine Mount
11
Fuel Tank
12
M4x25mm Socket Head Screw
d4xD9mm Washer
4
4
Apply thread locker to screws
Blind nuts are off-centered to keep
the spinner at the fuselage axis.
Engine Mount
PL5111050
d4xD9mm Washer
Socket Head Screw
M4x25mm
UP
Cable Tie 1.5x5x400mm
Fuel Tank
380cc
Bottom View
Fuel Tank
380cc
Double-side Tape
40x100mm
Bottom View Completed
A322PO31941709
P.9
Engine
13
Cowling
14
M3x30mm Socket Head Screw
d3xD7mm Washer
4
8
8
Installed Engine Position
130mm
5.12in
Throttle Pushwire
Ø1.2x320mm
Plastic Tube
d2xD3x230mm
M3x30mm Socket Head Screw
d3xD7 Washer
M3 Nut
M3
Nu
t
PWA2.6x12mm Screw
4
First insert the grommet to the cowling then apply screw.
Please refer to the attached sheet for usage of the
transparent 3D template.
d1.5xD6.5mm
Grommet
Cowling
Spinner
Ø76mm
Fuselage
PWA2.6x12mm
4
d1.5xD6.5mm
Silicon Grommet
Completed
A322PO31941709
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels THE WORLD MODELS Jouet
THE WORLD MODELS
THE WORLD MODELS Extra 300 EP Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS 30% Stearman PT-17 Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS VOODOO MUSTANG-46 Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS CAP 232-46S Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS PAULISTINHA P-56 EP Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS ZERO FIGHTER 40 Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS T-34 Mentor Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS MIDGET MUSTANG Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS Sky Raider Mach II Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS 50CC SKY LINK Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS Groovy 50 3A Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS Jeff Troy's TAMEcat Trainer 40 ARF Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS Delta Jet EP Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS Spot-On 50 Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS AirMaster 5000 Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS Spot-On 50 Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS Sky Raider Mach II Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS La-Flyer-40 Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS Super Chipmunk-90 RF Manuel utilisateur
THE WORLD MODELS
THE WORLD MODELS Sky Runner Manuel utilisateur
