Technetronix BMW09CIC Manuel
Your best partner for better driving
Update Date
2014.09.18
Model
QPI-BM09-1402-011
Firmware Date
BMW09CIC
Technetronix
Warning
When installing the main unit, do not remove or alter existing
vehicle fasteners, including nuts, bolts, screw, clips, and fittings.
Never detach, move or alter existing vehicle wiring, including
electrical grounds and straps. Alteration of existing vehicle
components may make vehicle unsafe to operate. Should be
no any electronic devices or magnetic pole around installation
place.
Air bags are vital part of a safety system. Never install main unit
in a way which will alter air bag wiring or interfere with air bag
deployment. Air bags must function properly in the event of an
accident.
Before installing, check the location of pipe, tank, electrical
cables and others.
Read and follow the instruction manual.
Wiring location must not interfere driving, get in or out from car.
Use electrical tape to insulate the ends of all wires, even if they
are not used. Proper insulation prevents arcs, shocks and fires.
When installation is complete, test all vehicle electrical systems
to ensure they operate correctly, including lights, horn, brake
lights, and emergency flashers.
According to our sales policy, any problems caused by user’s
mistake, careless can not be guaranteed.
Caution
All steps of installation should be done by well-trained specialist.
During installation ignition key should be taken off and after all
installation finish connect power cable with interface for the last
step.
Do not install the main unit in places where it ma be exposed to
dew condensation (around the air conditioning hose, etc), or in
locations where it may come in contact with water, high levels of
moisture, dust or oily smoke
Install wiring in a manner in which cables will not come in contact
with metal parts. The wiring may be damaged by contact with
metal parts, resulting in fire and shocks. Avoid all contact with hot
surfaces when wiring the main unit. High temperatures may
damage wiring, causing shorts, arcing and fires.
Kindly check all parts are in the box, when receiving the product, if
anything missing, inform to the supplier or manufacturer.
Warning / Caution
Table of Contents
1. Specifications
1.1 Main Specifications
1.2 Features
1.3 System Diagram
1.4 Components
1.5 Exterior
2. Installation
2.1 Installation Diagram
2.2 Installation
3. Settings
3.1 DIP Switch
3.2 Remote Control
3.3 Car Model and Navi Model
3.4 Factory Mode
3.5 DVD, DTV I-DRIVE input
3.6 Original Button Usage
3.7 Rear Camera
3.8 Rear Parking Guidelines
3.9 OSD
4. Trouble Shooting
4
5
6
7
9
10
11
13
14
15
16
19
21
22
24
25
27
1. Specifications
1.1 Main Specifications
4
1. Compatibility
Most of brand-new cars coming with CIC Navigation
Computer System including BMW 5 series
2. Product composition
Multimedia Interface * 1ea
3. MULTIMEDIA INTERFACE input spec.
3 * A/V input (external video input)
1 * CVBS input (rear camera source input)
1 * RGB input (navigation system & HDMI)
1 * LCD input (car system input)
4. MULTIMEDIA INTERFACE output spec.
1 * LCD output
5. POWER spec.
input power : 8VDC ~ 18VDC
consumption power : 5 WATT
6. Switch input mode
- Input video skip function : able to select whether to
use the respective input video sources or not via DIP
switch.
- Able to change input modes via the remote control.
- Able to detect rear camera via CAN or rear lamp
cable.
- Able to change modes via an OEM Button
1. Specifications
1.2 Features
5
Able to control NAVI, DVD, DTV function via Multimedia
Touch GUI
Able to adjust external image (DVD, NAVI) display on
screen
Improved Screen Display (user-oriented interface)
Mode change through original button
Provide power cables to connect with rear camera
Dynamic PAS(Parking assistance system)
1. Specifications
1.3 System Diagram
6
DISPLAY
A/V 1
NAVIGATION Input
(Analog RGB)
CVBS
(Rear camera)
Car Screen Input
(CAR MAIN BOARD)
A/V 2
A/V 3
VIDEO
CIRCUIT
VIDEO MUX
MCU
Power Input
(+8VDC ~ +18VDC)
POWER
CIRCUIT
Dip S/W
A/V OUT HEADREST
MONITOR
Remote control Switch for source toggle
OEM Button (Can Signal)
Car Installation
OEM LCD
Rear Camera Power
(+9VDC)
HDMI Input
(RGB-IN2)
1. Specifications
1.4 Components
A/V cable * 1EA
Mode cable * 1EA
IR cable * 1EA
R-CAM POWER cable * 1EA
(HARETC0002)
(HAVCAB0002)
Remote control * 1ea
(REMOTE0001)
(HARETC0001)
(HIRCAB0002)
TOUCH OUT cable * 1ea
(HTOUCH0004)
TOUCH IN cable * 1ea
(HTOUCH0009)
RGB cable * 1ea
(HRGBCA0013)
7
LCD cable * 1ea
(HLCDCA0005)
Modified POWER cable * 1EA
(HPOWER0012) , (HPOWER0021)
BMW09CIC
1. Specifications
1.4 Components
8
6.5” Touch Panel
(TOUPAN0003)
8.8” Touch Panel
(TOULCD0011)
1. Specifications
1.5 Exterior
① ⑥ ⑦ ⑧
⑨ ⑩ ⑪ ⑫
① MODE
② IR
③ POWER
④ TOUCH OUT
⑤ REAR
⑥ RGB-IN HDMI
⑦ RGB-IN NAVI
⑧ AV IN/OUT
⑨ LCD-OUT
⑪ T/S-IN
Dimension
Width 150.4mm
Length 99.4mm
Height 2.3.2mm
⑬
⑩ LCD-IN
② ③ ④ ⑤
⑫ TEST
⑬ LED
9
⑭
⑬ DIP S/W
BMW09CIC
2. Installation
2.1 Installation Diagram
10
Offered
LCD Cable
Original
Monitor
AV1
AV2
AV3
REAR C
Audio L
Audio R
AV/OUT Video
REAR (12V OUT)
GND
B DATA (blue)
SYNC
GND
IR-DTV
NAVI-VS
IR-NAVI
IR-DVD
R DATA (red)
G DATA (green)
Original LCD Cable
GND
ACC
CAN
CAN
Noise filter
Box
Connecting the original POWER & CAN cable to this part.
Connecting this to the spot which the original POWER & CAN cable was connected.
Control Box
BMW09CIC
Table des matières
