Teletek electronics Natron WSS Manuel utilisateur

ATTENTION: Read carefully this installation Instructions before installing the device!

This manual is subject to change without notice!

1. General Description

Natron WSS is a wireless addressable fire alarm sounder with strobe, designed for operation with Natron series

wireless expander modules*. The fire sounder is equipped with 360˚visible strobe LED indication and a built-in

sounder for signalization in case for announcing of events –fire alarm and finding the place of installation. The

operation of the strobe and sounder is programmed from the sounder’s menus (addressable panel or expander

module). Natron WSS is a VAD (Visual Alarm Device) compatible with a deep wireless fire base for wall

mounting. For prevention of unauthorized disassembling or removing, the sounder can be locked to the fire base.

The fire sounder is equipped also with a tamper switch for self-protection of the box. Natron WSS is designed for

indoor installation.

* Refer to the installation manuals of Natron WE-C, Natron WE-A and Natron WE-A/C wireless expander modules for detailed

information about the programming menus and other details.

2. Technical Specifications

Communication range with expander module ...................1500m

Battery power supply..........................................................4 x CR123A 3V

Battery life...........................................................................~8 years

Radio frequency .................................................................868MHz

Communication type...........................................................Bidirectional

Communication Protocol....................................................NATRON TTE

Radio signal modulation type.............................................GFSK

Number of frequency channels ..........................................6 pair channels

Radiated power ..................................................................≤ 20 mW

Receiver category (EN300-220-1) .....................................1.5

Trace attenuation (during the installation)..........................≥ -90dBm

Test transmission message period ....................................300s

Number of tone types (selectable from panel/module)......32

Power volume (main tone type 27):

- Low volume..............................................................~80dB (A) ±6dB@1m

- High volume .............................................................~92dB (A) ±5dB@1m

Power volume (other tone type):

- Low volume..............................................................~75-85dB ±3dB@1m

- High volume .............................................................~80-95dB ±3dB@1m

Operation temperature .......................................................-10°C to +55°C

Related humidity resistance (no condensation).................(93±3)% @ 40°С

Enclosure box type, color...................................................SAN, white transparent

Dimensions (including base)..............................................Ø116x90mm

Protection ...........................................................................IP31

Weight (including base and batteries)................................372g

Mounting.............................................................................Wall, VAD device, Indoor use

Standards ...........................................................................EN 54-3; EN 54-23; EN 54-25

Natron WSS

Wireless addressable

fire alarm sounder and

strobe

Teletek Electronics JSC

Address: 2 Iliyansko Shose Str,

1220 Sofia, Bulgaria

2918

DoP No: 223

EN 54-3:2001+A2:2006

EN 54-23:2010

EN 54-25:2008

Type A; Open class

A-weighted sound level

diagram

3. Installation Place and Mounting

Attention:

For optimum operation,

plan to ensure at least

2m distance between two

Natron expander

modules and the same

minimal distance

between each device and

the expander module.

Wireless fire base –Dimensions and mounting

Dimensions of Natron WSS –

Wireless fire base and sounder

Disassembling

Locking the sounder to the base

Assembling

Unlocking the sounder

from the base

4. PCB Elements

The PCB of Natron WSS is factory mounted and is accessible after disassembling the sounder from the wireless

fire base –see item 3.

1 –Enroll button. The button is used for the following

actions:

- Enrolling the sounder to the expander module.

- Checking the signal strength.

- Reset the sounder.

2 –Power Batteries CR123A 3V

Attention: Use only batteries from the same type!

3 –Bi-color operation LED (green/red). The LED is used

for following the actions during enrollment, reset and

checking the signal strength.

4 –Tamper switch

5. Description of Tone Types

Natron WSS supports 32 different alarm tone types. The tone type is set from the programming menus of the

expander module (conventional fire alarm systems) or programming the sounders mode in the menus of the

addressable fire alarm panel. The sound volume level varies with the tone type selected.

The main tone type of Natron WSS is 27.

Tone

Tone Type

Tone Description/Application

970Hz

800Hz/970Hz @ 2Hz

800Hz - 970Hz @ 1Hz

970Hz 1s OFF/1s ON

970Hz, 0.5s/ 630Hz, 0.5s

554Hz, 0.1s/ 440Hz, 0.4s (AFNOR NF S 32 001)

500 - 1200Hz, 3.5s/ 0.5s OFF (NEN 2575:2000)

420Hz 0.625s ON/0.625s OFF

(Australia AS1670 Alert tone)

500 - 1200Hz, 0.5s/ 0.5s OFF x 3/1.5s OFF

(AS1670 Evacuation)

550Hz/440Hz @ 0.5Hz

970Hz, 0.5s ON/0.5s OFF x 3/ 1.5s OFF (ISO 8201)

2850Hz, 0.5s ON/0.5s OFF x 3/1.5s OFF (ISO 8201)

1200Hz - 500Hz @ 1Hz (DIN 33 404)

400Hz

550Hz, 0.7s/1000Hz, 0.33s

6. Enrolling to Expander Module

1. Remove the wireless fire base to access the PCB with the batteries compartment. If the device is not new,

perform reset as described in item 7.

2. Enter in programming mode of the Natron expander module. Select ADD DEVICE menu and press ENTER

button. A list with already enrolled devices is shown on the screen with an order number and type of the device.

3. Scroll down to find a free address to enroll the sounder. Every free address is labeled as EMPTY.

4. Press ENTER button. Message SEARCHING >>> (arrows are blinking) appears on the screen showing that

the module is scanning for signals from a wireless device in its covering range.

Note: If there is no signal from the device in 2-minute period, the expander module will exit automatically the

programming mode.

5. Power on the sounder. If the device is new just remove the protective folio from the batteries –the

enrolling process starts automatically. If the device is powered and reset - single press the ENROLL

button. The operation LED (item 4, position 3) starts flashing in red.

6. In case of successful enrolment, the operation LED flashes 3 times in green and message DONE appears for a

while on the screen of the module. The sounder is added to the list as WSS type.

7. Test the signal strength between the sounder and the expander module. Single press the ENROLL button and

wait for the operation LED indication:

Tone

Tone Type

Tone Description/Application

750Hz

2400Hz

660Hz

660Hz 1.8s ON/1.8s OFF

660Hz 0.15s ON/0.15s OFF

510Hz, 0.25s/ 610Hz, 0.25s

800/1000Hz 0.5s each (1Hz)

250Hz - 1200Hz @ 12Hz

500Hz - 1200Hz @ 0.33Hz

2400Hz - 2900Hz @ 9Hz

2400Hz - 2900Hz @ 3Hz

2500Hz (main sound frequency)

800Hz - 970Hz @ 100Hz

800Hz - 970Hz @ 9Hz

800Hz - 970Hz @ 3Hz

800Hz, 0.25s ON/1s OFF

600Hz –1100Hz, 2.6s/0.4s OFF

- 3 flashes in green –excellent signal strength;

- 3 flashes in orange –good signal strength, but, if possible, change the place of installation;

- 3 flashes in red –poor signal strength and it is obligatory to change the place of installation.

You can also check the signal quality for the device in DEVICE RSSI menu of the module - item 8.

8. If the signal quality and strength are excellent or good, you can proceed with mounting.

9. Use appropriate fixing elements to mount the wireless fire base to the place of installation. Follow the

instructions in item 3 to lock the sounder to the fire base if this is needed.

10. Place the sounder in the base as observe the two short marks to coincide. Move the sounder’s body up to

hide the marks. Rotate the sounder on clock side until a click is heard.

7. Reset of the Sounder

If the sounder is not new, you have to reset it before enrolment to the expander module. Check the batteries

condition. It is recommended to change all of them with a brand new.

To reset the Natron WSS, power it on with the batteries and after that press and hold ENROLL button for 5-7

seconds. The reset is complete when the operation LED flashes 3 times in green, followed from 1 long flash in

red and 1 long flash in green. Next pressing of ENROLL button will start the enrolment procedure to expander

module.

8. Checking the Signal Quality (RSSI)

The quality of the signal between the sounder and the expander module is checked at DEVICE RSSI menu of the

module. The signal quality is assessed in [dB].

1. Enter in programming mode of the module. Scroll to menu DEVICE RSSI and press ENTER button. A list with

present enrolled devices is shown on the screen with an order number and type of the device.

2. Find in the list the sounder number.

3. Press ENTER button. Refer to the table below to read the signal quality on the screen:

Signal quality

Level RSSI

Description

< -90 dB

Loss

Bad signal or no connection.

-90 ÷ -70 dB

Good

The signal is satisfactory but needs improvement. It is recommended to change the

installation place of the device.

> -70 dB

Excellent

Excellent signal.

4. You can exit the menu at any time with pressing CANCEL button.

9. Finding the Sounder Installation Place and Test

This is a procedure that helps the engineer to find the exact location of every wireless device in the fire

installation and test the connection with module.

1. Enter in programming mode of the module. Scroll to menu FIND DEVICE and press ENTER button. A list with

present enrolled devices is shown on the screen with an order number and type of the device.

2. Find in the list the sounder number which you want to locate in the fire installation.

3. Press ENTER button. Message FINDING >>> (arrows are blinking) appears on the screen showing that the

module is scanning for signals from the selected wireless device. The message will change for a while to

FINDING DONE in case of success.

4. The sounder will respond with active strobe and short sound signals.

5. The module will exit automatically the finding procedure after 70-80 seconds. You can also stop the procedure

at any time with pressing CANCEL button.

10. Replacing Batteries

It is recommended to change the batteries after 8 years of operation regardless of their indicated discharge level.

Always use only batteries approved by the manufacturer - Panasonic CR123A 3V or other with similar

characteristics. Attention: After indication from the panel/expander module for low battery of a device, the user/

installer must replace the discharged batteries with new within one month. The remaining shelf time of the new

batteries must not be less than 6 years.

1. Disable the sounder operation to avoid fault messages.

2. Disassemble the sounder as described in item 3.

3. Remove the old batteries and place the new as observe the +/- polarity.

4. Assemble the sounder back in place.

5. Enable the sounder operation.

6. Check the signal quality in DEVICE RSSI menu of the expander module.

7. Test the sounder operability.

CAUTION: Do not expose used batteries to fire, hot ovens, or mechanical crushing/cutting as this can result in an explosion.

Exposing batteries to extremely high environmental temperatures or low air pressure can result in explosion or the leakage of

flammable liquid or gas.

DISPOSAL: Follow local regulations regarding disposal of the batteries.

18021226, RevB, 07/2023

Table des matières

Autres manuels Teletek electronics Alarme incendie

Teletek electronics

Teletek electronics SF300 Manuel utilisateur

Teletek electronics

Teletek electronics SensoIRIS BSOU IS Manuel utilisateur

Teletek electronics

Teletek electronics SensoIRIS T110 IS Manuel utilisateur

Teletek electronics

Teletek electronics SF50 Manuel utilisateur

Teletek electronics

Teletek electronics iRIS8 Manuel du propriétaire

Teletek electronics

Teletek electronics SensoIRIS MCP150PR Manuel utilisateur

Teletek electronics

Teletek electronics SensoIRIS T110 IS Manuel utilisateur

Teletek electronics

Teletek electronics SensoIRIS BSOU Manuel utilisateur

Teletek electronics

Teletek electronics TTE Combo Manuel utilisateur

Teletek electronics

Teletek electronics SensoMAG F10 Manuel utilisateur

Teletek electronics

Teletek electronics SensoIRIS BSOU Manuel utilisateur

Teletek electronics

Teletek electronics SensoIRIS WSST Manuel utilisateur

Teletek electronics

Teletek electronics SensoMAG F10B Manuel utilisateur

Teletek electronics

Teletek electronics IRIS Instructions de montage

Teletek electronics

Teletek electronics SensoMAG F10 Manuel utilisateur

Teletek electronics

Teletek electronics SensoMAG B12L/U Manuel utilisateur

Teletek electronics

Teletek electronics SIMPO Guide d'installation

Teletek electronics

Teletek electronics SensoIRIS WSOU Manuel utilisateur

Teletek electronics

Teletek electronics SensoMAG MRB50 Manuel utilisateur

Teletek electronics

Teletek electronics Natron MCP Manuel utilisateur

Manuels Alarme incendie populaires d'autres marques

Zeta Alarm Systems

Zeta Alarm Systems INFINITY ID2 Manuel utilisateur

System Sensor

System Sensor 22051TLE-RF-26 Manuel utilisateur

Pittway

Pittway Notifier AM2020 Manuel utilisateur

Ampac

Ampac ZoneSense Manuel utilisateur

Kidde

Kidde VM-1 Manuel du produit

LST

LST SIM016-3 Manuel utilisateur

Fireboy- Xintex

Fireboy- Xintex FBD-MZ Instructions originales

bolid

bolid S2000-IP-03 Manuel utilisateur

GST

GST DI-9204 Manuel utilisateur

E2S

E2S BExTBG05D Manuel utilisateur

Notifier

Notifier UZC-256 Manuel utilisateur

Fire-Lite Alarms

Fire-Lite Alarms MS-2 Manuel utilisateur

Siemens

Siemens FDOOT221 Manuel utilisateur

hyfire

hyfire HY5000 Series Manuel utilisateur

FlameStop

FlameStop PFSIFP8 Manuel utilisateur

Radionics

Radionics Radionics 9124 Manuel utilisateur

UniPOS

UniPOS FD 7120 Manuel utilisateur

FIREWOLF

FIREWOLF FW-C01224 Manuel utilisateur