The Distillery Network EZ KIT Manuel utilisateur
TDN
BooKitLet
Introduction
Are you up for a challenge?
The EZ KIT you just purchased comes with a challenge; this is not a kit for
amateurs, but for the “DIY” kind of guy or girl.
Assembling the EZ KIT is not easy; you have to attach, clamp and solder
each piece yourself. We have already cut, bent, rolled and embossed the
copper for you to get you started.
Now it’s up to you to rise up to the challenge.
How rewarding would it be to be able to BRAG to all your friends and family
that you actually built a Copper Moonshine Still yourself! Or better yet,
build it with the help of a friend or family member as a quality time project.
We included this BooKitLet (yeah, that’s what we called this awesome thing)
with very detailed instructions on how to get your Still ready to rock. How-
ever you decide to tackle this, we promise you that you will not be alone
along the way, we are just a phone call away if you have questions!
1-(603) 997-6786
We also have an instruction video on our website for you to follow along.
Go to www.moonshinekits.com to watch.
So, turn to the page with a list of Tools Needed and get ready to build your
own Copper Moonshine Still!
Good Luck Moonshine Kit Rockstar.
INTRODUCTION
Page 1
KIT INSTRUCTIONS
PARTS INCLUDED:
Pot and Circle
(Bottom)
Thumper and Two Circles
(Top and Bottom)
Worm and One Circle
(Bottom)
Cap Kit
(Bottom, Top, Tip Top)
Cone Coil for
Worm
Temp Gaugue
and Brass Housing
1x1/2 inch Reduced Fitting
for Lyne Arm
1/2x1/4 inch Reducing Fitting
for Coil
Brass Plug and Bushing
for Thumper
Spin Unions
(Connectors)
90Degree
Fittings
45 Degree
Fittings
Copper Pipe
Pieces
Flux Solder
¾ Garden Hose
Hookups
* Gloves and eye googles
* Metal Snips for Custom Cuts
* Small Ball Hammer
* Metal File for Sharp Edges
* Propane Torch Head
* Propane tank (small, disposable)
* Fire Extinguisher and other safety supplies
* Long Flat Head Screwdriver
* Step Drill Bit
* Deburring Tool (if needed)
* Anything made of metal to hold up the bottom of the pot from the
inside Or a 5 Gallon bucket lined with tin foil
(to hold circle bottom piece into place when fitting it)
* Clamps to hold the seams together when soldering
(Have different length sizes on hand)
* Tin Foil
Page 2
Tools Needed:
Page 3
Pot Body Assembly
The Pot has two sides of the seam: a sharp side and a tucked seam side.
The Sharp side goes on the inside of the pot, it tucks under the folded over side.
Apply flux to the sharp seam on the outside and to the folded over side to the
inside (the flux sides will touch when you fold them over). Clamp the seams
together on the folded over seam.
Our mission here is to clamp the pot to the correct size of the bottom circle.
Clamp the pot so the circle fits snug, you want it on the tighter side rather than
loose. This is important, please remember copper is soft and you will want it
tight, so the solder makes a connection.
Folded Over
Side
Sharp Side
Page 4
Start soldering inside the pot seams. Use the heat and folow with the
solder, you’ll heat up the copper to melt the solder.
Go slow, making sure the solder drips into the gaps of the seam. Your first
run of soldering is to fill the gaps, you will do a second run along the seam
to make it look good.
Insert the pot circle and use something to push the circle up from the
inside, as to keep it in place while you solder the circle. Same as with the
pot seams solder slowly; making sure there are no gaps, circle has to be
snug.
Let it Cool and take the clamps off.
Thumper Assembly
Thumper comes with two copper circles.
One of these circles has two drilled holes; this one is the top circle.
Same as the pot, insert bottom circle and solder.
Turn over and insert the top, use a tool to pull up the edges to solder
nice and flat.
Continued
Pot Body Assembly
Page 5
Cap Bottom
Beveled Line
Cap Top
Cap TipTop
Clamp and solder the open cylinder (cap bottom) just as you did with
the pot body.
The bottom piece of the Cap has two lines, a beveled line and an em-
bossed line. Embossed line is under beveled line.
Flux the seams of Cap Top and Bottom; Insert the Cap top on Bottom
with beveled line on top, match the seams as these interlock. Get the
tightest fit you can, flux seams again and start soldering as you did
with the pot.
Make Two runs of solder inside the cap pieces (you can always do a
small solder line on the outside for added security).
Included is a flat square of copper, this is your Cap Tip Top; you can cut
this into a circle to fit the cap top.
Using the top piece of the cap as a guide, draw a circle with marker on
the inside to make a stencil of the right size.
Cut the circle shape, leaving about a 1/8” extra when you cut, this will
help make sure the circle you cut is not too small for the cap. Fit the
circle into the top of Cap Kit, use something inside to drive the circle up
and keep it in place while you solder (any metal cylinder would work).
Flux the seams along circle and solder.
Cap Kit Assembly
Page 6
As we saw with the pot body, the Cone also has two sides: a sharp side and a
folded over side. The folded over side is always on the outside, covering the
sharp edge side.
Flux the sharp side of the seam on the side facing towards you, flux the
seam of the folded over side as well, just as we did with the pot.
Match the bottom of cone seams first and when you fold the seams over each
other, leave about 2” overhang on the bottom and about ¼” on top to be able
to fit the clamps (Don’t clamp the seam, you will be soldering the seam).
Clamp the top and bottom and use a longer handle clamp to clamp the
middle of the cone, we do not want any gaps. Close the gap well so the
copper sides are touching each other.
Flux and solder from the inside, make sure to fill the gaps well with the
solder. Solder in two runs: the first run is to fill the gaps well; the second run
is to make it look nice and even.
Wait for the solder to cool, remove clamps.
Folded Over
Side
Sharp Side
Cone Assembly
Page 7
For this step, you will need an object such as a metal stand, metal object or a 5
gallon bucket lined with tin foil (to prevent melting), this will help you hold the
cone into place while you insert the pot body and solder.
Flip cone upside down on the bucket (holder) and fit the pot into the cone and
match up the seams.
Apply pressure to the top of the pot before soldering, to make gaps tighter.
(you may want to have another person pushing down to make sure gaps are
tight, or you can use a weight as well).
Flux along the seam of Cone and Pot and solder, go slow, in 3” stretches.
Assembly Pot to Cone
(cone to body connection)
Page 8
Assembly Cap to Cone
Just as we did with the Pot to Cone assembly, attach Cap to small end of
cone making sure the seams match (these should interlock).
Have someone help you keeping into place, or have something holding
the Cap in place (make sure whatever you use keeps the two pieces
steady!)
flux and solder leaving no gaps. Use low heat, do not overheat and do
not force the solder into the seams. Make it so the solder flows
naturally and the flame and the flux do all the work.
Ce manuel convient aux modèles suivants
1
Table des matières
