Teledyne 3000MA Manuel utilisateur

Addendum for Model 3000MA Percent Oxygen Analyzer

Page 1

Teledyne Analytical Systems

Q002870 C.O. 85723

The instruction manual included with your analysis system from

Teledyne Analytical Instruments describes the standard features of

the system. Refer to the manual for information regarding all

standard features of the model that you have selected.

In addition, your specific system has been designed according to the

needs that you specified at the time of purchase. The information

contained in this addendum addresses those needs and supersedes

any conflicting instructions and descriptions in the standard

instruction manual.

NOTE: All drawings that relate to your system are at the rear of

this manual.

System Overview

The Model 3000MA Percent Oxygen Analyzer is configured with a

Paramagnetic sensor and auto cal valves. This instrument has a

general purpose area class.

Power Requirements

This instrument operates from a power source of 220 VAC at 50/60

Hz.

Analysis Range

The Model 3000MA has three user defined analysis ranges of 0-5 to

0-100 Percent Oxygen (O2).

Signal Outputs

This Model 3000MA has a signal output of 4-20mA isolated.

Additional Operating

instructions and/or

information for your

Model 3000MA

Percent Oxygen

Analyzer

Addendum for Model 3000MA Percent Oxygen Analyzer

Page 2

Teledyne Analytical Systems

Software

The software for this instrument adds hold timers for span and zero

calibration; each calibration has its own timer separate timer.

Span Delay:

By pressing the Span key, the operator accesses the setup mode of

the span calibration. After selecting AUTO span calibration the

following screen will be the hold timer adjustment:

Span Delay: 5 min.

<ENT> For Next

The hold time for the span can be adjusted between 1 minute and 60

minutes. Five minutes is the factory default. When changed the value

is stored so it can be recovered after power down.

Zero Delay:

By pressing the Zero key, the operator accesses the setup mode of

the zero calibration. After selecting AUTO zero calibration the

following screen will be the hold timer adjustment:

Zero Delay: 5 min.

<ENT> For Next

The hold time for the span can be adjusted between 1 minute and 60

minutes. Five minutes is the factory default. When changed the value

is stored so it can be recovered after power down.

Reference Drawings

D74505 Outline Diagram

B74504 Piping Diagram

Spare Parts

A78648 EPROM Software Assembly

Project Engineer ________________ Date ______________

Autres manuels pour 3000MA

Table des matières

Autres manuels Teledyne Instrument analytique

Teledyne

Teledyne 328 Manuel utilisateur

Teledyne

Teledyne 2020 Manuel utilisateur

Teledyne

Teledyne 3020T Manuel utilisateur

Teledyne

Teledyne 3010PA Manuel utilisateur

Teledyne

Teledyne 6000A Manuel utilisateur

Teledyne

Teledyne 2750 Manuel utilisateur

Teledyne

Teledyne 3000PA Manuel utilisateur

Teledyne

Teledyne 3010TB Manuel utilisateur

Teledyne

Teledyne 6200A Manuel utilisateur

Teledyne

Teledyne TURBO2 Manuel utilisateur

Teledyne

Teledyne 3060E Manuel utilisateur

Teledyne

Teledyne 3000MA Manuel utilisateur

Teledyne

Teledyne 3010MA Manuel utilisateur

Teledyne

Teledyne AX300-I Manuel utilisateur

Teledyne

Teledyne T3AWG3K Series Manuel utilisateur

Teledyne

Teledyne 311XL Series Manuel utilisateur

Teledyne

Teledyne TED 200-T Manuel utilisateur

Teledyne

Teledyne 4020 Manuel d'installation et d'exploitation

Teledyne

Teledyne 4040 Manuel de la liste des pièces

Teledyne

Teledyne 3000TB Manuel utilisateur

Teledyne

Teledyne 317 Series Manuel utilisateur

Teledyne

Teledyne 3010TA Manuel utilisateur

Teledyne

Teledyne 3000TA-XL-EU Manuel utilisateur

Teledyne

Teledyne 7500 Series Manuel utilisateur

Manuels Instrument analytique populaires d'autres marques

Cocraft

Cocraft NLT04 Manuel utilisateur

M&C

M&C GENTWO PMA1000 Manuel utilisateur

MICRO-EPSILON

MICRO-EPSILON optoncdt 1700 Manuel utilisateur

CONDTROL

CONDTROL XP4 PRO Manuel utilisateur

Extech Instruments

Extech Instruments BR200 Manuel utilisateur

Dewetron

Dewetron DEWE-30-16 Manuel du produit

EXTOL PREMIUM

EXTOL PREMIUM 8820043 Instructions d'installation et d'utilisation

RIDGID

RIDGID SeeSnake Compact Manuel utilisateur

YDLIDAR

YDLIDAR TIA Manuel utilisateur

Olympus

Olympus IPLEX FX Series Manuel utilisateur

Bosch

Bosch GLM 50 C Professional Manuel utilisateur

Reflecta

Reflecta DigiEndoscope Manuel utilisateur

Chinavision

Chinavision CVACZ-G696 Instructions de montage

Fuji Electric

Fuji Electric ZKMA Manuel utilisateur

VOLTCRAFT

VOLTCRAFT IC-100HD Manuel utilisateur

RIDGID

RIDGID micro CA-25 Manuel utilisateur

Würth

Würth MASTERVISION MINI REC Manuel utilisateur

AMI

AMI 2001LC Manuel utilisateur