Tekvox TEK-MUHD44TP 79055 Manuel utilisateur

TEK-MUHD44TP 79055

4K 4x4 HDMI Matrix with HDBaseT Lite Outputs

User’s Manual

May 14, 2018

This manual only includes operational instructions and specifications,

and is not intended to be used for service. Specifications are subject to

change without notice. Please ask your local dealer for detailed

information.

may be transmitted or reproduced in any form or by any means without

Please check website or contact local supplier for updates.

www.tekvox.com

Operation Notice

In order to ensure the proper use of the product and the user’s safety, please

comply with the following items during installation and maintenance:

The system must be properly connected to earth ground. Do not use ungrounded

or two bladed plugs and ensure the alternating power supply ranged from 100v to

240v and from 50Hz to 60Hz.

Do not operate the device in locations above 100° F and below 30°F.

To avoid any damage by over heat, please provide adequate ventilation to

radiate the heat when operating the device.

The device should be turned off when in wet or humid areas.

The AC power supply line should be disconnected from main power during the

following operations:

Remove or reinstall any component on the device.

Disconnect or re-connect any connector on the device.

Please do not attempt to remove the cover on the device. There are no

serviceable components and high-voltage is present inside with risk of the

electric shock.

Do not splash any chemical product or liquid on or near the equipment.

Table of Contents

1. DESCRIPTION............................................................................................................1

2. FEATURES.................................................................................................................1

3. PACKAGE CONTENTS..............................................................................................1

4. FRONT AND REAR PANEL DESCRIPTION .............................................................2

4.1 FRONT PANEL OPERATION..........................................................................................................................................2

4.2 REAR PANEL OPERATION............................................................................................................................................3

4.4 HDBASETTWISTED PAIR CABLE CONNECTION ...............................................................................................................4

5. SYSTEM DIAGRAM ...................................................................................................5

6. SYSTEM OPERATION ...............................................................................................6

6.1 FRONT PANEL BUTTON CONTROL.................................................................................................................................6

FRONT PANEL BUTTON CONTROL ......................................................................................................................................6

Switching I/O connection.......................................................................................................................................6

EDID Management ................................................................................................................................................6

Inquiry....................................................................................................................................................................8

Clear operation ......................................................................................................................................................8

6.2 IR CONTROL ............................................................................................................................................................9

6.2.1 IR Remote Operation ....................................................................................................................................9

Usage of IR Remote ...............................................................................................................................................9

6.2.2 IR Operations ..............................................................................................................................................10

Force Carrier ........................................................................................................................................................10

Control Far-end Device locally .............................................................................................................................10

Control Local Device Remotely.............................................................................................................................11

RS232 CONTROL .........................................................................................................................................................12

Connection with RS232 Communication Port ......................................................................................................12

Control through 9-pin RS232 port........................................................................................................................12

Control through 3-pin RS232 port........................................................................................................................12

Installation/uninstallation of RS232 Control Software ........................................................................................13

6.3 RS-232 CONTROL ..................................................................................................................................................14

6.3.1 Commands ..................................................................................................................................................14

6.4 TCP/IP OPERATION -OPTIONAL ...............................................................................................................................18

6.5 IP CONFIGURATION.................................................................................................................................................18

6.6 CONNECTION AND CONTROL.....................................................................................................................................18

GUI for TCP/IP control..........................................................................................................................................19

GUI Update ..........................................................................................................................................................20

7. FIRMWARE UPDATING...........................................................................................21

8. TECHNICAL SPECIFICATION.................................................................................22

6 PANEL DRAWING.....................................................................................................23

9. TROUBLESHOOTING & MAINTENANCE...............................................................23

10. WARRANTY ...........................................................................................................23

TEK-MUHD44TP 4x4 HDBaseT Matrix

TEKVOX, INC. 1 www.tekvox.com

830.460.9099

1. Description

The TEK-MUHD44TP 79055 is a unique 4K 4x4 HDMI matrix switcher with HDBaseT outputs, RS232

and IR control of end-points, and EDID & HDCP management. Included in the unit are IR and RS-232

inserters for the HDBaseT connections, and audio de-embedders with both analog and digital

outputs. Any input can be routed to any output with support for high resolution 1080P and HD-3D.

Breakaway audio is not supported. The HDBaseT output supports PoC and works with TPHD412R to

transmit HDMI, IR and RS-232 over a single Cat6A cable up to 200 feet.

2. Features

HDMI resolution up to 4Kx2K

HDCP Compliant and DVI compatible, supporting DVI 1.0

Powerful EDID and HDCP management

HDBaseT Lite outputs, to transmit HDMI, IR & RS-232 up to 200’@ 1080 or 130’ at 4K over a

single Cat 6A cable

Output PoC provides power for all the receivers connected to the HDBaseT outputs

Front panel Menu operation for configuration, control and status

RS-232 control with simple ASCII commands

IR control

TCP/IP control

IR OUT signal switching follows with video signal, or can break away from video switching

Supports remote control from receiver by IR & RS-232

Supports centralized IR control to control all the remote display devices

Supports PCM, Dolby, and DTS 5.1 surround

Source detection to provide power control for DVDs and Blur-rays.

Standby mode operation to reduce energy and extend life.

3. Package Contents

1 MUHD44TP

2 Mounting ears

1 Power adapter (DC 24V 2.71A)

1 IR remote

1 Power cord

1 RS-232 cable

8 Captive screw connectors

4 table mount cushions

4. Front and Rear Panel Description

4.1 Front Panel Operation

No.

Name

Description

①

Firmware

Micro USB port for update firmware.

②

Power

Indicator

Keep light when power on.

③

IR Receiver

Receive control signal from IR remote.

④

LCD

Indicator

Real-time shows system status.

⑤

INPUTS/

buttons

Normal mode: Input buttons, ranging from "1" to "4".

Inquire mode: Press “AV”more than 3 seconds to enter this mode.

to change different menus, to change different channels.

⑥

Function

buttons

AV button: To transfer AV and IR signal synchronously by the switcher.

Example: To transfer both AV and IR signals from input channel No.1 to

output channel No.3.

Operation: Press buttons in this order “1”, “AV”, “3”.

ALL outputs button: To transfer one input to all outputs.

Example: To transfer both AV and IR signals from input channel No.1 to

all output channels.

Operation: Press buttons in this order “1”, “ALL”

EDID management button: manually capture and copy the EDID data from

an HDBaseT output device to input port. Do not use the Local HDMI

outputs.

Example: To capture and copy the EDID data from output channel No.4

to input channel No.2.

Operation: Press buttons in this order “EDID”, “2”, “4”

⑦

OUTPUTS

Output buttons, ranging from "1" to "4".

To control the matrix from the front panel controls do the following:

“Input Channel” + “AV” + “Output Channel”

“Input Channel”: Fill with the number of input channel to be controlled.

“Output Channel”: Fill with the number of output channels to be controlled.

TEK-MUHD44TP 4x4 HDBaseT Matrix

TEKVOX, INC. 3 www.tekvox.com

830.460.9099

4.2 Rear Panel Operation

No.

Name

Description

①

IR ALL IN

Input port for IR control signal, connect

with IR receiver, deliver IR signal to all

the HDBaseT ports to control the

remote devices.

②

HDMI INPUTS

HDMI input ports, 4 in total, type A

female HDMI connector, connect

with HDMI input source devices.

③

IR OUT

Connect with IR transmitter, to emit

the IR signal sent from the HDBaseT

ports of the far-end Receiver. These

IR OUT sockets make up an IR matrix

with the IR IN sockets on the

HDBaseT receivers, and all IR signals

can be switched synchronously with

the AV signal, or separately switched.

④

OUTPUTS

a. IR IN: Connect with IR receiver, fixed IR

input for the output, cannot be switched

separately. It makes up an IR bi-directional

transmission with the IR OUT on the

corresponding HDBaseT receiver.

b. COAX: HDMI de-embedded digital audio

output.

c. RS232: Serial port to communicate with the

RS232 port on corresponding HDBaseT

receiver. When controlled by HDBaseT

receiver, the communication protocol must

be the same with MUH44TPR2-N.

d. HDMI: HDMI output port, connect with HDMI

displayers, deliver same input signals with

HDBaseT ports, split HDMI output for local

monitoring.

e. HDBaseT: Works with HDBaseT receivers,

such as TPHD402PR. It can extend AV, IR

and RS232 signal to 70m distance.

Meanwhile, it can provide power for the

receivers which support PoC.

f. AUDIO: HDMI de-embedded stereo audio

output

⑤

IR EYE

Connect with extended IR receiver,

use the IR remote to control

MUH44TPR2-N.

⑥

TCP/IP

TCP/IP port for unit control

⑦

RS232

Serial port for unit control, 9-pin

female connector, connects with

control device such as a PC.

⑧

Power

Indicator

Illuminate red when powered on.

⑨

DC 24V

Connect with DC 24V power adaptor.

⑩

GROUND

Connect to grounding, make the unit

ground well.

4.4 HDBaseT Twisted Pair Cable Connection

Always use a minimum of 30 feet Cat 5E or Cat 6 solid twisted pair cable.

TIA/EIA T568A

TIA/EIA T568B

Cable

color

Cable

color

green

white

orange

white

green

orange

white

green

white

blue

white

blue

white

orange

green

brown

white

brown

white

brown

1st

Ground

4--5

1st

Ground

4--5

2nd

Ground

3--6

2nd

Ground

1--2

3rd

Group

1--2

3rd

Group

3--6

4th

Group

7--8

4th

Group

7--8

TEK-MUHD44TP 4x4 HDBaseT Matrix

TEKVOX, INC. 5 www.tekvox.com

830.460.9099

5. System Diagram

6. System Operation

6.1 Front Panel Button Control

Front Panel Button Control

MUH44TPR2-N provides with convenient front panel button control. Here we make a brief

introduction to the system operations.

Switching I/O connection

To convert one input to an output:

Operation: “input”+“output”+“ENTER”

Example: input 1 to output 2

Note: In default status, 4 IR OUT sockets correspond with 4 HDMI INPUTS. When you convert an

HDMI input to an output, the corresponding IR OUT will be switched synchronously.

To convert an input to several outputs:

Operation: “input” + “output” + “output” +… + “ENTER”

Example: Switch input 2 to output 2, 4

To convert an input to all outputs:

Operation: “input” + “ALL” + “ENTER”

Example: Convert input 1 to all outputs

Note: Indicators of the pressed buttons will blink green for three times if the conversion is done, then

it will be off. If the conversion failed, they will be off immediately.

EDID Management

MUH44TPR2-N features EDID management to maintain compatibility between all devices. It can be

controlled via EDID learning and EDID invoking.

EDID Learning (from output):

One input port learns the EDID data of one output port

Operation: Press “EDID”, “INPUTS”+“OUTPUTS”+“ENTER”.

Example: Input 2 learns EDID data from output 4

All input ports learn EDID data from one output port

Operation: Press “EDID”, “ALL”+“OUTPUTS”+“ENTER”

Example: All input ports learn EDID data from output 4

Note: Indicators of the pressed buttons will blink green for three times if the conversion is done, then

it will be off. If the conversion failed, they will be off immediately.

Table des matières

Autres manuels Tekvox Commutateur matriciel

Tekvox

Tekvox TekFlex-12 Manuel utilisateur

Tekvox

Tekvox TEK-MHD44TP 79055 Manuel utilisateur

Tekvox

Tekvox TekFlex-16 Manuel utilisateur

Manuels Commutateur matriciel populaires d'autres marques

Broadcast Tools

Broadcast Tools SS 8.2 Manuel utilisateur

Altimium

Altimium MATF32 Manuel utilisateur

ALFAtron

ALFAtron ALF-MUK44N Manuel utilisateur

Monoprice

Monoprice Blackbird 15377 Manuel utilisateur

Kramer

Kramer XL 3216VS Manuel utilisateur

PTN

PTN FMX12 Manuel utilisateur

CYP

CYP nT15GX01 Manuel utilisateur

Kramer

Kramer VP-2x2 Manuel utilisateur

Kramer

Kramer Sierra Video 6432V5xl Manuel utilisateur

TESmart

TESmart HMA0402A40 Manuel utilisateur

Octava

Octava HD4XSTPMX Manuel utilisateur

Intelix

Intelix FLX-88 Mode d'emploi

Kramer

Kramer LASSEN XL 3232S Manuel utilisateur

Roland

Roland XS-1HD Manuel utilisateur

Kramer

Kramer VS-66HDCPxl Manuel utilisateur

Atlona

Atlona AT-HDMI-22M Manuel utilisateur

Link

Link HD8X8 Manuel utilisateur

AMX

AMX AVS-OP-2020-117 Instructions et recettes