Tempur-Pedic RF502A Manuel utilisateur
User Manual of RF502A
1/ 4
Item
1.1 ZG button⑾
Click the ZG button, the actuator moves to ZG position, stop when click any button during the
movement;
Press and hold the ZG button for 5s, timer LED of remote flashes, the control box records
current position as ZG position;
When in the process of movingto memory positions, the head and foot actuatorsmove first,
then the tilt and lumbar actuators move;
1.2 AntiSnore button⑻
Click AntiSnore button, actuators move to AntiSnore position, stop when click any button
during movement；
Press and hold AntiSnore button for 5s, timer LED of remote flashes, the control box records
current position as AntiSnore position;
When in the process of moving to memory positions, the head and foot actuators move first,
then the tilt and lumbar actuators move;
1.3 Head up⑷
Press and hold HEAD UP button of remote, head actuator moves out, stop when
released；
1.4 Head down⑺
Press and hold HEAD DOWN button of remote, head actuator moves in, stop when released；
1.5 Foot up⑹
Pressa and hold FOOT UP button of remote, foot actuator moves out, stop when released;
2/ 4
1.6 foot down⑼
Press and hold FOOT DOWN button of remote, foot actuator moves in , stop when released；
When moving to flat position, lumbar actuator and tilt actuator move first, after 500ms, head
andfoot actuators start moving;
1.7 Flat⒀
Click FLAT button, the bed goes flat, stop when click any button during the process of going
flat；
1.8 Massage head⑴
Click MASSAGE HEAD button, head massage motor switches massage intensity, massage
intensityswitches among 0-1-2-3；
1.9 Massagefoot⑶
Click MASSAGE Foot button, head massage motor switches massage intensity, massage
intensityswitches among 0-1-2-3；
1.10 Massagemode⑵
Click MASSAGE Mode button to switch the massage mode.
1.11 Under bed light⑸
Click the under bed light button, the under bed light switch its on/off state; After the under bed
light opens,if do not manually close, itwill automatically turnoffafter 5 minutes;
1.12 Memory position ⑽⑿
Click memory position to move the actuator to thememory position.
The product is the remote control of the bed, and the matching model is MC120NM.
FCC ID:2AK23MC120NM
RF Function:2.4G SRD
Operating Band/Frequency:2403-2480MHz
Antenna Type:PCB antenna
Maximum Antenna Gain:1dBi
Manufacturer:Keeson Technology Corporation Limited
Address:No. 195, Yuanfeng East Road, Wangjiangjing, Xiuzhou District,
Jiaxing City, China 314000
3/ 4
FCC Statement
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
ISED RSS Warning/ISED RF Exposure Statement
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt
RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
FCC Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure requirment. The device can be used in
portable exposure condition without restriction.
ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.The
device has been evaluated to meet general RF exposure requirement.
Le matériel est conforme aux limites de dose d'exposition aux rayonnements énoncés pour fac un autre
environnement.ce dispositif a été évalué à satisfaire l'exigence générale de l'exposition aux rf.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Table des matières
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
