the pack you want. If none of them match, pick any one of the four you want to change. In the next step, you will
be able to change the values to match your battery. Your setting will be automatically remembered the next time
you enter this menu. Press the right button when you have made your selection.
6You now have an opportunity to change the cell count. If the cell count is correct then simply press the right
button to continue. If not, you can change the cell count at this point by using the up or down button until
the cell count you want is displayed. Notice that holding the button down will rapidly advance through the
numbers. When the cell count you want is displayed press the right button to continue.
7You now have an opportunity to change the milliamps. For most Li batteries this is normally set to 1C or
basically the milliamp rating of the battery or less. If the milliamp charge rate is correct then simply press the
right button to continue. If not you can change the milliamps at this point by using the up or down
buttons until the milliamps you want is displayed. Notice that holding the button up or down will rapidly advance
through the numbers. When the milliamps you want is displayed press the right button to continue.
Start the Charge
8The Xtrema will give you one last chance to abort before charging. It will calculate the Li voltage based on cell
count and display the charge current that you have selected. DO NOT MISS THIS LAST OPPORTUNITY TO
CHECK YOUR SETTINGS. Wrong settings may cause LI batteries to burst into FLAMES! If all is OK , then
start the charge by pressing the right button to continue. You may abort the charge at any time by pressing
any key . When the charge has terminated, either by a fail mode, user abort, or successful completion,
the display will freeze with the terminating values and the STATUS code will appear at the top right of the LCD.
You may hit any key to go back to the Update Memory display. You may then start another charge
cycle (starting at step 6) or you may press the leftbutton to return to the main menu. In an emergency you may
rapidly pull out the battery to stop a charge. However, this is NOT a recommended way to abort the charge.
Using the Wattmeter
Connect the Xtrema in between battery and motor
1. Connect the red (+) and black (-) Xtrema directly to a 12Volt automobile battery or regulated power supply. Be
careful to observe polarity.
2. Connect the Li battery to the connector labeled “BATTERY”
3. Connect your speed controller and motor to the connector labeled “MOTOR”
4. You may optionally connect the temperature probe to the battery or your motor using the hook andloop strap for
monitoring purposes.
Set to Wattmeter mode
5. “Wattmeter”should be selected on the display. (If not push the up or down buttons on the joystick until it is
selected.) Press the joystick to the right to enter Wattmeter mode.
6. You are now able to measure Watts, amps, volts, temperature and even horsepower. Pressing the right
button will allow you to toggle into the [STORED] mode which will display peak amps, minimum voltage, max
temperature as well as the calculated watts and horsepower.
7. Press the leftbutton to return to the main menu.
WARRANTY
LIMITED WARRANTY
The Xtrema is warranted to the original purchaser for 3 years from the date of purchase to be free from defects in material and workmanship. During this period Tejera Microsystems
Engineering Inc. will repair or replace, at their discretion, the defective unit. Warranty is not transferable and is therefore limited to the original purchaser of the unit, This warranty does not
apply to any unit which has been abused, improperly installed, improperly used, used for purposes other than those purposes for which the unit was designed, handled roughly, damaged in
shipment, nor to any unit which has been altered or repaired by unauthorized personnel. Under no circumstances will the buyer be entitled to incidental or consequential damages. Warranty
coverage also requires proof of purchase date unless ordered direct from the manufacturer. This Limited Warranty gives you specific legal rights; you may also have other rights which vary
from state to state.
WARRANTY PROCEDURE:
A minimum charge of $7.00 to cover shipping and handling is required on all returned units after the first 30 days, and should be enclosed with the unit. Be sure to enclose your Bill of Sale
as proof of purchase with the unit. (A legible photocopy is acceptable.) In the event that the work is not covered under the warranty, TME will attempt to contact the owner unless special
instructions or a credit card number are received with the unit.
FREE LIFETIME UPDATES: The Xtrema carries free firmware updates for the life of the product. For your convenience, downloadable updates will be made available online at
www.theXtrema.com or www.TMEnet.com . Activate your warranty online to receive product updates and upgrades! Go to: www.TMEnet.com/register A special data cable will be
required for your computer to connect to the Xtrema (not included) Alternately you may return the Xtrema to us with $7.00 for return shipping to be updated at no charge.
REPAIRS:
For out of warranty repairs the standard repair fee per unit is up to 50% of the current list price plus $7.00 shipping and handling charges. You may prepay by check, MO, VISA, MASTER
CARD or DISCOVERY
ALL RETURNS MUST BE SENT TO: Tejera Microsystems Engineering, Inc., 11705 Boyette Rd #418, Riverview, Florida 33569 carefully pack and ship the unit via the post office, UPS or
FED EX, fully insured and prepaid.
