Telcoma Automations FM420U Manuel d'installation

FM420U

ISTFM420U

V.06.2013

MULTI-CHANNEL 433.92 MHz RADIO CONTROL.

Operation and programming instructions.

Fig. 1

Fig. 2

CR2430

14.2

116.0

40.8

dimensions in mm

DISPLAY

SPECIFICATIONS

Multi-channel radio control for quick and intuitive control of 20 users with

receivers in the series FM400U

Innovative and stylish container with white led display which, located

under semi-transparent plastic, shows the selected channel. At the centre

of a rubber faced keypad with three function keys and two up-down

channel selection keys. Fitted with practical non-slip rubber buttons.

TECHNICAL SPECIFICATIONS u.m. FM420

Power supply with battery type Vdc 3 (CR2430)

Transmission consumption mA 50

Frequency MHz 433,92

Modulation FSK

Operating temperature °C -20 +55

Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate this equipment.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE.

Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

Fig. 1

Fig. 2

CR2430

14.2

116.0

40.8

dimensions in mm

DISPLAY

SPECIFICATIONS

Multi-channel radio control for quick and intuitive control of 20 users with

receivers in the series FM400U

Innovative and stylish container with white led display which, located

under semi-transparent plastic, shows the selected channel. At the centre

of a rubber faced keypad with three function keys and two up-down

channel selection keys. Fitted with practical non-slip rubber buttons.

TECHNICAL SPECIFICATIONS u.m. FM420

Power supply with battery type Vdc 3 (CR2430)

Transmission consumption mA 50

Frequency MHz 433,92

Modulation FSK

Operating temperature °C -20 +55

Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate this equipment.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE.

Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

Use key 1 or 3 (indicated in the drawing) to scroll through to the

flashing

Use the central key to confirm

The channel will start flashing.

Use key 3 (indicated in the drawing) or 1 to scroll through the

channels to

Press key 2 to add the channel 02 to C2. The dot next to 2 will light

up ( ).

To remove it from C2 press key 4, and the dot next to 2 will turn off

( ).

If a dot is lit next to 0 ( ), this means that channel 02 also

belongs to group C1.

Use key 3 (indicated in the drawing) or 1 to scroll through the

channels to

Press key 2 to add the channel 15 to C2. The dot next to 5 will light

up ( ).

To remove it from C2 press key 4, and the dot next to 5 will turn off.

DESCRIPTION OF COMPONENTS

Fig. 1

1 channel decrease key

2. CH1 transmission key

3. channel increase key

4. CH2 transmission key

5. CH3 transmission key

MAIN FUNCTIONS

Fig. 2

Battery panel opening and

external dimensions in mm

This transmitter can control up to 20 automations, each of which can be

sent 3 different functions (for example OPEN, CLOSE and STOP).

To scroll through the 20 channels, press key 1 (to decrease the number) or

3 (to increase the number).

After selecting the channel, press keys 2, 4 or 5 to transmit the code.

To memorise the code in the user, read the receiver instructions.

Press and hold the the keys indicated in the drawing (1 and 3)

until starts to flash.

-Channels groups (C1, C2).

Use this menu to group channels as required. Once configured, press a

command for C1 or C2 to transmit all selected channels in sequence.

Example: how to group channels 02 and 15 in C2

SPECIAL FUNCTIONS

Use key 1 or 3 (indicated in the drawing) to scroll through to the

flashing

Use the central key to confirm

The channel will start flashing.

Use key 3 (indicated in the drawing) or 1 to scroll through the

channels to

Press key 2 to add the channel 02 to C2. The dot next to 2 will light

up ( ).

To remove it from C2 press key 4, and the dot next to 2 will turn off

( ).

If a dot is lit next to 0 ( ), this means that channel 02 also

belongs to group C1.

Use key 3 (indicated in the drawing) or 1 to scroll through the

channels to

Press key 2 to add the channel 15 to C2. The dot next to 5 will light

up ( ).

To remove it from C2 press key 4, and the dot next to 5 will turn off.

DESCRIPTION OF COMPONENTS

Fig. 1

1 channel decrease key

2. CH1 transmission key

3. channel increase key

4. CH2 transmission key

5. CH3 transmission key

MAIN FUNCTIONS

Fig. 2

Battery panel opening and

external dimensions in mm

This transmitter can control up to 20 automations, each of which can be

sent 3 different functions (for example OPEN, CLOSE and STOP).

To scroll through the 20 channels, press key 1 (to decrease the number) or

3 (to increase the number).

After selecting the channel, press keys 2, 4 or 5 to transmit the code.

To memorise the code in the user, read the receiver instructions.

Press and hold the the keys indicated in the drawing (1 and 3)

until starts to flash.

-Channels groups (C1, C2).

Use this menu to group channels as required. Once configured, press a

command for C1 or C2 to transmit all selected channels in sequence.

Example: how to group channels 02 and 15 in C2

SPECIAL FUNCTIONS

Press key 5 to confirm. The text appears briefly and the

radio control returns to normal operating status.

- Maximum number of channelsDisplay of channels can be set to the

minimum indispensable, to optimise search times.

Procedure:

To increase battery lifetime, set a short delay interval.

Groups C1 and C2 are only displayed if programmed.

From the secondary menu, press key 5 to select

Use key 3 (indicated in the drawing) or 1 to scroll through values

00 to 20.

Example: on selection of 12, all channels from 00 to 15 will be

displayed.

Press key 5 to confirm. The text appears briefly and the radio

control returns to normal operating status.

Use key 2 (indicated in the drawing) or 4 to scroll through values

to corresponding to a display shutdown delay from

approx. 2 to 10 seconds.

Use the central key to complete programming of C2. The text

is displayed briefly, followed by after which the display

turns off.

Access to secondary menu

This menu contains the following functions:

- Display shutdown delay setting

- Maximum channel number setting

- Channel 00 repetition function

- Firmware Version

Procedure to enable secondary menu:

Press and hold the keys indicated in the drawing for approx. 10

seconds until appears.

key 3 (indicated in the drawing) or 1 to scroll through the menu

until the required function is displayed

- Display shutdown delay

The channel remains on display after release one of the keys for a time

interval that can be modified as follows:

From the secondary menu, press key 5 to select

Press key 5 to confirm. The text appears briefly and the

radio control returns to normal operating status.

- Maximum number of channelsDisplay of channels can be set to the

minimum indispensable, to optimise search times.

Procedure:

To increase battery lifetime, set a short delay interval.

Groups C1 and C2 are only displayed if programmed.

From the secondary menu, press key 5 to select

Use key 3 (indicated in the drawing) or 1 to scroll through values

00 to 20.

Example: on selection of 12, all channels from 00 to 15 will be

displayed.

Press key 5 to confirm. The text appears briefly and the radio

control returns to normal operating status.

Use key 2 (indicated in the drawing) or 4 to scroll through values

to corresponding to a display shutdown delay from

approx. 2 to 10 seconds.

Use the central key to complete programming of C2. The text

is displayed briefly, followed by after which the display

turns off.

Access to secondary menu

This menu contains the following functions:

- Display shutdown delay setting

- Maximum channel number setting

- Channel 00 repetition function

- Firmware Version

Procedure to enable secondary menu:

Press and hold the keys indicated in the drawing for approx. 10

seconds until appears.

key 3 (indicated in the drawing) or 1 to scroll through the menu

until the required function is displayed

- Display shutdown delay

The channel remains on display after release one of the keys for a time

interval that can be modified as follows:

From the secondary menu, press key 5 to select

- Channel 00 repetition This new multi-channel control enables

programming of channel 00 so that it repeats transmission sequentially for

a set time interval.

This function is useful when channel 00 is optimised for centralised

commands, and repetition optimises reception of the radio signal.

Press key 5 to select

Press key 5 to confirm. The text appears briefly and the radio

control returns to normal operating status.

In this case (30) channel 00, after pressing a transmission key, is

transmitted at regular intervals for 30 seconds. On each

transmission, the text is displayed, followed by . Press

key 1 or 3 to interrupt transmission repetition.

To disable repeated transmission of channel 00, set in the

menu .

Use key 2 (indicated in the drawing) or 4 to scroll through values

00 to 40.

Select 00 to disable transmission repetition.

Select 10, 20, 30 or 40 to set the repetition interval in seconds.

- Firmware Version

Press key 5 to select . This displays a number corresponding

to the radio control firmware version.

BATTERY REPLACEMENT

To replace the battery, open the battery compartment and remove the

battery with the aid of a tool (for example the tip of a pen). Fit the new

battery taking care to observe polarity. See fig. 2 on page 2.

GUARANTEE

The present guarantee covers possible faults and/or irregularities due to

manufacturing defects and/or faults.

The guarantee will automatically decay in the event of tampering or mi-

suse of the product.

During the guarantee period TELCOMA srl pledge to repair and/or re-

place defective and non-tampered parts. The call charges, as well as

the collection, packaging and transportation costs of the product for re-

pair or replacement are at the clients full and exclusive expense.

- Channel 00 repetition This new multi-channel control enables

programming of channel 00 so that it repeats transmission sequentially for

a set time interval.

This function is useful when channel 00 is optimised for centralised

commands, and repetition optimises reception of the radio signal.

Press key 5 to select

Press key 5 to confirm. The text appears briefly and the radio

control returns to normal operating status.

In this case (30) channel 00, after pressing a transmission key, is

transmitted at regular intervals for 30 seconds. On each

transmission, the text is displayed, followed by . Press

key 1 or 3 to interrupt transmission repetition.

To disable repeated transmission of channel 00, set in the

menu .

Use key 2 (indicated in the drawing) or 4 to scroll through values

00 to 40.

Select 00 to disable transmission repetition.

Select 10, 20, 30 or 40 to set the repetition interval in seconds.

- Firmware Version

Press key 5 to select . This displays a number corresponding

to the radio control firmware version.

BATTERY REPLACEMENT

To replace the battery, open the battery compartment and remove the

battery with the aid of a tool (for example the tip of a pen). Fit the new

battery taking care to observe polarity. See fig. 2 on page 2.

GUARANTEE

The present guarantee covers possible faults and/or irregularities due to

manufacturing defects and/or faults.

The guarantee will automatically decay in the event of tampering or mi-

suse of the product.

During the guarantee period TELCOMA srl pledge to repair and/or re-

place defective and non-tampered parts. The call charges, as well as

the collection, packaging and transportation costs of the product for re-

pair or replacement are at the clients full and exclusive expense.

NOTE

Table des matières

Autres manuels Telcoma Automations Télécommande

Telcoma Automations

Telcoma Automations EDGE2 Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation