TechOne Hobby Air Titan EPO Manuel utilisateur

AIR TITAN

EPO

Our model kits are subject to constant quality checks throughout the production process, and we sincerely

hope that you are completely satisfied with the contents of your kit. However, we would ask you to check all

the parts before you start construction, referring to the Parts List, as we cannot exchange components which

you have already modified. If you find any part is not acceptable for any reason, we will readily correct or

exchange it once we have examined the faulty component. Just send the offending part to our Model

Department. Please be sure to include the enclosed complaint form, duly completed. We are constantly

working on improving our models, and for this reason we must reserve the right to change the kit contents

in terms of shape or dimensions of parts, technology, materials and fittings, without prior notification.

Please understand that we cannot entertain claims against us if the kit contents do not agree in every

respect with the instructions and the illustrations.

AIR TITAN

This is a sophisticated hobby product and is NOT a toy. It must always be operated with caution,

common sense and some basic mechanical ability. This manual provides instructions as

the assembly, safe operation and maintainence of this hobby product. It is highly

recommended that you follow and read fully the instructions and warnings stated in this

manual including, safety, assembly, set-up and flying guidelines in order to operate this

product correctly and avoid damage or serious injury.

1. Fuselage 1pc

2. Right wing 1pc

3. Left wing 1pc

4. Elevator 1pc

5. Rudder 1pc

6. Equipment cabin 1pc

7. Nose covering 1pc

10 11

20 21

8. Wing conn e c t e d batten 1 1p c

9. Plas t i c cove r o f win g t rail i n g edge 1 p c

10. Plastic cover of wing leading edge 1pc

11. Wing connected batten2 1pc

12. Landing gear 1pc

13. Screw（ M3*10mm） 4pcs

14. Screw（M2*14mm） 2pcs

15. Screw（M4*70mm ） 2pcs

16. Screw （M4*65mm ） 2pcs

17. Screw （M4*50mm） 2pcs

18. Screw （M3*45mm） 2pcs

19. Spinner 1pc

20. Pushrod1 4pcs

21. Pushrod2 2pcs

22. Propeller14*7 1pc

The RTF include

AIR TITAN

RTF

AIR TITAN Specification

63 in (1600 mm)

50.7 in (1287 mm)

5.24 lb-5.39 lb(2380g-2450g)

SF1470 prop

AIR TITAN 1600

1600mm big trainer that can take off/landing on ground, water and snowfield. It's also a good

plane for night flying.It has LED setting.

1.A good trainer in very big wingspan 1600MM, with good resistance easy control and carry.

2.Fuselage main reforcement batten construction,wing fixed construction,landing gear install

construction,motor install construction,and tow system construction,they are associated

skillfully and ensure the strength of the whole plane.

3.Use the design of tailwheel aircraft, and material of landing gear have been thickened,ensure

the stability and durability when take off and landing. Meanwhile the tailwheel linked with

rudder,and can control well the flying stance.

4.Can be easily changed to different taking off/landing mode, including ground, snowfield and

water.

5.You can install led strips on pre-reserved slots for night flying. It's very easy to operate.

6.Has enough power to tow a glider while flying. A tow construction that controlled by servo is

designed.

7.We use simple and reliable bolt way of Battery cabin and set at fuselage Abdomen,it's very

easy to change battery.

8.Use T-Motor 3520,ensure the strong power of the plane.

9.Most of the assemble step have been finished at factory,people can enjoy the flying very

easily. Solid packaging,simple assemble,easy flying, and high cost performance, it's really

good news for many model beginner.

AIR TITAN

Battery

4S 14.8V 3300mAh

25C Li-Po

Motor

AS3520

KV 680

ESC

50A

With BEC

Servos

17g servo

9g servo

Charger

B6 2 cells to 6cells

Li-Po Charger

Receiver

SR-7

7-channel receiver

Transmitter

T-6 2.4G

Charging the Flight Battery

DC Input cable

AC Input cable

Charger

Output cable

1.Connect temporary B6 charger,there is one LED green light, choose battery

type through pressing down the red button,switch two LED light bright. Once

choose Lipo,Lipo LED light green; Choose NiMh,NiMh LED light green.

2.Connect the charger of 4S battery pack,meanwhile connect output port of

battery to charger through output cable.Press the red button and loose the

button after LED light changed from green to red. The battery is charging.

3.When LED light turn from red to green,4S battery pack charge complete.

CAUTION: When connecting the battery to the battery charger, make sure the

two connectors are correctly oriented. Failure to do so could cause the battery

terminals to short, resulting in ﬁre, which could lead to property damage and

injury.

Specification

Operating voltage range: AC 110V-240 V, DC 11V-18V.

Charge power: 50Watts

Charge current range: 0.5-5.0A

LiPo battery cont: 2-6 cells

NiMh battery cont: 1-15 cells

Size: 130 mm * 90mm * 40mm

Weight: 355 g

Charging Warnings

·By handling, charging or using the included Li-Po battery, you assume all risks

associated with lithium batteries.

·If at any time the battery begins to balloon or swell, discontinue use immediately.

If charging or discharging, discontinue and disconnect. Continuing to use, charge

or discharge a battery that is ballooning or swelling can result in ﬁre.

·Always store the battery at room temperature in a dry area for best results.

·Always transport or temporarily store the battery in a temperature range of 40–

120º F (5–49º C). Do not store battery or aircraft in a car or direct sunlight. If stored

in a hot car, the battery can be damaged or even catch ﬁre.

·Always charge batteries away from ﬂammable materials.

·Always inspect the battery before charging and never charge dead or damaged

batteries.

·Always disconnect the battery after charging, and let the charger cool between

charges.

·Always constantly monitor the temperature of the battery pack while charging.

·Never discharge Li-Po cells to below 3V under load.

·Never leave charging batteries unattended.

·Never charge batteries outside recommended levels.

·Never attempt to dismantle or alter the charger.

·Never allow minors under the age of 14 to charge battery packs..

·Never charge batteries in extremely hot or cold places (recommended between

40–120° F or 5–49° C) or place in direct sunlight.

Transmitter

Mode 1

LED

CH5

Rudder/

Elevator

Trim

Rudder

Trim

Throttle

Trim

CH6

Throttle/

Aileron

Trim

Power

Switch

Mode 2

LED

CH5

Rudder/

Elevator

Trim

Rudder

Trim

Throttle

Trim

CH6

Throttle/

Aileron

Trim

Power

Switch

Installing the Transmitter Batteries

Insert included batteries in the transmitter

CAUTION: If using rechargeable batteries, charge only rechargeable batteries.

Charging non-rechargeable batteries may cause the batteries to burst, resulting

in injury to persons and/or damage to property.

CAUTION: Do not pick up the transmitter by the antenna. Do not alter or put weight

on the antenna. Damage to antenna parts can decrease transmitter signal strength,

which can result in loss of aircraft control, injury or property damage.

Fly control

For smooth control of your aircraft, always make small control moves. All directions

are described as if you were sitting in the aircraft.

For example, when the aircraft's nose is pointing toward you, left steering (rudder)

will turn the aircraft left (your right while holding the transmitter).

Mode 1

Throttvle

Speed

Elevator

Rudder

Aileron

Model 2

Throttle

Speed

Elevator

Rudder

Aileron

11 12

·Flying faster or slower: When your aircraft is stable in the air, push the throttle

stick up to make the aircraft go faster, and pull the throttle stick back to slow down.

The aircraft will climb when the throttle is increased.

·Elevator up and down: Push the elevator stick forward to make the aircraft go

down and pull the elevator stick back to go up.

·Steering right and left: Move the rubber or aileron stick right to make the aircraft

go right and move the rubber or aileron stick left to go left (as if you are seated in

the cockpit).

Flight Trimming

Elevator trim:

Only trim the aircraft at half throttle. When trimmed correctly, your aircraft climbs

steadily at full throttle and will ﬂy level at half throttle.

·When the aircraft's nose drifts up or down while the elevator stick is at

neutral (centered) position, push the elevator trim button by one or two “beep”

increments OPPOSITE the direction of drift.

·Adjust trim so the aircraft ﬂ ies straight and level when the elevator stick is

neutral.

Rudder trim:

·When the aircraft drifts left or right while the rudder stick is at the neutral position

(centered), push the rudder trim button by one “beep” increments OPPOSITE the

direc-tion of drift.

·Adjust trim so the aircraft ﬂies straight when the control stick is neutral.

Aileron Trim

·When the aircraft roll left or right while the aileron stick is at the neutral position

(centered), push the aileron trim button by one “beep” increments OPPOSITE the

direc-tion of drift.

Steps of ASSEMBLY

1.Install the landing gear on corresponding slot of fuselage, and fix with two pcs

screws.

1413

2.Insert elevator and rudder on the corresponding slot of fuselage,meanwhile

ensure to insert the tail wheel steel wire to the corresponding slot of rudder, and

fix with two pcs screw.

3.Take out 2 thread from wing(the female head which connect the airleon and

flap wing)

4.Insert the thread of airleon servo and flap servo into the corresponding slot of left

wing, and put the servo on the slot.

5.Fix the airleon servo and flap servo on left wing with screw.

15 16

6.Cross pushrod1 on servo arm.

7.Fix the pushrod 1 servo arm on the servo, put one head plastic clip of pushrod1

and fix on servo with screw.

8.Connect the airleon servo thread and flap servo thread(male head) to corresponding

female head.

9.Insert the connected thread into the corresponding slot.

10.Repeat the left wing installation steps from 3 to 9, and install right wing well.

17 18

11.Connect right and left wing through wing connected batten

12.Install elevator servo and rudder servo in the correspoding slot of fuselage with

screw.

13.Cross pushrod2 on servo harm.

14.Put and fix the servo arm with pushrod2 on servo.

15.Installed one clip head of pushrod2 on rudder servo arm, fix on rudder with screw.

Table des matières

Autres manuels TechOne Hobby Jouet

TechOne Hobby

TechOne Hobby SUPER-E 08300 Manuel utilisateur

TechOne Hobby

TechOne Hobby Slider Manuel utilisateur

TechOne Hobby

TechOne Hobby FPV Kraftei 650 EPO Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur