Testrite Visual Charisma XBX Series Manuel utilisateur

Page 1 of 2Version: 2

First start by assembling corners. There are three (3) brackets per corner. All extrusion sections are numbered to identify which

pieces go together, 1 with 1, 2 with 2, etc.

1. Insert the at L brackets with the four (4) set screws into the back of one extrusion segment as shown. Identical bracket with no

holes goes between bracket and the extrusion, as shown in the images below. Lightly screw into place, DO NOT fully tighten.

2. For Bent Corner Bracket: Insert the bent bracket into the same extrusion section. Firmly screw the bracket into place. Take the

mating extrusion piece with matching number. Guide the corner brackets in, then tighten all brackets.

3. Repeat assembly steps for the three remaining corners (not shown).

4. Install white backing graphic (See additional page for detailed instructions).

5. WALL MOUNT OPTION: Drill mounting holes in the frame channel as needed, to align with the EXISTING WALL STUDS. Using an X-acto

blade or hole puncher, puncture or cut small holes into the white backing graphic to match the holes just drilled in the frame, then

mount to the wall (Mounting screws and anchors not provided).Install front graphic (See additional page for detailed instructions).

6. Install the graphic (See additional page for detailed instructions).

NOTE: Model shown below may dier from your model, but assembly instructions remain the same.

Charisma™ LED Single Sided Light Box - XBX Series - Without Lights

6. Graphic Installation

(see next page)

4. Backing graphic Installation (see next

page)

White Backing Graphic

XBX34 shown

Wall Mount Holes

are drilled by

customer at time

of installation.

Screw

2a.

White

Backing

Graphic

2c.

2b.

Bracket A

Bracket B

Bracket A

Bracket B

Page 2 of 2Version: 2

1. To install the backing graphic or front graphic, take the corner with the pull tag on it and press about 6”-10”of silicone into the frame channel (g. 1a).

Repeat for the opposite corner (g. 1b). Repeat for the next corner (g. 1c). Lastly, repeat for the nal corner (g. 1d).

2. After all corners are pressed in, press the silicone into the frame channel at the mid-points on all four sides.

3. Press silicone into frame evenly between the corner and midpoints.

This prevents the graphic from bunching up or stretching too much and will ensure a smooth and tight t.

4. To remove the graphic from the frame, simply pull up on the pull tag.

NOTE: Model shown below may dier from your model, but assembly instructions remain the same.

Charisma™ LED Single Sided Light Box - XBX Series - Without Lights

1. 3.2. 4.

1a. pull tag

1b.

1d.

1c.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Testrite Visual Équipement d'éclairage

Testrite Visual

Testrite Visual Charisma Inside-Out Light Box XSIO Series Manuel utilisateur

Testrite Visual

Testrite Visual SupraSlim SnapFrame SUL Series Manuel utilisateur

Testrite Visual

Testrite Visual XSD Series Manuel utilisateur

Testrite Visual

Testrite Visual Charisma SEG 3D Lit XS Series Manuel utilisateur

Testrite Visual

Testrite Visual Charisma SEG XSL Series Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur