TELEREADER CWR-685E Manuel utilisateur

CWR-685E

SERVICE MANUAL

Digitization and editing of text and images by DC7XJ, August 2019

Table of Contents

Page

1. Int oduction (Concept and cautions of t oubleshooting) 4

2. Gene al desc iption

2.1 Composition 5

2.2 Flow of signal 6

2.3 Cont ol of SW OUT REMOTE 7

2.4 Flow of signal in t ansmission 7

3. Input/Output actions

3.1 Actions of switches 8

3.2 Actions of exte nal cont ol signal output po ts 9

3.3 Actions of CW audio demodulato 10

3.4 Change of CW t ansmission speed 11

4. T oubleshooting

4.1 T ouble of built-in display 12

(A) No display 12

(B) Fluctuating display 14

4.2 T ouble of CRTC block 16

4.3 T ouble of compute block 19

4.4 T ouble in CW t ansmission 20

4.5 T ouble in CW eception 20

4.6 T ouble RTTY 21

5. Desc iption of MODEM p inted ci cuit boa d pe fo mance

5.1 Demodulato 21

5.2 Modulato 22

5.3 Baud ate clock unit 22

5.4 MODEM p inted ci cuit boa d block diag am 24

6. T oubleshooting of MODEM p inted ci cuit boa d

6.1 Demodulato 25

6.2 Modulato 28

6.3 Baud ate clock unit 29

7. Keyboa d t oubleshooting (KB-685E, KB6850)

7.1 T oubleshooting flow cha t of keyboa d (PCB No. 820226-1) 30

7.2 List of keyboa d output codes 32

8. Desc iption of fo me MODEM boa d 33

9. Pa ts list 35

10. Attached d awings

(1) Block diag am 38

(2) Keyboa d ci cuit diag am 39

(3) Built-in CRT unit ci cuit diag am 40

(4) Main PCB ci cuit diag am

(5) MODEM PCB ci cuit diag am

(6) Gene al wi ing diag am

(7) Mechanism assembly d awing

11. Attached book

CWR-685E Ope ating Inst uctions

1. Introd ction

(Concept and cautions of t oubleshooting)

1) When epai ing a t ouble in a compute system, it is essential, in the fi st place, to distinguish

whethe the t ouble is due to softwa e o ha dwa e. When it is found to be a ha dwa e t ouble,

it is then equi ed to judge whethe it is due to inside of the inte face device – such as, in this

system, PCI (IC28), PIA (IC32), CRTC (IC18), output latch (IC27), signal input po ts (IC45,

IC46, IC40) – o due to outside of the inte face device.

2) Actions of PCI, PIA, CRTC equi e setting by the softwa e, and they do not ope ate unless set-

ting is made no mally. In a t ouble of compute block, display is not made since CRTC does not

ope ate, data eading f om keyboa d and data output to p inte a e not done because PIA does

not ope ate, and even cont ol of t ansmission and eception by SEND-AUTO-RECEIVE switch is

impossible because PCI, output latch, and signal input po ts do not ope ate no mally.

3) One of possible t oubles in the compute block is a defect of the ROMs (IC29, IC30) in which

softwa e is w itten. The efo e, when the Compute does not seem to ope ate no mally, eplace

the IC29 and IC30 in the fi st place. (The both ICs a e mounted by way of socket. Always e-

place the two ICs at the same time. If specified tool cannot be used when dismounting, emo-

ve with pa ticula ca e not to bend the lead pins of ICs.)

4) In the desc iption, "H level at TTL level" o me ely "H level" efe s to DC + 2.4 V to +5 V; "L le-

vel at TTL level" o me ely "L level" means DC +0.8 V to 0 V.

5) It must be noted, that no mal output signal may not be delive ed f om the IC also due to t ou-

ble at the load side.

6) Since the wavefo m at check point of f equency is often othe than 50 % in duty atio (such as

TP-3 on main PCB), it is bette to use an oscilloscope of t igge ed sweep system, athe than

f equency counte (Howeve , oscilloscope of synch onized sweep o f ee- unning sweep system

is not p ope .)

7) In this system, many connecto s a e used in the connections of the PCBs, switches and othe

modules in o de to facilitate assembly, maintenance, checking and eplacement. Acco dingly,

t oubles in these connecto s a e also p obable, such as faulty contact and defective connection

between contact pin and vinyl coated wi e within connecto plug housing (in the case of solde -

less connection).

Besides, p obable causes of compute t oubles may also include faulty contacts of the socket in

softwa e ROM (IC29, IC30), and take this point also into conside ation when epai ing.

8) The IC numbe s, pa t numbe s, and connecto numbe s efe to the numbe s on the main PCB

(PCB No. 810529-1) unless othe wise noted.

2. General description

2.1 Composition

The block diag am of this System is shown in attached d awing. The p og am ROM contains a total

of 6 k bytes, consisting of 2732 × 1 and 2716 × 1; the RAM has 128 bytes built in the MPU and

2 k bytes of 2114 × 4; the video RAM ope ates on 2114.

The MPU (mic o p ocessing unit) is equivalent to Moto ola MC6802 (the machine code is same as

MC6800), and clocks at 3.3792 MHz divided to 1/4 f om 13.5168 MHz a e fed f om the EXTAL te -

minal. Since the clocks a e fu the divided to 1/4 in the MPU, the system finally ope ates on clocks

at 844.8 kHz. This clock at 844.8 kHz is delive ed as E signal f om pin 37 of MPU, and is given to a

pe iphe al device of this system as a synch onizing signal.

Equally impo tant as E signal a e VMA and R/W.

The VMA becomes TTL level H only when add ess data delive ed f om the MPU is valid; the R/W

becomes TTL level H when the MPU eceives data f om pe iphe al device and tu ns to TTL level L

when data is given f om the MPU to pe iphe al device.

These data exchanges a e synch onized with the change of E signal f om TTL level H to TTL level L

when the VMA is at TTL level H.

Since the MC6802 is an eight-bit MPU (CPU), it can exchange data with pe iphe al device by way

of input/output te minals D0 to D7 of 8-bit bidi ectional data.

Fo selection of add ess, the e is an add ess data output te minal of 16 bits, but since the A15 of

highe position is not used in this system, the total add ess space is 32 kbytes.

Fo conve sion f om pa allel to se ial of sending data of RTTY and conve sion f om se ial to pa allel

of eceived data, a USART (unive sal synch onous/asynch onous eceive /t ansmitte ) equivalent

to Intel 8251A is used, so that the t ansmission and eception may be ope ated simultaneously.

Fo data eading f om the keyboa d and data output to the p inte , a PIA (pe iphe al inte face

adapte ) equivalent to Moto ola MC6821 is used, and the data input and output a e effected in the

pa allel system of ASCII codes.

The sc een display is cont olled by the Hitachi HD46505S CRTC (CRT Cont olle ) equivalent to Mo-

to ola MC6845S. The CRTC can set the display fo mat f eely acco ding to the command f om the

CPU. In this system, a fo mat of 32 cha acte s/line by 20 lines is dete mined.

Since the CRTC, PIA, and USART do not ope ate unless the action is set immediately afte the

powe sou ce is tu ned on o eset, the p esc ibed data is w itten in the fi st place in this System.

In the event of t ouble in the MPU block, since this setting is not effected, nothing appea s on the

display sc een if the main powe switch is tu ned on.

The method to judge whethe the t ouble is due to the MPU block o due to one of the devices o

input/output units connected to the device is mentioned late .

2.2 Flow of signal

A block diag am is shown in attached sheet. Refe ing to the block diag am, the flow of signal is

explained below.

An audio signal fed f om the AF IN (RX o TAPE) te minal of the ea panel when eceiving is selec-

ted by the RX/TAPE input selecto on the f ont panel, and is delive ed to AF OUT te minal in the

ea panel, and is, at the same time, fed into AF input (J3-1) on MODEM PCB and AF input (J9-1)

on main PCB. The efo e, the AF OUT can be also used as AF input te minal (at this time, howeve ,

the AF IN RX and AF IN TAPE must be used as output te minals).

The CW audio signal fed into the main PCB is given to the J9-3 fo d iving the AGC amplifie fo

CW and input monito Speake , and, afte being cont olled in the volume by the input slide VR con-

nected between J9-3 and J9-5, d ives the Speake fo input sound monito connected between J9-

13 and J9-14 o the EXT SP output te minal.

The CW audio signal given to the AGC amplifie (IC42) passes th ough the active band pass filte

(IC42) at cente f equency of 800 Hz, and is conve ted into a digital signal by the PLL System de-

code (IC44) fo CW to cont ol the gate of monito oscillation sound at 800 Hz fo CW, and is si-

multaneously ead f om the CW signal input po t (pin 2 of IC45) in the Compute block, the eby

flicke ing the LED fo CW monito at the same time.

When the CW/RTTY selecto on the f ont panel is set at RTTY side, the CW/RTTY selection signal

input (J7-11) on the main PCB is at L level, and is ead f om the input po t (pin 12 of IC40) in the

Compute block, and the gate (pin 1 of IC12) becomes L level at the same time. As a esult, the

output of PLL decode becomes invalid.

When a key on the keyboa d which is connected to the teleg aph te minal on the ea panel is

p essed, the key ope ation signal is given to a key signal input (J3-2), and is ead f om the key sig-

nal input po t (pin 4 of IC45) to light up the LED fo CW monito , the eby opening the output gate

of CW monito OSC. At the same time, t ansisto switches TR5, TR8 fo keying-out (SW OUT CW)

a e tu ned on.

At this time, the compute , in o de to tu n on the t ansisto switch TR9 fo t ansmission and e-

ception cont ol of the t ansmitte , sets the output po t (pin 6 of IC27) to TTL level H, and sets the

eset delay time , so that the signal may be set to the initial value again wheneve key ope ations

a e subsequently made. When the time expi es, the TR9 is cut off. Meanwhile, this time is not

desc ibed in the ci cuit diag am because it is a softwa e time by the compute .

The CW signal ead f om the CW signal input po t is decoded, and is delive ed to the display

sc een and p inte .

The RTTY audio signal fed f om J3-1 on MODEM PCB is conve ted into a digital signal (fo details

of conve sion see the desc iption of pe fo mance of MODEM block), and is delive ed f om J4-7,

and is supplied to the INT side of the FSK DEMOD INT/EXT slide switch in the ea panel. At the

EXT side, a signal f om the FSK TTL IN side is supplied. The digital signal selected by this slide

switch is fed again into the J4-8 of MODEM PCB.

The logic ci cuit composed of IC10, IC12 on the MODEM PCB selects eithe eceived demodulated

signal (TU/EXT) o sending signal (FSK) depending on the cont ol signal STB o RX/TAPE given

f om the main PCB, and delive s the selected signal to the FSK OUT (J6-3). The signal delive ed

f om the FSK OUT (J6-3) is fed into the FSK IN (J10-2) in the main PCB, and is given to RXD (pin

3) of RTTY eceived signal input po t (IC28, USART), and is conve ted f om se ial to pa allel in the

IC28 being synch onized with the baud ate of 1/16 of the clock applied to RXC (pin 25) of IC28.

The pa allel data thus conve ted is decoded, and is delive ed to the display sc een and p inte .

2.3 Control of SW OUT REMOTE

The SW OUT REMOTE te minal of the ea panel is connected to the REMOTE (J3-4) te minal of

main PCB.

This te minal is di ectly sho ted by the contact of the SEND-AUTO-RECEIVE switch when this

switch is set to SEND side. When AUTO o RECEIVE position is selected, this te minal is cont olled

by the TR9 on the main PCB.

This te minal and the SEND-AUTO-RECEIVE switch is so wi ed that the J8-5 on the main PCB may

be connected to GND when the switch is set to SEND position, and that the J8-8 is simila ly con-

nected to GND when it is set to RECEIVE side. Thus, this te minal always monito s the state of this

switch, and cont ols the t ansmission and eception and TR9.

2.4 Flow of signal in transmission

When a key is dep essed, an ASCII code of 8-bit pa allel positive logic is delive ed f om the key-

boa d, and is given f om pin 4 to pin 11 of J6 on the main PCB. In succession, a data st obe signal

of negative logic is applied to pin 13 of J6, and is conve ted to a pulse signal by the one-shot mul-

tivib ato in IC6 to be fed in pin 40 of IC32.

At this time, acco ding to the initially set fo mat, the IC32 set the IRQB (pin 37) to L level in o de

to ask the MPU to ead data. In consequence, the MPU, immediately o afte finishing the p ocess

being un at that time, eads the data f om the keyboa d being applied to PA0 to PA7 in IC32, and

etu ns the IRQB to H level at the same time, and delive s a data eading acknowledgement signal

to the CA2 (pin 39) as negative logic pulse signal of 1.183 µs. The ACK signal is not used when

feeding f om the keyboa d, but is used when cont olling the system by means of othe mic ocom-

pute o the like instead of the keyboa d. In such a case, the pa allel data should not be conve ted

until the esponse of ACK signal is confi med.

When the MPU eads the data, a p ocess suited to the state, such as command p ocessing, w iting

into t ansmission buffe a ea, w iting into memo y a ea, is effected acco ding to the data.

REFERENCE

o In t ansmission of CW, the data in the t ansmission buffe is conve ted to CW code, and the

output of CW output po t (pin 2 of IC27) is cont olled being synch onized with the clock

signal c eated in IC35 and ead in f om pin 2 of IC40. This clock f equency may be va ied

by means of SPEED slide VR in the f ont panel.

When the CW output po t becomes H level at TTL level, the TR5 and TR8 a e tu ned on, so

that a key ope ation signal can be obtained f om the SW OUT CW output te minal in the e-

a panel connected to J3-6. In CW ID mode at the time of RTTY, the TR10 is tu ned off by

the signal of CW ID output po t (pin 9 of IC27) which is ope ating simultaneously with CW

output po t, and the signal is shifted to a blank space.

o In t ansmission of RTTY, when the MPU w ites data into USART, they a e conve ted to se ial

signals in synch onism with the baud ate at 1/16 of the clock given to pin 9 of USART

(IC28), and a e delive ed f om TXD (pin 19) of USART, the eby cont olling the TTL-OUT

(J10-3 te minal) and TR10 as in the case of CW ID. The TTL-OUT (J10-3 te minal) of main

PCB is connected to the FSK (J6-2 te minal) on MODEM PCB, and is delive ed at TTL level

to the FSK TTL OUT te minal in the ea panel f om the FSK TTL (J4-9 te minal). The FSK

signal is, at the same time, applied also to pin 5 of IC4 as AFSK shift signal. The AFSK sig-

nal c eated he e is delive ed f om J4-3 te minal on MODEM PCS, and is sent to the AFSK

GAIN VR in the ea panel, and is synthesized with the signal of CW monito OSC at 800 Hz

which is delive ed f om J3-7 on main PCB (in actual ope ation, eithe one signal only is gi-

ven he e). Afte level adjustment at AFSK GAIN VR, the signal is fed again to J4-1 te minal

on MODEM PCB, and eappea s at J4-4 te minal as AFSK signal having shaped wavefo m,

and is delive ed f om the AFSK OUT te minal in the ea panel.

The AFSK monito speake d ive output which is delive ed f om J3-8 te minal on MODEM

PCB is once fed to J10-10 on the main PCB, and is synthesized with the CW monito spea-

ke d ive output, and then delive ed to J9-6 te minal. This output signal is applied to the

VOLUME slide VR in the f ont panel to be cont olled in the sound volume, and d ives the

built-in output monito speake o PHONE output te minal in the ea panel.

3. Inp t/o tp t actions

3.1 Actions of switches

RESET PB

Only while it is being dep essed, the J7-2 te minal on main PCB is connected to GND.

FILTER

In OFF position, the J7-3 te minal on main PCB is connected to GND.

In ON position, the J7-4 te minal on main PCB is connected to GND.

SPACE NARROW

In NARROW position, the J7-5 te minal on main PCB is connected to GND.

CWIDA/CWIDB

In CWID A position, the J706 te minal on main PCB is connected to GND; in CWID B, the

ci cuit is open.

PAGE PB

While it is being dep essed, the J7-8 te minal on main PCB is connected to GND; when it is

not pushed, the J7-7 te minal on main PCB is connected to GND.

MODE A/MODE B

In MODE B, the J7-9 te minal on main PCB is connected to GND.

CW/RTTY

In RTTY position, the J7-11 te minal on main PCB is connected to GND; in CW position, the

J1-7 te minal on MODEM PCB is connected to GND.

ASCII/BAUDOT

In ASCII position, the J7-12 on main PCB is connected to GND.

LTR PB

Only while it is being p essed down, the J7-14 on main PCB is connected to GND.

FIG PB

Only while it is being p essed down, the J7-13 on main PCB is connected to GND.

LOCK U.O.S.

When tu ned on, the J7-15 te minal on main PCB is connected to GND.

NOR/REV

In REV position, J1-2 te minal on MODEM PCB is connected to GND.

BAUD 6-position switch

One of the te minals J2-2 to J2-7 on MODEM PCB is connected to GND.

SHIFT 3-position switch

When 425 is tu ned on, the J1-12 te minal on MODEM PCB is connected to GND.

When 850 is tu ned on, the J1-11 te minal on MODEM PCB is connected to GND.

TONE LOW

When tu ned on, the J1-10 te minal on MODEM PCB is connected to GND.

RX/TAPE

In RX position, the AF IN RX te minal and AF OUT te minal in ea panel and J9-1 te minal

on main PCB a e connected togethe .

In TAPE position, the AF IN TAPE te minal and AF OUT te minal in ea panel and J9-1 te -

minal on main PCB a e connected togethe , and the J7-16 te minal on main PCB is connec-

ted to GND.

SEND/AUTO/RECEIVE

In SEND position, the SW OUT PHONE te minal in ea panel is connected to GND, and the

J8-5 te minal on main PCB is connected also to GND.

In RECEIVE position, the J8-8 te minal on main PCB is connected to GND.

3.2 Actions of external control signal o tp t ports

This pa ag aph desc ibes the pe fo mance of output po ts on the main PCB in which outputs va y

depending on the setting of each switch o commands. These outputs a e cont olled by the com-

pute .

J10-5

When RX/TAPE selecto is set to RX side, the level becomes H. When the RESET button is

being pushed down, the level is L.

That is, when the RESET button is p essed, the level is L, and when the button is eleased,

the level tempo a ily becomes H, but soon etu ns to L.

This output cont ols the J1-1 te minal on MODEM PCB.

Output po t

The IC27 is an 8-bit latch IC. The exte nal cont ol signals of this system a e mainly delive -

ed f om this IC. While the RESET button is kept dep essed, this output emains at L level.

Pin 15

An output is delive ed to J10-4 te minal. The output becomes H level when sending RTTY.

This output cont ols the J6-1 te minal on MODEM PCB, and opens the AFSK output gate of

RTTY when the level is H to delive y an AFSK oscillation signal.

Pin 16

A t ansmission/ eception changeove signal fo softwa e cont ol is delive ed. When the le-

vel is H, the SW OUT REMOTE is tu ned on, and the eading gate of CW audio demodula-

ted signal is also closed.

Pin 5

Du ing t ansmission of CWID, the level becomes H in synch onism with CW code. When the

level is H, the SW OUT FSK is tu ned on, and the FSK TTL OUT is set to L level. In CW mo-

de, this pin ope ates in synch onism with pin 2.

Pin 2

When sending CW, the level becomes H in synch onism with CW code. When the level be-

comes H, the SW OUT CW is tu ned on, and the CW LED is lit.

Pin 9

When the level becomes H, the gate of CW monito OSC is opened, and an 800 Hz monito

sound is delive ed to the AFSK OUT and inte nal monito Speake .

Pin 19

When the level is H, the Output of SW OUT FSK is maintained in the ma k. Howeve , since

this Output po t is not used in the p esent Softwa e, the level always emains at L.

Pin 16

This is designed as an output fo changing ove the ate of f equency division of IC4. This

function, howeve , is not used in the p esent Softwa e. Inte nally, this pin is used as key

ope ation mode memo y of teleg aph key of CW, the level becomes H when the teleg aph

key is pushed down.

Pin 12

Though it is designed as a means of cont ol of display sc een changeove by Softwa e, this

function is not used in the p esent Softwa e. The efo e, the level is always L.

3.3 Actions of CW a dio demod lator

The IC42 is a No ton amplifie having fou logic ci cuits of identical function contained in one pack-

age. In this system, two of the fou logic ci cuits a e used to compose an AGC amplifie fo CW

and band pass filte . The othe two logic ci cuits a e not used.

The ci cuit of the AGC amplifie block is identical with that of AGC amplifie fo RTTY on the MO-

DEM PCB, whe eas the ci cuit fo CW uses 10 µF C14 in o de to inc ease the time constant.

This AGC amplifie is actually esponsible fo both AGC action and limite action.

The output of the AGC amplifie is fed to the band pass filte on the next stage by way of coupling

capacito C37.

The esisto R28 is fo adjusting the input level to the band pass filte . The wavefo m at test point

TP-5 of the band pass filte output attains the maximum amplitude when the output amplitude

f om the AGC amplifie becomes 90 % of the maximum value as an 800 Hz signal is fed f om the

AF IN, and the peak of the wavefo m is slightly defo med at 100 % input, in no mal state. This e-

sisto is va ied in the ange of 220 to 330 kohms in each manufactu ing lot.

If the esistance is too small, a misdecoding may be caused by noise signal whe e the e is no sig-

nal.

The va iable esisto VR5 is fo setting the cente f equency of band pass filte . It is adjusted to

800 Hz at the time of manufactu e.

Table des matières

Autres manuels TELEREADER Convertisseur de média

TELEREADER

TELEREADER CWR-610E Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur