Tektronix DPO2014 Manuel utilisateur

DPO2000 and MSO2000 Series Oscilloscopes

Declassiﬁcation and Security

ZZZ

Instructions

www.tektronix.com

077-0108-00

or suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication

supersedes that in all previously published material. Speciﬁcations and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

TekSecure is a trademark of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.

Worldwide, visit www.tektronix.com to ﬁnd contacts in your area.

Table of Contents

Preface.............................................................................................................. iii

Clear and Sanitize Procedures...................... .............. .............................................. ... 1

Memory Devices............................................................................................... 1

Data Export Devices........................................................................................... 3

Built-In Security Features ......................................................................................... 5

When to Use TekSecure....................................................................................... 5

What TekSecure Does......................................................................................... 5

Disable the LAN Port and Clear LAN Ethernet Settings........... .............. ......................... 6

Disable the USB Device Port................................................................................. 7

Clear and Sanitize a Non-Functional Instrument........................... .......... ........................ ... 9

DPO2000 and MSO2000 Series Declassiﬁcation and Security Instructions i

Table of Contents

ii DPO2000 and MSO2000 Series Declassiﬁcation and Security Instructions

Preface

If you have data security concerns, this document helps you to sanitize or remove

memory devices from the DPO2000 and MSO2000 Series Digital Phosphor and

Mixed Signal Oscilloscopes.

The DPO2000 and MSO2000 series products have data storage (memory) devices

and data output devices (USB ports). These instructions tell you how to clear or

sanitize the memory devices, and also tell you how to declassify an instrument

that is not functioning.

Instrument code and calibration settings reside in nonvolatile ﬂash memory.

Instrument setups and reference waveforms may also be stored in ﬂashmemoryor

on USB drives connected to the instrument.

If you have any questions, contact the Tektronix Technical Support Center at

www.tektronix.com/support.

Products The following Tektronix products are covered by this document:

DPO2024

DPO2014

DPO2012

MSO2024

MSO2014

MSO2012

Related Documents The DPO2000 and MSO2000 Series Digital Phosphor and Mixed Signal

Oscilloscopes Service Manual, part number 071-2331-XX, is available on the

Tektronix Web site at www.tektronix.com/manuals.

DPO2000 and MSO2000 Series Declassiﬁcation and Security Instructions iii

Preface

Terms The following termsmaybeusedinthisdocument:

Clear. This removes data on media/memory before reusing it in a secured

area. All reusable memory is cleared to deny access to previously stored

information by standard means of access.

Erase. This is equivalent to clear.

Media storage/data export device. Any of several devices that can be used

to store or export data from the instrument, such as a USB port.

Nonvolatile memory. Data is retained when the instrument is powered off.

Power off. Some instruments have a “Standby” mode, in which power is

still supplied to the instrument. For the purpose of clearing data, putting the

instrument in Standby mode does not qualify as powering off. For these

products, you will need to either press a rear-panel OFF switch or remove the

power source from the instrument.

Remove. Thisisaphysicalmeanstoclearthedatabyremovingthememory

device from the instrument. Instructions are available in the product Service

Manual.

Sanitize. This eradicates the data from media/memory so that the data cannot

be recovered by other means or technology. This is typically used when the

device will be moved (temporarily or permanently) from a secured area to a

non-secured area.

Scrub. This is equivalent to sanitize.

User-modiﬁable. The user can write to the memory device during normal

instrument operation, using the instrument interface or remote control.

Volatile memory. Data is lost when the instrument is powered off.

iv DPO2000 and MSO2000 Series Declassiﬁcation and Security Instructions

Clear and Sanitize Procedures

Memory Devices

The following tables list the volatile and nonvolatile memory devices in the

standard instrument and listed options.

Table 1: Volatile Memory Devices for the DPO2000 and MSO2000 Series

Type and minimum size Function User modiﬁable

Data input

method Location To clear or sanitize

CMOS, SDRAM, 32MX16,

512MB DDR2, 1.8V, 333MHZ;

MT47H32M16CC-3, FBGA84

DDR memory: contains

the analog channel

waveform acquisition

data during operation

Only by the

processor system

N/A Acquisition board Remove power from the

instrument for at least

20 seconds

CMOS, SDRAM, 32MX16,

512MB DDR2, 1.8V, 333MHZ;

MT47H32M16CC-3, FBGA84

DDR memory: contains

the digital channel

waveform acquisition

data during operation

Only by the

processor system

N/A Acquisition board

(MSO2000 Series only)

Remove power from the

instrument for at least

20 seconds

CMOS, SDRAM, 64MX16,

1G DDR2, 1.8V, 333MHZ;

MT47H64M16BT-3, FBGA84

DDR memory: contains

the instrument code and

data during operation

Only by the

processor system

N/A Acquisition board Remove power from the

instrument for at least

20 seconds

CMOS, SDRAM, 32MX16,

512MB DDR2, 1.8V, 333MHZ;

MT47H32M16CC-3, FBGA84

DDR memory: contains

the instrument code and

data during operation

Only by the

processor system

N/A Acquisition board

(4-channel products

only)

Remove power from the

instrument for at least

20 seconds

Table 2: Nonvolatile Memory Devices for the DPO2000 and MSO2000 Series

Type and minimum size Function User modiﬁable

Data input

method Location To clear or sanitize

CMOS,FLASH;16MX8OR

8M X 16, 128MBIT, 75NS, 3V;

PC28F128J3D-75, BGA64

FLASH: contains the

instrument ﬁrmware,

calibration constants,

reference waveforms,

and instrument setups

N/A N/A Acquisition board To clear: Not applicable

for calibration constants.

Use the TekSecure

feature to erase

reference waveforms

and instrument setups.

Use the procedure to

disable the LAN Ethernet

and to clear information,

such as IP addresses.

(See page 6, Disable the

LAN Port and Clear LAN

Ethernet Settings.)

To sanitize: Remove

the acquisition board;

see the product service

manual for removal

instructions. Store the

removed board in a

secure area or destroy

it. Return the product

to Tektronix and a

new acquisition board

will be installed and

the instrument will be

repaired and adjusted as

necessary.

DPO2000 and MSO2000 Series Declassiﬁcation and Security Instructions 1

Clear and Sanitize Procedures

Table 2: Nonvolatile Memory Devices for the DPO2000 and MSO2000 Series (cont.)

Type and minimum size Function User modiﬁable

Data input

method Location To clear or sanitize

CMOS, CLOCK; SERIAL

REAL-TIME CLOCK,

CRYSTAL, 7 X 8 RAM, SPI,

3.3V; M41T93RMY, SO18.300

Real-time clock, with

battery backup

Only by the

processor system

N/A Acquisition board Not applicable; no user

data

CMOS, EEPROM; 128 X 8,

SERIAL; 24C01A, SOIC8

EEPROM: contains the

front end board serial

number and calibration

information

N/A N/A Front End Board Not applicable; no user

data

CMOS, MICROCONTROLLER;

8-BIT, 32K BYTES ON-CHIP

FLASH, MC9S08AW32CPUE,

LQFP64

Microcontroller with

FLASH: contains the

front panel processor

code and power status

for soft power switch

Only by the

processor system

N/A Front Panel Board Not applicable; no user

data

CMOS, EEPROM; 256 X 8,

SERIAL; 24C02, SO8.15

EEPROM: contains

the application module

ﬁrmware

N/A N/A DPO2000 and

MSO2000 application

module

Not applicable; no user

data

2 DPO2000 and MSO2000 Series Declassiﬁcation and Security Instructions

Clear and Sanitize Procedures

Data Export Devices

The following table lists the data export devices.

Table 3: Data Export Devices

Type and minimum size Function User modiﬁable

Data input

method Location To disable

USB host port Supports the removable

USB ﬂash drive; user

storage of reference

waveforms, screen

images, and instrument

setups

Yes Save USB host port on the

front of the instrument

Files can be deleted

or overwritten on the

instrument or a PC; the

USB ﬂash drive can be

removed and destroyed.

The USB host port

cannot be disabled.

USB device port Supports remote control

and data transfer to a

Yes Remote

control via

USBTMC

USB device port on the

rear of the instrument

Use the procedure to

disable the USB device

port. (See page 7,

Disable the USB Device

Port.)

DPO2000 and MSO2000 Series Declassiﬁcation and Security Instructions 3

Clear and Sanitize Procedures

4 DPO2000 and MSO2000 Series Declassiﬁcation and Security Instructions

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Tektronix Équipement de test

Tektronix

Tektronix 067-0587-01 Manuel utilisateur

Tektronix

Tektronix 585 Manuel utilisateur

Tektronix

Tektronix TDS5000B Series Manuel d'utilisation et d'entretien

Tektronix

Tektronix TBS2000 Series Manuel utilisateur

Tektronix

Tektronix 315D Series Manuel utilisateur

Tektronix

Tektronix TDS1000B Series Manuel utilisateur

Tektronix

Tektronix Keithley S500 Manuel utilisateur

Tektronix

Tektronix P6248 Manuel utilisateur

Tektronix

Tektronix S-4 Manuel utilisateur

Tektronix

Tektronix 454A Manuel de service

Tektronix

Tektronix 177 Manuel utilisateur

Tektronix

Tektronix TBS1000 Series Manuel utilisateur

Tektronix

Tektronix 4000 Series Manuel utilisateur

Tektronix

Tektronix SC 502 Manuel utilisateur

Tektronix

Tektronix 2213 Manuel utilisateur

Tektronix

Tektronix 7B70 Manuel utilisateur

Tektronix

Tektronix TDS 694C Manuel utilisateur

Tektronix

Tektronix 513 Manuel utilisateur

Tektronix

Tektronix 3 Series Guide de référence

Tektronix

Tektronix TDS 540 Manuel utilisateur

Tektronix

Tektronix 2465A Manuel utilisateur

Tektronix

Tektronix 543B Manuel utilisateur

Tektronix

Tektronix TBS1000C Series Manuel utilisateur

Tektronix

Tektronix WFM6100 Opt. MB Manuel d'utilisation et d'entretien

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur