TECO L510 Manuel utilisateur

Page 1 of 7 12/06/13

TECO L510 Inverter

Quick Start Guide

1) Ensure that the Inverter & the motor have the correct

KW power and voltage ratings.

Motor full load amps must not exceed the Inverter rating.

2) Ensure that the supply & Motor cables are connected

Correctly prior to power up.

3) For single phase supply, use L1& L3 ( N) on units which

have 3 supply terminals.

On units with two supply terminals L1&L2, connect live to L1

and Neutral to L2.

4) Connect motor cable to terminals T1,T2 &T3.

(Swap two leads If motor runs in reveres direction).

5) Connect supply Earth and the motor Earth to the drive Earth

terminal.

Note:-

I ) For detailed installation

and wiring refer to the

Instruction manual.

This guide is to assist you in installing and running the inverter and verify that it is

functioning correctly for it’s main and basic features.

For detailed information and if there are any doubts please refer to the instruction manual.

Step 1 Supply & Motor connection

Page 2 of 7 12/06/13

Apply power to the drive, the display will briefly show the supply voltage

220V followed by flashing.

This is the default ( factory set) frequency.

If the unit has been used previously then it will show the last frequency

programmed.

Step 2 Apply power to the drive

05.0

Step 3 Test run from keypad

Press RUN KEY to run.

The frequency will ram up to 5.0 Hz or the user pre-set frequency and

according to the default acceleration ramp time.

Press STOP/RESET key to stop.

The frequency will ramp down to zero according to the default decel ramp

time.

Step 4 To alter frequency from keypad. (Default setting).

Use the Arrow keys and </ Enter

To alter the digits to the required frequency.

eg. 50.0 HZ then use RUN and STOP keys to start/ stop.

Page 3 of 7 12/06/13

Remote speed reference and Remote run

1) Ensure that you have carried out installation & wiring requirements as

per step1 quick start guide on previous page before you proceed.

2) For analogue signal type 0-10V dc. Use the terminal AVI.

For analogue input type 4-20 mA.dc. Use the terminal ACI.

.Connect remote potentiometer OR remote 0-10 vdc signal as required.

to terminals AVI.

Terminal 10Vdc is the supply provided for use with the potentiometer.

Terminal AVI for potentiometer wiper connection.

Terminal AGND is 0Vdc.

3) Connect remote start switch if required according to diagram in the

instruction manual.

Use terminals +12Vdc & S1 (Forward run).

Use terminals +12Vdc & S2 (Reverse run)

+12Vdc is the common terminal for PNP type inverters.

COM (0Vdc) terminal is common for the NPN type inverters.

Step 1 Remote mode wiring. Speed reference and Run signals.

Step 2 Remote mode Run

1) Power up.

Display will read the frequency from one of the following according to the

Connection made to AVI terminal. Set parameter 00-05 =00-02

a) Remote external potentiometer

b) Remote 0-10VDC analog signal.

Step 3 Check/ verify and alter parameters

Check / verify and alter parameters for remote start & remote frequency

as necessary before you proceed. Parameters 00-02 & 00=05

See quick start parameter list & How to alter parameters.

Page 4 of 7 12/06/13

How to alter parameters

Step 4 RUN using remote speed reference.(Potentiometer,0-10vdc or 4-

20ma

)

1) To run. Activate the remote run switch connected to terminals

S1 ( FWD) or S2 ( REV) as required,. Parameter 00-02=00-01

The frequency will ram up to the frequency set on

the pot ( parameter 00-05 = 00-01 ) or

analog signal (0-10v dc /4-20ma) and according to the set

acceleration ramp time.

How to alter parameters using the keypad

1) To alter parameters:- Press the MODE key,

until the first parameter 00-00 is displayed.

2) Then use the arrow keys to select the parameter required then

Press < / ENTER key to read the preset value.

3) Use the and < / ENTER keys to alter the setting of the

parameters as per basic quick start parameter list.

Note:- For full parameter list refer to the instruction manual.

4) To save each parameter change, press < / ENTER key then

the word END will be displayed.

5) Use key to select the next parameter to alter and

follow steps 2 to 4 until all changes are complete.

6) Pressing the MODE key repeatedly will alternate the display

between the preset frequency ( flashing display) and the last parameter

accessed or other selectable displays 0 to 7 when selected by parameter

12-00 according to the table below.

【0】:Disable display 【1】:output Current

【2】:output Voltage 【3】:DC voltage

【4】:Temperature 【5】:PID feedback

【

】

:AVI

【

】

:ACI

Page 5 of 7 12/06/13

Basic Quick Start Parameter List

Parameter Default Range Note

00-14 10.0 0.1~3600.0 Acceleration time in Secs

00-15 10.0 0.1~3600.0 Deceleration time in Secs

00-04 000 0-2 0: Forward/Stop-Reverse/Stop

1: Run/Stop-Reverse/Forward

2: 3-Wire Control Mode-Run/Stop

00-12 50/60Hz

0.01~650.00

Max frequency limit.

00-13 0.0 0.00~649.00

Min frequency limit

00-02 00-00 0-2 Start mode:-

Keypad = 00-00

Remote = 00=01

Communication = 00-02

00=05 00-00 0-6

00-00 = keypad

00-01= Potentiometer on keypad

00-02= External AVI analogue signal

00-03= External ACI analogue signal

00-04 =External up/down frequency control

00-05= control by Communication method

00-06=PID output

07-09 000 0-1 Stop method:- 00-00 = Decel to stop

00-01= Coast to stop

02-01 **A **A Motor overload protection

13-08 000 Set to factory setting.

1150 = 50 HZ system.

1160 = 60HZ system

Note:- For Full Parameter List see the Instruction manual

Page 6 of 7 12/06/13

Interconnection Diagram.

Single phase (PNP):

AC Power

source

L1(L)

+12V

Frequency

reference or PID

Multi-function input

Fuse

Inverter

output

Ground

Main

Switch

Power

input

RS485

1:A+

2:B-

3:A+

4: RX

5: TX

6:B-

7:VCC

8:A

Pin1 to Pin 8

AGND

L3(N)

Multi-function output

0~10V / 4~20mA

CON2

10V

AVI (0~10V)

ACI (0~20mA)

AGND

Relay output

250VAC/1A

(30VDC/1A)

Model:

200V : L510-2P2-H1F-P / L510-2P5-H1F-P / L510-201-H1F-P

L510-202-H1F-P / L510-203-H1F-P

Note:- Supply voltage must not be connected to Inverter output terminals

T1,T2 ,T3. This will damage the inverter.

Page 7 of 7 12/06/13

Three phase (NPN):

AC Power

source

L1(L)

COM

Frequency

reference or PID

Multi-function input

Fuse

Inverter

output

Ground

Main

Switch

Power

input

RS485

1:A+

2:B-

3:A+

4: RX

5: TX

6:B-

7:VCC

8:A

Pin1 to Pin 8

AGND

Multi-function output

0~10V / 4~20mA

CON2

10V

AVI (0~10V)

ACI (0~20mA)

AGND

Relay output

250VAC/1A

(30VDC/1A)

L3(N)

Model:

200V : L510-2P2-H3-N / L510-2P5-H3-N / L510-201-H3-N

L510-202-H3-N / L510-203-H3-N

Autres manuels pour L510

Table des matières

Autres manuels TECO Onduleur

TECO

TECO L510S Series Guide d'installation

TECO

TECO 7300EV Manuel utilisateur

TECO

TECO L510S Series Manuel utilisateur

TECO

TECO 7200 MA Series Manuel utilisateur

TECO

TECO N3 Series Manuel utilisateur

TECO

TECO JNTHBCBA0001BEAU Manuel utilisateur

TECO

TECO A510s Manuel utilisateur

TECO

TECO PA7300 Manuel utilisateur

TECO

TECO N3 Series Manuel utilisateur

TECO

TECO F33 Series Manuel utilisateur

TECO

TECO L510 Manuel utilisateur

TECO

TECO e510 series Manuel utilisateur

TECO

TECO E510s Series Manuel de l'opérateur

TECO

TECO MV510 Series Manuel utilisateur

TECO

TECO A510-2001-H Manuel utilisateur

TECO

TECO e510 series Manuel utilisateur

TECO

TECO SPEECON 7200GS Manuel utilisateur

TECO

TECO L510S Series Manuel utilisateur

TECO

TECO A510s Manuel utilisateur

TECO

TECO JN5-CM-USB Manuel utilisateur

TECO

TECO A510s Instructions d'utilisation

TECO

TECO E510s Series Manuel utilisateur

TECO

TECO L510S Series Manuel utilisateur

TECO

TECO FM50 Series Mode d’emploi

Manuels Onduleur populaires d'autres marques

Fourgroup

Fourgroup Easy Manuel utilisateur

Velleman

Velleman PI300M Manuel utilisateur

Sungrow

Sungrow SG350HX-US Manuel utilisateur

WilTec

WilTec 61897 Manuel utilisateur

SMA

SMA SUNNY BOY STORAGE 2.5 Manuel utilisateur

Simplicity

Simplicity LANDLORD 316 Manuel utilisateur

Santak

Santak SMAX 3000 Manuel utilisateur

ATON

ATON RA.Store-3 Manuel utilisateur

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuel utilisateur

Tektronix

Tektronix CFG250 Manuel utilisateur

Champion

Champion 200989 Manuel utilisateur

Vanner

Vanner 20-500 Series Manuel utilisateur

GE GEP Manuel utilisateur

Astrel Group

Astrel Group Power Reducer Guide rapide

MULTIQUIP

MULTIQUIP GDP-5H Mode d’emploi

GoWISE

GoWISE PS1007 Manuel utilisateur

Promate

Promate PM13500D ES Manuel utilisateur

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuel utilisateur