Tennant T7 Manuel de formation

IB 340756 (02- 2019) 1

No. 340756

Machine: T7, SSR

Published: 02-2019

Rev. 02

INSTRUCTION BULLETIN

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individual parts and will save the cost of ordering an entire kit.

NOTE:Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 9000145

SYNOPSIS / PROBLEM:

This kit contains the parts needed to install a 800 mm squeegee onto the T7/SSR model scrubbers.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 1 hour)

PREPARATION:

1. Stop machine on a clean level surface.

2. Raise the scrub head to the raised position.

3. Turn off the machine and remove the key.

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, and turn off the

machine.

INSTALLATION:

1. Remove the vacuum hose from the rear

squeegee assembly. Refer to Fig. 8.

2. Remove the knobs holding the rear squeegee

assembly onto the lower squeegee channel

arm. Refer to Fig. 1.

Lower squeegee

channel arm

FIG. 1

3. Remove the rear squeegee assembly from the

machine.

NOTE: For the remainder of this Instruction Bulletin,

refer to Fig. 8 for part locations and orientation of

parts on the squeegee assembly.

4. Use the provided hex screws (8), flat washers

(9), sleeves (10), and hex nuts (11) to install a

bumper wheel (7) onto each end of the new

squeegee frame (1). Refer to Fig. 2.

FIG. 2

IB 340756 (02- 2019)2

5. Use the two provided star knobs (3) to install the

new squeegee retainer plate (2) onto the

squeegee frame (1). Do not tighten star knobs.

Refer to Fig. 3.

FIG. 3

6. Install the new front squeegee blade (4) onto the

squeegee retainer plate (2). Be sure the holes in

the front squeegee blade are hooked onto the

squeegee retainer plate tabs. Refer to Fig. 4.

FIG. 4

7. Slightly tighten the two star knobs (3). Refer to

Fig. 3.

8. Install the new rear squeegee blade (5) onto the

squeegee retainer plate (2). Be sure the holes in

the rear squeegee blade are hooked onto the

squeegee retainer plate tabs. Refer to Fig. 5.

FIG. 5

9. Slide the squeegee strap assembly (6) into the

squeegee frame (1). Seat the squeegee strap

assembly flanges inside the retainers on

squeegee frame. Refer to Fig. 6.

FIG. 6

10. Tighten the squeegee strap assembly (6)

tension latch. Refer to Fig. 7.

FIG. 7

IB 340756 (02- 2019) 3

11. Tighten the star knobs (3) to secure the

squeegee retainer plate (2) into place inside the

squeegee frame (1). Refer to Fig. 8.

12. Use the two remaining star knobs (3) to install

the squeegee assembly onto the lower

squeegee channel arm. Refer to Fig. 8.

13. Install the vacuum hose onto the rear squeegee

assembly. Refer to Fig. 8.

14. Test machine to ensure the rear squeegee

functions properly.

Lower squeegee

channel arm

Vacuum hose

FIG. 8

IB 340756 (02- 2019)4

Bill of Materials for Kit, CI, Squeegee [800 mm]- 9000145

Ref.

Tennant

Part No. Description Qty.

o9000145 )Kit, CI, Squeegee [800 mm] 1

Y1 1012964 Frame, Sqge, 800mm 1

Y2 1013395 Plate Wldt, Sqge, Retainer, 800mm 1

Y3 1074204 Knob, Star, 2.75D 4Ear 1.1L M8 X 1.25 Thru, Y (Yellow) 4

Y4 390923 Blade, Sqge, Front, 800mm Linatex, 41.5L 1

Y5390922 )Blade, Sqge, Rear, 800mm Linatex [44.0L] 1

Y6 1013974 Strap Assy, Sqge, 800mm 1

Y7 1010560 Wheel, Bmpr, 80D X 25W, Non- marking 2

Y8 09011 Screw, Hex, M8 X 1.25 X 30, SS 2

Y9 140027 Washer, Flat, 0.35B 0.75D .04, SS 4

Y10 222460 )Sleeve, P/M, 0.496D 0.318B 0.50L 430SS 2

Y11 08713 Nut, Hex, Lock, M8 X 1.25, NL, SS 2

TENNANT COMPANY

P. O. Box 1452

Minneapolis, MN 55440-1452

Autres manuels pour T7

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Tennant Scrubber

Tennant

Tennant 7100 Manuel utilisateur

Tennant

Tennant 510E Manuel de formation

Tennant

Tennant 5100 Manuel du produit

Tennant

Tennant T591 Manuel utilisateur

Tennant

Tennant T3 Manuel utilisateur

Tennant

Tennant 5100 Manuel du produit

Tennant

Tennant Nobles 3301 Manuel utilisateur

Tennant

Tennant ec H2O NanoClean T350 Instructions d'utilisation et d'installation

Tennant

Tennant T5 Manuel utilisateur

Tennant

Tennant T16 Manuel utilisateur

Tennant

Tennant T16 Manuel de formation

Tennant

Tennant 2100 Instructions d'installation et d'entretien

Tennant

Tennant T12 Manuel utilisateur

Tennant

Tennant M30 Manuel utilisateur

Tennant

Tennant T12 Manuel de formation

Tennant

Tennant 7100 Manuel utilisateur

Tennant

Tennant T20 Gas Manuel utilisateur

Tennant

Tennant T981 Manuel utilisateur

Tennant

Tennant T981 Manuel utilisateur

Tennant

Tennant T7AMR Manuel utilisateur

Tennant

Tennant 800 Manuel utilisateur

Tennant

Tennant T291 Manuel utilisateur

Tennant

Tennant T20 LPG Manuel utilisateur

Tennant

Tennant CS5 Manuel d'utilisation

Manuels Scrubber populaires d'autres marques

Olympus

Olympus M200H Manuel utilisateur

Clarke

Clarke BEXT 100H Manuel d'installation et d'exploitation

JOHNY VAC

JOHNY VAC JVC70BCT Manuel utilisateur

RCm

RCm Elan Series Manuel

Kärcher

Kärcher B 120 W Manuel utilisateur

Truvox

Truvox Orbis MotorScrubber 20 Manuel utilisateur

Numatic

Numatic TTB 4045/100 Manuel utilisateur

U.S. Products

U.S. Products PEX 500-C-TICK Mode d'emploi

Mclennan

Mclennan C510 Manuel utilisateur

Columbus

Columbus ARA 66 BM 100 Manuel utilisateur

Numatic

Numatic TTV 678G / 300T Manuel utilisateur

American-Lincoln

American-Lincoln 505-945 Manuel utilisateur

FIORENTINI

FIORENTINI ET 65-75 Manuel utilisateur

Floorpul

Floorpul ruby 48 blt Guide de l'utilisateur

Onyx

Onyx RX-34 Manuel utilisateur

Dustbane

Dustbane Hurricane 400 Manuel utilisateur

Sana

Sana EUJ-702 Manuel utilisateur

REMS

REMS Twist Manuel utilisateur