To delete a user (Manager only)
If a user’s code is no longer required it can be deleted
Press and hold 3 until a double beep sounds
Enter the manager code
Enter the user ID number from 1-9. A double beep
will sound to confirm deletion of the user.
To disable all users (Manager only)
All users can be temporarily be disabled without
deleting their codes
Press and hold 2 until a double beep sounds
Enter the manager code
A double beep will sound to confirm that all users have
been disabled.
To enable all users (Manager only)
If all users have been disabled, their codes can be re-
enabled
Press and hold 2 until a double beep sounds
Enter the manager code
A double beep will sound to confirm that all users have
been enabled.
To check user status (Manager only)
The status of users, whether activated or deleted can
be checked
Press and hold 7 until a double beep sounds
Enter the manager code, a double beep will sound
Press each user ID in turn
A double beep indicates the user is active
A single beep indicates the user is deleted
Press 0 to leave the menu
Checking user status operates if all users are disabled
or enabled.
To audit the lock (Manager only)
Full technical instructions for taking an audit are
available with the audit software. The command
required on the lock is:
Press and hold 7 until a double beep sounds
Enter the manager code
Firmly hold a DS1996 Dallas iButton to the Dallas
reader until a double beep sounds.
To add time delay values (Manager only)
Press and hold 9 until a double beep sounds
Enter the manager code, a double beep will sound
Enter 2 digits to indicate the time delay period 01-99
minutes. Enter 2 digits to indicate the open window
period 01-19 minutes. A double beep will sound
Re-enter the 4 digits to confirm
A double beep will sound to confirm that the values
have been set.
To change time delay values (Manager only)
To increase time delay values follow the steps in “To
enter time delay values”.
To decrease or remove time delay values, the operation
must be performed during the open window before the
user or manager code is entered. To decrease, follow
the steps in “To enter time delay values”
To remove:
Press and hold 9 until a double beep sounds
Enter the manager code, a double beep will sound
Enter 00 to indicate the time delay period should be
0 minutes. Enter 01 to indicate the open window
should not be operational. A double beep will sound.
Re-enter 0001 to confirm.
A double beep will sound to confirm that values have
been set. The open window will continue.
Optional Feature –Dual Mode
If the lock has been supplied in dual mode, user 1 is
installed with the default code 1-1-1-1-1-1.
To open the lock
Two valid codes must be entered to open the lock, one
of which can be a manager code.
To open the lock when time delay is active
One code is required to start time delay, and two codes
are required to open the lock during the open window.
User 9 may override time delay with a single code.
To perform a manager function
A valid user code must be entered before following the
standard manager function procedure.
Optional Feature –Alarm signals
To enter a duress code
If the feature has been enabled, a duress code can be
entered which will open the lock and also send a silent
signal to the alarm system to notify others that the lock
is being opened under duress.
The duress code is the user’s normal code, but the last
digit should be increased by 1, for example:
Normal code: 1-2-3-4-5-6
Duress code: 1-2-3-4-5-7
If the last digit is a 9, it should be changed to 0
If time delay is active, either the first code to initiate time
delay, or the code entered during the open window can
be duress codes.
If the lock is supplied in dual mode, either or both codes
can be duress codes.
Signals if remote block is active
If the lock system is connected to an alarm and an input
signal is received, the lock will sound a long beep after
entry of a valid code to indicate that it is disabled from
opening.
