Tennant T2 Manuel utilisateur
ENGLISH
Tennant T2 (08--11) 15
MACHINE MAINTENANCE
To keep the machine in good working condition, follow
the machine maintenance procedures.
WARNING: Electrical Hazard. Disconnect
Battery Cables Before Servicing Machine.
DAILY MAINTENANCE
1. Drain and rinse out the recovery tank (Figure 34).
FIG. 34
2. Remove the debris tray and empty (Figure 35)
FIG. 35
3. Remove and clean the float shut--off screen located
in the recovery tank (Figure 36).
FIG. 36
4. Drain the solution tank (Figure 37)
FIG. 37
5. Remove the pad/brush and clean. Rotate pad or
replace when worn (Figure 38).
FIG. 38
6. Wipe the squeegee blades clean (Figure 39).
When machine is not in use, raise squeegee
assembly off floor or hang on storage bracket.
FIG. 39
ENGLISH
16 Tennant T2 (08--11)
7. Check the condition of the squeegee blade wiping
edge (Figure 40). Rotate blade if worn.
(See SQUEEGEE BLADE REPLACEMENT)
FIG. 40
8. Clean the machine with an all purpose cleaner and
damp cloth (Figure 41).
FOR SAFETY: When cleaning machine, do not
power spray or hose off machine. Electrical
malfunction may occur.
FIG. 41
9. Inspect the condition of the scrub head skirt,
replace if worn or damaged (Figure 42).
FIG. 42
10. Recharge the batteries after a total of 30 minutes
of use or more (Figure 43). (See CHARGING
BATTERIES).
FIG. 43
MONTHLY MAINTENANCE
1. Remove the solution tank filter from underneath the
machine and rinse out the screen (Figure 44).
Make sure the solution tank is empty before
removing filter.
FIG. 44
2. Lead Acid Batteries: Clean the battery tops to
prevent corrosion (See BATTERY
MAINTENANCE).
3. Check for loose battery cable connections.
4. Inspect and clean the recovery tank cover seal
(Figure 45). Replace if damaged.
FIG. 45
ENGLISH
Tennant T2 (08--11) 17
5. Lubricate all pivot points and rollers with silicone
spray then coat with a water resistant grease to
maintain smooth operation.
6. Check the machine for loose nuts and bolts.
7. Check the machine for leaks.
MOTOR MAINTENANCE
Contact an Authorized Tennant Service Center for
carbon brush replacement.
Carbon Brush Replacement Hours
Vacuum Motor 750
Brush Motor 750
WARNING: Electrical Hazard. Disconnect
Battery Cables Before Servicing Machine.
SQUEEGEE BLADE REPLACEMENT
Each squeegee blade has four wiping edges. When the
blades become worn, simply rotate the blades
end-for-end or top-to-bottom for a new wiping edge.
Replace blade if all four edges are worn.
1. Remove the squeegee assembly from the machine.
2. Loosen the band clamp and remove the band from
the squeegee assembly (Figure 46).
FIG. 46
3. Remove and rotate the rear blade to a new wiping
edge. (Figure 47).
FIG. 47
4. Remove the thumb screws from the front blade and
rotate blade end--for--end (Figure 48).
NOTE: Use the 5--slot edge use on VCT flooring (vinyl
composite tile) and the 3--slot edge on grouted tile
floors.
FIG. 48
BATTERY MAINTENANCE (Lead Acid Batteries)
1. Check battery fluid level frequently to prevent
battery damage. The fluid should be at the level
shown (Figure 49). Add distilled water if low. DO
NOT OVERFILL, the fluid may expand and
overflow when charging.
Before Charging After Charging
CORRECT BATTERY FLUID LEVEL:
FIG. 49
WARNING: Fire Or Explosion Hazard.
Batteries Emit Hydrogen Gas. Keep Sparks And
Open Flame Away. Keep Battery Compartment
Open When Charging.
ENGLISH
18 Tennant T2 (08--11)
2. Clean the batteries to prevent battery corrosion.
Use a scrub brush with a mixture of baking soda
and water (Figure 50).
FOR SAFETY: When cleaning batteries, wear
protective gloves and eye protection. Avoid
contact with battery acid.
FIG. 50
TRANSPORTING MACHINE
When transporting the machine by use of trailer or
truck, be certain to follow the tie--down procedure
below:
1. Raise the scrub head and hang squeegee
squeegee on storage bracket.
2. Load the machine using a recommended loading
ramp.
3. Position the front of machine up against the front of
the trailer or truck and lower the scrub head.
4. Place a block behind each wheel to prevent the
machine from rolling.
5. Secure machine with tie--down straps. Machine is
equipped with two tie--down brackets (Figure 51).
FOR SAFETY: When transporting machine, use a
recommended ramp when loading/unloading
into/off truck or trailer. Use tie--down straps to
secure machine to truck or trailer.
STORING MACHINE
1. Charge the batteries before storing. Never store
the machine with discharged batteries.
2. Drain and rinse the tanks thoroughly.
3. Store the machine in a dry area with the squeegee
and scrub head in the up position.
4. Open the recovery tank cover to promote air
circulation.
ATTENTION: Do not expose machine to rain, store
indoors.
5. If storing machine in freezing temperatures, follow
the FREEZE PROTECTION instructions below.
FREEZE PROTECTION
1. Drain the solution tank and recovery tank of all
water.
2. Empty the solution tank filter located under the
machine (Figure 51).
FIG. 51
3. Pour 1 gallon/4 liters of recreational vehicle (RV)
antifreeze into the solution tank at full strength.
Do not dilute.
4. Turn the machine power on and operate the
solution flow system. Turn the machine off when
the red RV antifreeze is visible.
Autres manuels pour T2
2
Autres manuels Tennant Scrubber
Tennant
Tennant 7200 Manuel utilisateur
Tennant
Tennant T7 Manuel utilisateur
Tennant
Tennant Nobles 3301 Manuel utilisateur
Tennant
Tennant M20 Manuel utilisateur
Tennant
Tennant T581 Manuel utilisateur
Tennant
Tennant T20 LPG Manuel utilisateur
Tennant
Tennant T17 Series Manuel de formation
Tennant
Tennant 8300 Manuel de formation
Tennant
Tennant F 170 Manuel utilisateur
Tennant
Tennant T591 Manuel utilisateur
Tennant
Tennant 7200 Manuel de formation
Tennant
Tennant CS16 Manuel utilisateur
Tennant
Tennant 5400 Manuel du produit
Tennant
Tennant IPC PW-H61 Manuel utilisateur
Tennant
Tennant M17 Series Manuel de formation
Tennant
Tennant Nobles T350 Manuel utilisateur
Tennant
Tennant M17 Series Manuel utilisateur
Tennant
Tennant T20 LPG Manuel utilisateur
Tennant
Tennant 5280 Manuel utilisateur
Tennant
Tennant 5400 Manuel utilisateur
