Techage POE NVR Manuel utilisateur
POE NVR
User Manual
www.techage.com
Security Expert for Your Home and Business
XMEye Pro App
1. NVR Installation
1.1 Hard Disk Installation
1.2 Boot & Preview
2. Function Setting
2.1 Login System
2.2 HDD Setup
2.3 General
2.4 Record Setup
2.5 Video Playback
2.6 Video Backup
2.7 Snapshot Configuration
2.8 Network Setup
2.9 Check Nat Status
2.10 Email Setup
2.11 User Management
2.12 Audio Setting
2.13 Alarm
2.13.1 Intelligent Alert Setting
2.13.2 Advanced Setting of Human Detection/Face Detection
2.13.3 Advanced Settings of Vehicle Detection
2.13.4 Advanced Settings of Safe Zone & Line Cross Alarm
2.13.5 Abnormality Settings
2.13.6 Traditional Alarm Setting
5.1 Remote View via Browser
5.2 Remote View via PC Software
5.3 Remote View via Phone App
5. Remote View
4. Add IP Camera
3. Digital Channels Setup
04
04
04
05
05
05
06
07
08
09
10
11
12
12
15
16
16
17
18
20
20
22
23
26
27
28
25
25
24
Table of Contents
Thanks for purchasing our PoE Network Video Recorder Surveillance products. This user
manual is for 4CH/8CH/16CH PoE NVR and PoE cameras system. The firmware and software
for the cameras and NVRs will be updated for better user experience. Please write to us or
visit the store to get the latest user manual.
PWR: It will be on when the NVR is plugged in power adapter (DC 48V~52V).
Directions: Choose different options on NVR, left or right, up or down.
USB: For connecting USB mouse to control NVR or USB disk to backup video.
IR: To receive infrared remote control signal.
QUAD: Switch the video display on monitor to 1/4/8/16 channels.
ESC: Leave the current option/window, cancel or back to previous option.
MENU: Enter main menu directly.
ENTER: Enter the options.
QUAD
IR
ESC MENU ENTER
USB
Front of the NVR
NVR Overview
Preface
01
OFFON
DC IN AUDIO OUT VGA HD-PORT
UP LINK
POE8 POE7 POE6 POE5
POE4 POE3 POE2 POE1 USB
Back of the NVR
Switch: Turn on/off NVR.
DC IN: For power supply DC 48~52V, the size of the DC plug is 5.5*2.1mm.
PoE 1-8: Ethernet ports for connecting the PoE Cameras.
UP LINK: Ethernet port for connecting to the router.
AUDIO OUT: For connecting speakers to play the recorded audio.
VGA: For connecting the monitor or display with VGA cable.
HD-PORT: For connecting the monitor or display with HDMI cable.
USB: For connecting USB mouse to control NVR or USB disk to backup video.
Wiring and Connection Diagram
OFFON
DC IN AUDIO OUT VGA HD Port
UP LINK
POE1 POE2 POE3 POE4
POE5 POE6 POE7 POE8 USB
Router Display Device for Remote View
PoE IP Camera
Display Device(TV/Monitor with VGA/HD Port)Power Supply
HDMI CableVGA Cable
PoE NVR
Mouse
02
After the wiring and connection as above, the live images should be shown on the
monitor or display. Then you can install the cameras and do the wiring.
When you install the cameras, please make sure to avoid the inaccurate ways of installations.
Wrong Way: The wall will reflect the light from the IR lights to the lens at night if the
camera lens are installed too close to the wall.
Right Way: Adjust the directions of the camera lens and make sure the lens of the camera
are away from the wall.
Wrong Way: There are objects too close to the camera lens. The object will reflect light
from the IR light to the lens.
Right Way: Move the objects away from the camera lens or change the camera's installation
position.
Wrong Way: The wire cables of the camera, like power cable or Ethernet cable are too close
to the camera lens. The cables will reflect light from IR light to the lens.
Right Way: Move the power cable or Ethernet cable away from the camera lens and fix it
on the back of the camera.
Close Wire Cable Reflects
Close Object Reflects
Wrong Viewing Angles
Cameras Installations
03
1NVR Installation
1.1 Hard Disk Installation
Please install the hard disk first. If not, the video recorder can only monitor normally, but
cannot record or playback.
Notice: Please choose a specialized monitoring hard drive disk in order to record
for a longer time. The video recorder supports 3.5" or 2.5" SATA hard disk.
Warning: please make sure the power is off before installation.
1 2
3 4
Remove the case Plug in SATA cable
Screw HDD to the bottom Install the case back
1.2 Boot & Preview
Make sure the power supply matches the requirements of the hard disk video recorder.
After connecting the power, the indicator on the front of the NVR will light on and you
04
will hear a buzzer sound, then the display will boot up and the device will access to the
preview image. After the recovery of the non-normal power failure, the device will
automatically return to the state it was in before the power outage.
2Function Setting
2.1 Login System
After the normal boot, you have to log in first and the system will provide the corresponding
function according to the user's rights.
Right click the mouse → 【Main Menu】
2.2 HDD Setup
Right click the mouse→【Main Menu】→【Advanced】→【HDD Info】
User name: admin (default)
Password: Just leave it blank as default.
05
Choosing the Hard Disk, clicking Format Storage, starting to format the HDD.
Notice: Please confirm the hard disk is connected. The hard disk should be formatted
before first use, so that it can record properly. It will automatically overwrite previous
videos when the storage of hard disk is full if you set overwrite.
2.3 General
Right click the mouse→【Main Menu】→【System】→【General】
[Language] You can set the system language to the native language.
[Storage Full]
Choose Overwrite: Keep recording video and automatically overwrite the former video
while the storage of HDD is full.
Choose Stop: Stop recording video while the storage of HDD is full.
06
[Auto Logout] You can set up a 0-60 min auto standby. 0 min means you haven't set up the
standby time.
[Startup Wizard] Tick it to get startup wizard when reboot the system (untick it as default).
2.4 Record Setup
In the Record Configuration, you can set up the record mode for each channel to save space
of the HDD and only record the important videos.
Right click the mouse→【Main Menu】→【Record Conf.】
[Channel] The channel which you want to do settings of record configuration.
[Length] The standard length of each video segment.
[Mode] The way you want to record videos.
Schedule: The selected channel will only record during the chosen time period.
Manual: The selected channel will record 24/7.
Stop: The selected channel will not record any video.
Regular: The system will keep recording during the chosen time period.
Detect: The system will record a video segment when the camera detects
movements during the chosen time period.
Alarm: The system will record a video segment when the camera alarms
during the chosen time period.
07
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Techage DVR
