Texecom Azura 360 Manuel utilisateur

2INS154-4

Contents

Section Page

1. Installation 3

1.1 Mounting the Unit 3

1.2 Patented Engineer Hold-Off Mode 3

1.3 Installing the Unit 3

1.3.1 Optional “Battery First” Connection Method 4

1.4 Installing Multiple Units 5

1.4.1 SCB Mode 5

1.5 Commissioning 6

2. Servicing 6

3. Safety 7

4. Technical Specification 8

5. Warranty 10

6. Registered Installer Application Form 11

INS154-4 3

1. Installation

1.1 Mounting the Unit

Select a suitable position to mount the unit, which satisfies the following criteria:

•Highly prominent for maximum deterrence

•Additional shelter (e.g. under the eaves) is an advantage

•High enough to be out of normal reach to deter tampering

•Safe ladder access

•Good cable access

In addition to the corner screw fixing points, the unit also has a central keyhole to

simplify mounting and aid levelling.

Four screws and wall plugs are required for mounting the backplate to an even

surface. An additional screw may be required to provide wall tamper by fitting

through the screw hole next to the dual tamper microswitch. In doing so, care must

be taken to leave the screw head slightly proud to ensure that the microswitch

remains level and closes correctly when the outer cover is fitted.

For safety reasons the unit must be mounted securely on a suitable wall.

For maximum weatherproofing the unit should be flat to the wall.

For brick walls, BS 4737 specifies a minimum of three No. 10 steel screws

penetrating the brick (not the mortar or facing) by at least 40mm into suitable wall

plugs.

1.2 Patented Engineer Hold-Off Mode

For safety reasons, each Texecom sounder and strobe unit incorporates a unique

patented engineer Hold-Off mode. This mode prevents the unit from self-activating

during installation and maintenance, thereby allowing only bona fide engineers

access to the unit without any loss of tamper protection.

1.3 Installing the Unit

Connect the unit to the control panel as follows:

A(12V ) Permanent Positive Supply

B(BELL) Negative Applied Output to Activate Siren

C(TAMP) Negative Removed on Tamper Input

D(0V) Permanent Negative Supply

S(STRB) Negative Applied Output to Activate Strobe

Although the unit has been designed to be compatible with a wide range of control

panels, for optimum performance, it is highly recommended that the unit should be used

with Texecom's ran

e of control

anels.

4INS154-4

The following table illustrates how to connect the unit to the Texecom range and

other control panels:

A B C D S

Texecom Control Panel A B C D S

C&K Active 5, Securit BELL + S - 24 TAMPER AUX - ST -

Menvier TS510, 700, 800 BELL 12V BELL TRIG BELL TMP 0V STB

Scantronic 9448 to 9800 +12V BELL TR 0V STR

When connecting the unit to the control panel, it is recommended that wiring should

be connected to the unit first and the control panel second. The unit should then be

initially powered from the control panel. If the tamper circuit is open the siren will

sound for 5 seconds after which it will automatically enter Hold-Off mode and disable

Self-Activate (S/A) on tamper. This will prevent the unit from self-activating as long as

the tamper circuit remains open. An open tamper circuit is indicated by only the

left-hand side LED flashing. Connect the battery by moving the red battery wire from

the “N/C” (No Connect) terminal to the “Battery +” terminal. Fit the outer cover and

secure with the M6 screw(s) provided.

When the outer cover is replaced and the tamper circuit is closed, the LEDs will

alternate rapidly, confirming that the tamper circuit is secure and signalling that S/A

on tamper will be re-enabled within 2 minutes, after which the LEDs will alternate

slowly to signal normal operation. If the tamper circuit is re-opened within the 2

minute period, then Hold-Off mode will be restored.

If the unit is powered up with the tamper circuit closed it will NOT sound for 5

seconds and will NOT enter Hold-Off mode. In order to disable the S/A function,

before the cover is removed, Hold-Off mode should be invoked as for servicing (see

Section 2).

For safety reasons the strobe is disabled during Hold-Off mode.

Hold-Off mode is immediately cancelled when the sounder is activated from the

control panel.

1.3.1 Optional “Battery First” Connection Method

Hold-Off mode automatically cancels when both the tamper circuit is closed and

power is supplied from the control panel. This allows installation engineers to power

the unit from the internal battery and fit the outer cover, knowing that the unit cannot

self-activate until after power has been supplied from the control panel.

If the tamper circuit is closed and the unit is powered by the battery only, the right

LED will flash quickly to signal that the unit cannot self-activate until power has been

supplied from the control panel.

Prolonged “battery first” connection without power from the control panel may cause

permanent damage to the internal battery. Texecom recommend that the unit is

initially powered on battery only for no longer than 24 hours.

INS154-4 5

1.4 Installing Multiple Units

If more than one unit is connected to an installation, the current demand may exceed

the rated current output of the control panel. This can be avoided by selecting the

SCB mode on all but one of the connected units.

1.4.1 SCB Mode

In this mode the unit draws the majority of its sounding current from the built-in

battery rather than from the control panel. Although volume is somewhat reduced,

lowering the current demand on the control panel will enable the connection of

additional sounder units. To select SCB Mode, the unit should first be powered from

the built-in battery by connecting the red battery wire from the “N/C” (No Connect)

terminal to the “Battery +” terminal. The unit will automatically enter Hold-Off mode to

disable Self-Activate (S/A) on tamper, this will prevent the unit from self-activating

until both the tamper circuit is closed and power is supplied from the control panel.

Move the jumper JP1 to the SCB position before the unit is connected to the control

panel.

If the tamper circuit is closed and the unit is powered by the battery only, the right

LED will flash quickly to signal that the unit cannot self-activate until power has been

supplied from the control panel.

The following diagram illustrates how to wire multiple units together:

If the first unit is opened it will self-activate and a tamper will be signalled to the

control panel. If the second unit is opened both units will self-activate and a tamper

will be signalled to the control panel.

When selecting SCB mode the battery must be connected before power is supplied

from the control panel. If multiple unitsare connected to a single control panel

without SCB mode selected, the sounding current may exceed the rated current of

the control panel. If a unit is powered from a control panel with SCB mode selected

but without the battery connected, the unit will not operate correctly due to the lack of

power provided.

The built-in battery will only be partially charged on delivery.

Remove tamper wire from MSW 2 on first unit

and connect to spare core. On second unit

connect spare core into MSW 1.

6INS154-4

1.5 Commissioning

Most control panels have a method of testing the siren and strobe, which should be

utilised for final testing. Failing this, simply arm the system and cause an alarm to

confirm correct operation. Temporarily disconnect the positive supply to the unit at

the control panel to confirm that the sounder self-activates.

The strobe does not self-activate.

Some control panels have an option to select the sounder cut-off time. The unit will

sound for either 15 minutes or for the panel cut-off time, whichever is the shorter.

2. Servicing

CAUTION: BEFORE OPENING THE COVER ALLOW AT

LEAST 3 MINUTES AFTER THE LAST STROBE FLASH

Most control panels have a method of testing the siren and strobe, which should be

utilised. Failing this, simply arm the system and cause an alarm to confirm correct

operation. Temporarily disconnect the positive supply to the unit at the control panel

to confirm that the sounder self-activates.

The strobe does not self-activate.

Some control panels have an option to select the sounder cut-off time. The unit will

sound for either 15 minutes or for the panel cut-off time, whichever is the shorter.

For safety reasons if it is necessary to inspect the unit, the Self-Activate (S/A) on

tamper function should be disabled before the cover is removed. This is achieved by

using the unit’s unique patented engineer Hold-Off mode. This is invoked by

activating and de-activating the strobe three times within 30 seconds. Most control

panels have a method of testing the strobe, which should be utilised. Failing this the

strobe can be manually activated by connecting the S (STRB) wire to 0V at the

control panel. Hold-Off mode is shown to be active with the tamper circuit secure by

the right LED only flashing.

If the tamper circuit is not opened then Hold-Off mode will automatically start to

cancel after 15 minutes, indicated by the LEDs alternating rapidly to signal that S/A

on tamper will be re-enabled within a further 2 minutes.

Once the outer cover is removed the left LED only will flash to indicate that the

tamper circuit is open.

Please note, it cannot be guaranteed that the battery is fully charged on

installation. When commissioning, the unit may require to be powered from

the control panel for a period of time before the battery is sufficiently

charged for self-activation.

INS154-4 7

When the outer cover is replaced, and the tamper circuit is closed, the LEDs will

alternate rapidly, confirming that the tamper circuit is secure and signalling that S/A

on tamper will be re-enabled within 2 minutes, after which the LEDs will alternate

slowly to signal normal operation. If the tamper circuit is re-opened within the 2

minute period, then Hold-Off mode will be restored.

Summary of LED States

Slow flashing LEDs Normal operation

Left LED flashing only Hold-Off active, tamper circuit open

Right LED flashing only Hold-Off active, tamper circuit closed

Fast flashing LEDs Hold-Off active but will cancel within 2 minutes

If Hold-Off mode is invoked but the tamper circuit is not opened within 15 minutes

then Hold-Off will automatically start to cancel, indicated by the LEDs alternating

rapidly for a further 2 minutes.

For safety reasons the strobe is disabled during Hold-Off mode.

Hold-Off mode is immediately cancelled when the sounder is activated from the

control panel.

3. Safety

INSTALLATION AND MAINTENANCE BY

QUALIFIED SERVICE PERSONNEL ONLY

All strobes produce hazardous voltages. However, the unit includes dual circuit safety

interlocks. When the strobe is de-activated it invokes a final flash to discharge the

high voltage. Back-up circuitry guarantees discharge of the high voltage within 3

minutes.

For your own safety be sure to observe the following precautions

when installing and servicing the unit:

•NEVER remove the cover when the strobe is flashing

•WAIT 3 minutes after the strobe stops flashing before removing the cover

•AVOID touching the part of the PCB labelled “Warning High Voltage”

The unit incorporates software which disables the strobe whilst the tamper switch

remains open. This is a safety feature and cannot be disabled.

The piezo drive produces high voltages when the siren is sounding. While not

directly hazardous, these voltages will cause discomfort and should be avoided,

particularly when using tools or a ladder.

The piezo transformer TF1 will be hot during and after sounding. While not directly

hazardous, touching it when hot will cause discomfort and should be avoided,

particularly when using tools or a ladder.

8INS154-4

Failure to observe the following precautions regarding the battery could lead to the

danger of heating, ignition or explosion:

•Do not throw into a fire

•Do not heat

•Do not over-charge

•Do not reverse charge

•Do not short-circuit

•Do not disassemble

•Replace only with the same or

equivalent type

Always observe local regulations when disposing of a battery.

Plastic bags can suffocate - always dispose of packaging carefully.

4. Technical Specification

Environmental

Volume

Azura 360, Tempest: 109dB Peak at 1m (A Weighting, 90°)

Odyssey 1E, 2E, 3E & 4E: 109dB Peak at 1m (A Weighting, 90°)

Odyssey 1, 2, 3 & 4: 115dB Peak at 1m (A Weighting, 90°)

Cut-Off Time: ≤15 minutes

Waterproof Coating: Conformal

Operating Temperature: -25°C (-13°F) to +55°C (+131°F)

Storage Temperature: -25°C (-13°F) to +60°C (+140°F)

EMC Environment: Residential / Commercial /

Light Industrial / Industrial

Electrical

Supply Voltage: 12VDC (nominal)

Current Drain (typical at 12VDC)

Quiescent: 15mA

Strobe: 110mA

Sounder

Azura 360, Tempest: 300mA

Odyssey 1E, 2E, 3E & 4E: 300mA

Odyssey 1, 2, 3 & 4: 425mA

Standby Battery

Type: NiMh Stack

Voltage: 7.2VDC (nominal)

Capacity: 320mAh

Flash Tube: 1Ws

Flash Rate: 1Hz (typical)*†

Discharge Time (≤

≤≤

≤60VDC): ≤180 seconds

Comfort LEDs

Brightness: 100mcd (typical)

Flash Rate (tamper secure): 1Hz alternating (typical)

*The flash rate will reduce to 0.125Hz after flashing for one hour (1 flash every 8

seconds). This is a software feature to reduce power consumption and cannot be

disabled.

† The flash rate may reduce to 0.5Hz for supply voltages less than 12VDC.

INS154-4 9

Physical

Material

Azura 360, Tempest: 3mm polycarbonate

Odyssey 1E, 2E, 3E & 4E: 3mm polycarbonate / 3mm ABS

Odyssey 1, 2, 3 & 4: 3mm polycarbonate

Orientation

Azura 360, Tempest: Vertical or horizontal

Odyssey 1, 1E, 3 & 3E: Vertical

Odyssey 2 & 2E: Horizontal

Odyssey 4 & 4E: Vertical or horizontal

Mounting: Corner mounting points plus central

keyhole(s)

Tamper Detection

Azura 360, Tempest: Wall and lid

Odyssey 1E & 2E: Wall and screw

Odyssey 1, 2, 3 & 4: Wall, screw and lid

Odyssey 3E & 4E: Wall and lid

Dimensions

Azura 360: 319mm x 196mm x 77mm

(12.56"x 7.80"x 3.64")

Tempest: 316mm x 205mm x 89mm

(12.44"x 8.07"x 3.50")

Odyssey 1 & 1E: 318mm x 201mm x 66.5mm

(12.52"x 7.91"x 2.62")

Odyssey 2 & 2E: 382mm x 242.2mm x 76mm

(15.03"x 9.53"x 2.99")

Odyssey 3 & 3E: 315mm x 306mm x 78mm

(12.40"x 12.04"x 3.07")

Odyssey 4 & 4E: 310mm x 196mm x 58.5mm

(12.20"x 7.71"x 2.30")

Packed Weight

Azura 360, Tempest: 1250g (44oz) approx.

Odyssey 1, 1E, 3, 3E, 4 & 4E: 1250g (44oz) approx.

Odyssey 2 & 2E: 1600g (56oz) approx.

Standards

Safety: Conforms to European Union (EU) Low

Voltage Directive (LVD) 73/23/EEC

(amended by 93/68/EEC).

EMC: Conforms to European Union (EU)

Electro-Magnetic Compatibility (EMC)

Directive 89/336/EEC (amended by

92/31/EEC and 93/68/EEC).

Security Specific: Conforms to EN50131-1/PD6662

Grade 3, Env Class IV Requirements

To comply with EU Directives the unit MUST ONLY be connected to a fused

power source (≤5A) supplied from an isolating transformer.

The CE mark indicates that this product complies with the European requirements for

safety, health, environmental and customer protection.

10 INS154-4

5. Warranty

All Texecom products are designed for reliable, trouble-free operation. Quality is

carefully monitored by extensive computerised testing. As a result the Azura 360,

Tempest, Odyssey 1E, Odyssey 2E, Odyssey 3E and Odyssey 4E are covered by a

two year warranty against defects in material or workmanship (details on request).

The Odyssey 1, Odyssey 2, Odyssey 3 and Odyssey 4 are covered by a five year

warranty.

Because the Azura 360, Tempest and Odyssey Series are not complete alarm

systems but only a part thereof, Texecom cannot accept responsibility or liability for

any damages whatsoever based on a claim that a unit failed to function correctly.

Due to our policy of continuous improvement Texecom reserve the right to change

specification without prior notice.

Azura 360, Tempest and Odyssey are trademarks of Texecom Ltd.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Texecom Système de sécurité

Texecom

Texecom Premier Elite 8XP-W Manuel utilisateur

Texecom

Texecom PREMIER 48 Manuel utilisateur

Texecom

Texecom Ricochet Impaq Contact-W Manuel utilisateur

Texecom

Texecom Veritas Excel Master Manuel utilisateur

Texecom

Texecom Premier Elite Impaq Contact-W Manuel utilisateur

Texecom

Texecom PREMIER 640 Manuel utilisateur

Texecom

Texecom Premier Elite Ricochet Kits Manuel utilisateur

Texecom

Texecom Premier 816 Manuel utilisateur

Texecom

Texecom Premier Elite 8XP-W Manuel utilisateur

Texecom

Texecom PrestigeCompact IR Manuel utilisateur

Texecom

Texecom Speech Dialler Manuel utilisateur

Texecom

Texecom Premier Elite Series Manuel utilisateur

Texecom

Texecom Premier Elite 8XP-W Manuel utilisateur

Texecom

Texecom Premier 412 Manuel utilisateur

Texecom

Texecom INS555-3 Manuel utilisateur

Texecom

Texecom Speech Dialler Manuel utilisateur

Texecom

Texecom Premier Elite Impaq Contact-W Manuel utilisateur

Texecom

Texecom Premier Elite 8XP-W Manuel utilisateur

Texecom

Texecom Premier 412 Manuel utilisateur

Texecom

Texecom Premier Elite SmartKey Manuel utilisateur

Texecom

Texecom Premier 412 Mode d'emploi

Texecom

Texecom Premier Elite iProx Manuel utilisateur

Texecom

Texecom Premier 412 Manuel utilisateur

Texecom

Texecom ComGSM Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur