Teledelta MPR Series Manuel utilisateur
MPR Receiver Quick Start Guide vr1.5
MPR Receiver –Overview
TeleDelta is proudly an Australian owned company. s:\teledelta\mpr series\mpr receiver quick start guide vr1.5.docx
www.teledelta.com Page 1 of 17
Quick Start
Operation and Installation Guide
MPR Series
Multi-Purpose Receiver
MPR Receiver Quick Start Guide vr1.5
MPR Receiver –Overview
TeleDelta is proudly an Australian owned company. s:\teledelta\mpr series\mpr receiver quick start guide vr1.5.docx
www.teledelta.com Page 2 of 17
Contents
Revision ..................................................................................................................................................2
Quick Start - Getting Started Guide ........................................................................................................3
Navigation Keys Operation Instruction................................................................................................4
Confirm or Change the Default IP Address.........................................................................................4
Configuration through WEB Management..............................................................................................5
First Time Log On................................................................................................................................5
Main Interface Introduction..................................................................................................................6
Appendix 1 - Setup Example Audio Only Service (TSIMA)....................................................................7
Setting the Receiver RF...................................................................................................................7
Status page......................................................................................................................................8
Check the CA / CAM settings ..........................................................................................................9
Select Program Decryption............................................................................................................10
Select Program ..............................................................................................................................11
Appendix 2 - Setup Example VAST TV service (ABC24).....................................................................12
Setting the Receiver RF (single tuner models)..............................................................................12
Status page....................................................................................................................................13
Check the CA / CAM settings ........................................................................................................14
Select Program Decryption,...........................................................................................................15
Select Program ..............................................................................................................................16
Revision
File
MPR Receiver Quick Start Guide Vr1.5.Docx
MPR Receiver Quick Start Guide vr1.5
MPR Receiver –Overview
mpr receiver quick start guide vr1.5.docx Page 3 of 17
Quick Start - Getting Started Guide
Switch on the equipment through the back power switch, the unit is powered up and start the
initialization.
After power on the LCD screen is lights up, and displays information as follows
The initialization takes about 30 seconds to complete. The input/output indicator LEDs turn red after
the first successful initialization because the signal is not locked. After configuration of the device, the
corresponding LEDs will show the correct status.
MPR Receiver Quick Start Guide vr1.5
MPR Receiver –Overview
mpr receiver quick start guide vr1.5.docx Page 4 of 17
Navigation Keys Operation Instruction
Use the 6 navigation keys on front panel: Up / Down / Left / Right / Menu / Ok to enter the
configuration menu.
Enter “Menu”:
Press “OK” button to enter main menu.
Exit Menu/Back for parent Menu
Upon completion of configuration settings, press “OK” button until you go back
to the Parent Menu.
Enter Sub-Menu
Press OK button to enter main menu.
Select a sub-menu by pressing UP and DOWN button.
Press MENU button on the selected sub-menu.
To change a parameter
Step 1: Enter main menu by pressing OK button.
Step 2: Scroll sub-menu by pressing UP and DOWN button, and press MENU button to
change the selected sub-menu.
Step 3: To change parameter settings, press RIGHT and LEFT button to move the cursor in
which change must be made.
Press UP button and DOWN to input / select an appropriate setting, then press MENU button
to save.
Confirm or Change the Default IP Address
Note DHCP is not provided (despite the menu selection)
1. check out the IP on the LCD screen.
2. use the button on the front panel to change the IP, gateway and subnet mask The gateway
should be the same as the management PC’s. The subnet mask should be the same as the
management PC’s s. The IP and the server’s IP should be in the same subnet section.
3. reboot the device to take effect.
4. ping the new IP to check whether the device can connect to the management PC.
MPR Receiver Quick Start Guide vr1.5
MPR Receiver –Overview
mpr receiver quick start guide vr1.5.docx Page 5 of 17
Configuration through WEB Management
First Time Log On
Configuration is best performed via a web browser.
Start a browser and browse to the set ip address of the unit. The log on page will appear
The default User Name and Password are “admin”.
If you are unable to connect check for possible reasons for unsuccessful log on:
IP address/ network mask/gateway don’t match with the management PC’s
User name/password is wrong –check the caps lock - lower case is required.
The device is connected to the wrong interface
MPR Receiver Quick Start Guide vr1.5
MPR Receiver –Overview
mpr receiver quick start guide vr1.5.docx Page 6 of 17
Main Interface Introduction
After successful log on, the following screen will display:
The main interface can be divided into two areas.
1. Menu: each screen shares same 6 tabs including “Status”, “Inputs”, “Outputs”, “CA”, “System”
and “Reset”.
2. Settings: Configuration data for each function
Menu
1
Settings
2
MPR Receiver Quick Start Guide vr1.5
Appendix 1: Setup Example –Audio Only Service - TSIMA
mpr receiver quick start guide vr1.5.docx Page 7 of 17
Appendix 1 - Setup Example Audio Only Service (TSIMA)
Let’s assume that you have a dish and LNB connected and pointed correctly and you are going after
the Optus VAST TSIMA service
Setting the Receiver RF
“Zoomed In” version for TSIMA as At Oct 2013
Note: Adjust your LNB L.O. Frequency to suit (if required)
Select
Optus C1/D3
156E, use
13V for
standard
Vertical
MPR Receiver Quick Start Guide vr1.5
Appendix 1: Setup Example –Audio Only Service - TSIMA
mpr receiver quick start guide vr1.5.docx Page 8 of 17
Status page
If all these settings are correct the receiver will lock and the Status page will look similar to this:
- Check for a lock
If you have a green lock as shown here and on the front panel then continue the setup
Note –Green
for locked
signal
MPR Receiver Quick Start Guide vr1.5
Appendix 1: Setup Example –Audio Only Service - TSIMA
mpr receiver quick start guide vr1.5.docx Page 9 of 17
Check the CA / CAM settings
They should suit the speed of the CAM card you are using:
Now check the
CA settings
MPR Receiver Quick Start Guide vr1.5
Appendix 1: Setup Example –Audio Only Service - TSIMA
mpr receiver quick start guide vr1.5.docx Page 10 of 17
Select Program Decryption
All the programs are shown and from here you can route them to the CA/CI/CAM slot for the channels
that you want to de-scramble
Note: - Only have one service routed to the CI Slot if you have a single service card
Now check / set
the CA settings
Select
Table des matières
