Tecnoalarm TecnoFire TFNET Manuel utilisateur
by
Installation
Document version 0.3
FW version 1.0.00
HW version TFNET
Setup SW version 5.2
Update date 12/2016
Language English
TFNET
Communication interface
TFNET
2
TFNET - TFAXFIRE Systems Compatibility
TFA1-298 Ver. 1.3.09 TFA2-596 Ver. 1.3.09 TFA4-1192 Ver. 1.3.09
TFNET 3
CONTENTS
1 - OBLIGATIONS AND REQUIREMENTS
5
2 - MAINTENANCE
7
3 - TECHNICAL SPECIFICATIONS AND FUNCTIONS
9
4 - INSTALLATION NOTES
4.1 Assembly view 11
4.2 Installation 12
4.3 Connection cables 12
5 - USER INTERFACE
5.1 Front panel 13
5.2 LED 13
6 - OPERATING MODES OF THE SYSTEM
6.1 Access levels and codes 15
6.2 Access level 2 16
6.3 Functioning test 16
7 - ELECTRONIC BOARD
17
8 - SOFTWARE OPTIONS
19
9 - FIRMWARE UPGRADE
21
TFNET
4
TFNET 5
Introduction
Attention: Before installing the TFNET communication interface: carefully read this manual; it contains important information and
warnings on the installation modes which must be observed.
Operating limits and purposes of the fire detection systems
It is essential to know that a fire detection system does not ensure protection and immunity against damage of any kind and
amount, generated by or deriving from fires.
It is essential to begin by stating that any fire system in charge of detection, extinguishing, actuations, evacuation etc. must
be installed and maintained in its best working order, according to the instructions provided by the manufacturer and/or by the
designer.
Tecnofire fire detection systems can promptly notify the personnel in charge about the occurrence of dangerous fires. The system
can also automatically handle the events and then, according to the setup mode: broadcast messages urging the evacuation of the
premises, enable automatic remote control systems, CCTV systems, extinguishing systems, stop all situations and events that may
feed the fire, in order to preserve the safety of persons and of the premises and assets contained in them.
Cautions and warnings
This document contains the procedures required to perform a successful installation of the product. However, the interpretation
and correct application of its contents cannot be separated from the necessary training of the technical staff, responsible for the
installation of the products covered by this manual.
In particular, the technical staff in charge of installation should have the necessary basic technical preparation, should know and
properly apply the regulations in force, relating to the installation of fire protection systems, and more generally should know all the
regulations in force concerning plant standards, installation, maintenance and electrical safety.
Moreover, the technical staff must have a thorough knowledge of the product, acquired attending specific training courses, at the
premises of Tecnofire (fire systems division of Tecnoalarm S.r.l.).
Environmental requirements
The TFNET communication interface must be installed within structures or buildings with climate characteristics of temperature
and humidity (non condensing), that do not exceed the values reported in the homologation of the products. The specific values of
operating temperature and humidity of the Tecnofire products can be found in the relevant technical specifications tables.
Usage requirements
To avoid damage, or even risky malfunctions, in the management of the devices designed to control devices and systems
operationally dependent from the TFNET communication interface, it is compulsory to use only the components and devices
indicated by Tecnofire. The interface with complementary systems manufactured by third parties must be realized with Tecnofire
input and output modules, making sure each time of the correct functional fit. If in doubt, always refer to the Tecnofire technical
support service.
Technical service
The Tecnofire technical service is always at your disposal to solve technical issues related to installation, clarify product features
and application of Tecnofire products.
Power sources
During system planning, it is important to take into account that the autonomy of operation required by the legislation is respected,
properly sizing the primary power source (from mains) and the secondary power source (backup batteries). Please note that in
case of mains power outage, the system ensures its operation using the backup batteries for a limited time.
Induced damage
Before working on any component of the System, to avoid damage to the equipment during installation and in all subsequent
maintenance works, it is always necessary to disconnect all primary power sources (mains) and secondary power sources (backup
batteries) of the system. To avoid damage caused by electrostatic voltage, always carefully handle the electronic cards of the
devices, avoiding touching the electronic components directly.
1 - OBLIGATIONS AND REQUIREMENTS
TFNET
6
TFNET 7
2 - MAINTENANCE
Periodic maintenance of the system
For perfect efficiency of the fire detection system, the customer shall provide for a preventive maintenance program. The
frequency of inspections depends on several factors; it is recommended to perform an inspection on average every 6 months
(unless specifically required otherwise). Maintenance should be carried out by specialized personnel provided with the necessary
know-how and equipment to perform adequate maintenance work. It is assumed that the information needed to perform a proper
maintenance can be provided by the designers and/or manufacturers the fire detection system.
The maintenance guidelines are provided in the Italian standard UNI 11224.
The most significant checks should include at least:
• Functional state of power supply units and accumulators (APS) of the control panel and of the system power supply modules.
• State of the batteries of the self-powered devices (sirens, communicators).
• Functional tests of the sensors that make up the system.
• Checks about the state of cleanliness of the analysis chambers of the optical sensors.
• Efficiency of the control organs of the control panel and repeaters.
• Functional and operational efficiency of the acknowledgement, evacuation and system recovery procedures.
• Efficiency of manual alarm button module.
• Efficiency of optical and acoustic notification module.
• Efficiency of phone communicators (phone call tests).
• Verification of system actuations entrusted to input and output interface modules, etc.
• Check for correct tightening of the terminals wires.
• Final drafting of a test report signed by the maintainer and by the customer for acceptance.
TFNET
8
TFNET 9
3 - TECHNICAL SPECIFICATIONS AND FUNCTIONS
Electrical
specifications
Power supply Over serial bus
Rated voltage 24V DC
Operating voltage 20V…27.6V DC
Stand-by consumption 90mA @ 24V DC
Max. consumption 140mA @ 24V DC
Physical
specifications
Operating temperature -5°C...+40°C
Relative humidity
(non-condensing) 10%...93%
Protection class IP30
Casing ABS V0
Dimensions (L x H x D) 165 x 110 x 41mm
Weight 200g
Conformity
Directive R&TTE 1999/05/EC
class 1/TTE
Standards EN 50136-1-1
EN 50136-2-1
Approved for use with TFA1-298, TFA2-596 and TFA4-
1192 control panels
General
specifications
Model TFNET
Description Ethernet interface
Protocol Fire-Bus
Address programming Dip-switch
Connection RS485
IP node
Class Standard 803.2 - ATE4
Ethernet channels
Server 1
Server 2
Tecnoserver
Tecnoalarm
Service Tecnoalarm
Tecno Out (optional)
Modbus (optional)
Channels 8
Transmittable events 33 categories
Transmittable zone events 5
Telephone numbers/
IP address
2 per channel
(max. 24 digits)
Call event queue 64 events
Communication protocols 10
Automation Test call with TCP/IP ✓
TFNET
10
Table des matières
Autres manuels Tecnoalarm Alarme incendie
