Tenveo VHD Series Manuel utilisateur
Version V3.22(English)
HD Conference Camera
User Manual
Performance Characteristics
Quick Start
Remote Control Button Description
Common Operation Instructions
Camera Menu Set
Troubleshooting
Tech parameters
Product Description
Foreword
Notice
Supplied Accessories
Camera papameters
Interface definition
Installation instructions
Contents
Remote control instructions
Common operation instructions
Menu description
Control interface
Remote control match
Troubleshooting
Maintenance Services
Maintenance services
1
1
1
2
2
3
4
5-6
6-7
8-11
11-12
12
13
13
Warranty card
Warranty card 14-15
------------------------------------
------------------------------------
------------------------------------
------------------------------------
------------------------------------
------------------------------------
Interface diagram 4
------------------------------------
------------------------------------
------------------------------------
------------------------------------
------------------------------------
------------------------------------
------------------------------------
------------------------------------
------------------------------------
------------------------------------
1
Attention
Thanks for choosing our VHD series conference cameras.
Please read this manual carefully before using the product.
1. Foreword
·To avoid damage from stress, violent vibration, soaking during tra-
nsportation, storage and installation.
·Take care of each components of camera during installation, and
install camera at where is affordable enough, to avoid drop or scra-
tches of camera case.
·Handle the camera parts gently, do not squeeze the camera units
hard. Please do not touch the camera lens by hand directly to avo-
id the lens scratched and image quality affected.
·Do not apply excessive voltage. (Use only the specified voltage)
Otherwise, you may get an electric shock or a fire occur.
·Do not aim the camera at the sun or the other high luminous obje-
cts, otherwise it may cause image blurring or lens flare, even cause
permanent damage to the camera.
·Do not clean camera with active chemical or corrosive detergents,
and remove dust or dirt on the surface of the lens with a blower (C-
ommercially available)
·Do not disassemble any camera components, in case of abnormal
operation; contact your authorized dealer or the store where you p-
urchased the product.
(1) HD conference camera (2) DC12V-2A power supply
(3) Ceiling mount (4) Mounting screws
(5) Manual (6) Remote control
(7) USB cable
2. Notice
3. Supplied Accessories
Performance Characteristics
1. Camera technical parameters
2. Camera Parameters
Electric Communication
Operation Surroundings
Physics Installation Method
Input Voltage
Power
Decoder
Horizontal Rotation
Vertical Rotation
Baud
Protocol
Address Set
Operating
Environment
Operating Temp
Rotation Speed
Preset Point
Net-Weight
Image Sensor 1/3”Exmor CMOS 1/3”HD CMOS
2.38Mega pixel
1080P(1920*1080) 720P(1280*720)
USB,SDI,HDMI
1080P/720P
NTSC/PAL
IR remote control supports 9 presets PELCO,Protocol supports 256 presets
-170°~170° -30°~90°
100°/s 80°/s
Product：260*175*180mm
black
51.3°~4.64° 55.5°~3.0° 69.5°~2.7°
3.28Mega pixel
1/3”CMOS
Effective Pixel
HD Format
Focal Length
HD Interface
FOV
Resolution
Signal System
Control parameters
Translation/
Pitching Angle
Translation/
Pitching Speed
Preset
Control Protocol
Control Interface
Common Parameters
Size
Color
lens 10x Optical Zoom 30x Optical Zoom20x Optical Zoom
Spec
DC12V
12W
internal
±170°
120°
38400/9600bps
VISCA/PELCO-D /PELCO-P
0~64
0°~+50°
0~95%
non-condensing
Support desktop,wall mount,ceiling mount
and tripod installation
100°/s
9 remote controls
Pelco Protocol
256
1.46kg
2
f=5.0-50.0mm f=5.35-107.0mm f=4.7-140.0mm
VISCA PELCO-D PELCO-P
RS-232、RS-485
Quick Start
1.SDI 2.HDMI 3.IR Receiver
4.USB 5.RS232 6.RS-485
7.DC 12V
1.Lens
2.Pan&Tilt
3.Stand by indicator
4.Power indicator
5.IR remote indicator
3
1. Interface definition
DC 12V
RS-485IN RS-232 OUT
AB
USBIRSDI
HDMI
① ② ③ ④ ⑤ ⑥ ⑦
3.Installation instructions
2.Interface diagram
(1)Surface Installation
SDI
HDMI
USB
RS-485
DC 12V Output AC 220V Input
VISCA IN
VISCA OUT
Put the camera on the desk flatly, and make sure the camera in
level. If want to put the camera on oblique surface, please m-
ake sure the angle of inclination less than 15 degree for ensu-
re camera pan and tilt working in normal operation.
(2) Ceiling Mount Installation
>
_
15°
_
<
15°
4
Step 1: Mounting the
ceiling bracket
Mounting the bracket
vertically to the ceiling
with screws.
Step 2: Install the camera
Rotate the camera clockwise
to install it.
Screw port
Ceiling bracket
(This side to the ceiling.)
Ceiling
DC 12V
RS-485IN RS-232 OUT
AB
USBIRSDI
HDMI
5
Remote Control Button Description
(1)Remote control launch window
(2)【POWER】Standby button, pressing it, camera
goes into standby mode; pressing again, camera go-
es power on.
(3)【P/T Reset 】Camera pan/tilt reset function sa-
me with⑧（P/T RESET）
(4)【CAMERA SELECT】Choose the camera number
that needed to control, to correspond the dial-up code
on the back of camera;
(5)【POSITION】Preset position setup keys, include
【PRESET】and【RESET】.
(6)【UP】： Camera rotating horizontally in regular
installed direction
(7)【DOWN】： Camera rotating horizontally in
reversed installed direction
(8)【PAN-TILT】【 PAT-TILT】Camera rotation control
key: press this button and move by the arrow direction,
press
Press【HOME】to back to the center of vertical and
horizontal position.
(9)【Camera Pan/Tilt Reset 】： Camera Pan/Tilt reset ；
(10) MENU.
(11) Slow zoom key
【Zoom SLOW+】T：Zoom in at low speed
【ZOOM SLOW-】W：Zoom out at low speed
(12) Fast zoom key
【ZOOM FAST +】： Zoom in at fast speed
【ZOOM FAST -】： Zoom out at fast speed
(13) Manual focus mode
【MANUAL FOCUS】： Start manual focus function
【FAR】： Manually far focus button, clearer for the
distant objects, loose finger to stop.
【NEAR】： Manually near focus button, clearer for
the nearby objects, loose finger to stop.
(14)【AUTO FOCUS】： Auto focusing button
(15)【L/R DIRECTION/SET】： Not applicable for this model.
14
13
15
12
7
10
1 2 3
12 3
45 6
789
PRESET
0RESET
CAMERA SELECT
STD REV
POSITION
UP
DOWN
HOME
PAN-TILT
MENU
PT/RESET
ZOOM
SLOW
+
-
ZOOM
FAST
+
-
FAR
NEAR
MANUAL
FOCUS
L/R
SET AUTO
FOCUS
6
Common Operations Introductions
1. Camera Select
Refer to the dial-up at the back of camera and choose
camera address number that you want to control（1-3）。
2. Camera Direction Control
*Note: Press direction key to move the camera.Press the
direction key when you need to change the angle. If you
want to move the camera slowly, just click the direction
key; If you want to move the camera fast at a large scale,
just long-press the button.
3. Camera Focusing Mode Control
【AUTO】Switch the focus mode to AUTO
【MANUAL】Switch the focus mode to MANUAL
【FAR】Far focus manually
【NEAR】Near focus manually
Turning up
Turning down
Turning to left
Turning to right
1 2 3
CAMERA SELECT
HOME
FAR
NEAR
MANUAL
FOCUS AUTO
FOCUS
★Attentions for Remote Control
1. If remote control doesn't work, please replace batteries.
2. If there is an object between remote control and speci -
alized remote control sensor, the camera will not work. -
Please make sure the remote control is aimed at the sen -
sor which in front of the camera when controlling it.
7
4. Camera Zoom Control
Press any one of the 4【ZOOM】
to make the zoom functioning.
5. Back Light
The subject will become dark when there is a
light source behind it, press【BACK LIGHT】
to use back light shooting function. To cancel,
press【BACK LIGHT】again.
12 3
45 6
789
PRESET 0RESET
STD REV
POSITION
B-LIGHT
ZOOM
SLOW
+
-
ZOOM
FAST
+
-
6. Preset Setup,Call,Cancel
(1) Reserve Preset: Press【PRESET】
then press one of the number（1-9）to
reserve a preset that correspond to the
NUMBER.
*Note: you can setup 9 presets at most by the remote control.
(2) Call Preset: Press the NUMBER（1-9）directly to call the-
reserved preset.
*Note: It won’ t work if there’ s no preset reserved in the cor-
responded number.
(3) Remove Preset: Press【RESET】, then press one of the-
number（1-9）to remove a preset that correspond to the NU-
MBER.
8
Camera Menu Setup
Operate remote control, press【MENU】to enter main menu
of video camera;
Menu Destription
HDMI output: Support 1080P60/50/30/25, 720P60/50, 1080i 60/50.
Mirror: Support Off /Left/Right/Up/Down image adjust.
1.Level I Menu - MAIN MENU：
2. Level II Menu - Image:
Main Menu
Image
->
Diaplay
->
Lens
->
System
->
Image
Exposure
Wb
ImageE.n
HDMI Output 1080P50
Mirror Off
Autres manuels pour VHD Series
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Tenveo Caméra IP
