Teasi CORE Manuel utilisateur

User Manual

English

This manual covers all the details and explanations of the TEASI CORE.

VERSION 13-20-04-2017_F01

Table of Contents

The use and operation of navigation systems.................................................................................. 3

Teasi Core ......................................................................................................................................... 3

1. Getting to know your Core ....................................................................................................... 4

2. Charging the Teasi Core ............................................................................................................ 5

3. Speed/Cadence Sensor ............................................................................................................. 5

4. Using Bluetooth Sensors........................................................................................................... 5

4.1 Speed/Cadence Sensor........................................................................................................ 5

5. Installation of Teasi Core on your bicycle................................................................................. 6

6. Installation of speed/cadence sensor....................................................................................... 6

7. Teasi Core has 2 working modes .............................................................................................. 8

7.1 App working mode .............................................................................................................. 8

7.1.1 Connect to Tahuna.......................................................................................................... 8

7.1.2 Speedometer Display of Teasi Core .............................................................................. 10

7.1.3 Page Display of Teasi Core ............................................................................................ 11

7.2 Bike Computer Mode ........................................................................................................ 12

7.2.1 Manual pairing method for sensors and Teasi Core..................................................... 13

7.2.2 Start and stop of riding ................................................................................................. 14

7.3 Settings menu.................................................................................................................... 14

7.3.1 Basic settings................................................................................................................. 14

7.3.2 Wheel size setting ......................................................................................................... 15

8. Connect the Teasi Core to the Tahuna App............................................................................ 16

9. Connection.............................................................................................................................. 20

10. Computer layout and selection change.................................................................................. 23

11. Navigation (turn instructions to Teasi Core)........................................................................... 24

12. Troubleshooting...................................................................................................................... 25

13. Specifications .......................................................................................................................... 25

14. Appendix ................................................................................................................................. 26

14.1 Data Fields..................................................................................................................... 26

User information/Contact .............................................................................................................. 27

Declaration of Conformity .............................................................................................................. 27

Guarantee ....................................................................................................................................... 27

The use and operation of navigation systems

Attention! Don’t operate with the device while driving. Even the smallest and shortest distractions

from road or traffic for you and other road users - even at slow speeds –may have devastating

consequences.

Type in the destination before starting your journey and start the navigation system before you

start driving.

If you have to change the route or the settings while driving, you should better stop for it.

Teasi Core

Teasi Core is an intelligent bike computer which can be connected via Bluetooth® with your

smartphone (free TAHUNA App for Android and iOS) or external fitness sensors and displays basic

values as well as navigation instructions, training data and incoming calls.

This product is provided with a built-in battery that can be charged with a charger above DC 5V, 500

mA or PC USB interface when the battery is too low to supply power to Teasi Core.

This product is provided with a monochrome display screen, its backlight can be turned on

manually at night for better vision, and turned off at day to save power. You can also set backlight

into auto on/off mode in the settings menu.

Delivery contents:

-Device Teasi Core

-Speed- & cadence sensor

-4 nylon straps and 1 rubber band for the sensor

-Wheel and pedal magnet

-HR mounting bracket with 2 cable ties and adhesive label

-USB cable

-Quick Start Guide

-Note for connecting Teasi Core to Tahuna app

1. Getting to know your Core

1. USB charging interface/USB rubber

stopper

2. Long press: power on/off

short press: backlight on/off

3. Reset

4. Buzzer

5. Auto backlight on/off induction window

6. Mounting for HR bracket

A/B/C shown in the figure above are only the functional buttons of this product, please see

the table below for their specific functions:

Buttons

Normal mode

Setting mode

Short press: change display mode

Long press 1 sec: go into settings

picture

Short press: change option,

backward/left direction

Long press 1 sec: exit the settings picture

Long press 1 sec: change to App

working mode

Long press 2 sec: go into pair

sensor mode

Short press: Change digit/confirm

(Yes/No)

Short press: start/pause recording

Long press: stop recording

Short press: select next digit or

option/right direction

Buttons

Pairing sensors mode

Connect with APP mode

Long press 1 sec: exit pair sensor

picture

Short press: exit smartphone search

Short press: start search

sensors/search next

sensor/exit if both

sensors are connected

Short press: start/pause recording

Long press 1 sec: stop recording

2. Charging the Teasi Core

1. Pull up the USB rubber stopper from the USB charging interface (1).

2. Plug the small end of the USB cable in the USB charging interface.

3. Connect the large end of the USB cable to a 5V AC adaptor or a USB port on a computer.

4. Charge the Teasi Core for the first time completely, around 4 hours. The average charging

time is 1.5 hours. When the battery is completely discharged, the device may only turn on

after the battery has been charged for some time. When the device is turned off, a progress

bar on the display indicates the charging progress during charging.

3. Speed/Cadence Sensor

Wireless speed/cadence sensor Wheel magnet Pedal magnet

Bluetooth name: Teasi SPC

4. Using Bluetooth Sensors

4.1 Speed/Cadence Sensor

a) There is a CR2032 button cell inside the product to provide power and its service life is 4

months in general. Teasi Core or Tahuna will fail to detect sensors when sensor cell is

dead or sensor is damaged. Sensor cell can be replaced according to the figure below.

Please note: when you use this product for the first time, please remove the battery

hatch to remove the insulation film.

b) This product can be connected to any equipment conforming to BLE 4.0 standard protocol

and transmit data to it.

c) This product will get into sleep mode after wheels stop spinning for 5 min in order to save

power; it will also get into sleep mode when Tahuna or Teasi Core disconnects from

sensor. When it is used again, bike wheels shall be made spun to activate sensor, so that

the product can be searched by Tahuna or Teasi Core.

5. Installation of Teasi Core on your bicycle

Fix the Teasi Core on the bracket as shown in the figure below.

6. Installation of speed/cadence sensor

Install pedals magnet (RPM) and wheel magnet (speed) in corresponding positions as shown in

the figure below:

Tear the 3M adhesive on the back of pedal magnet off and stick pedals magnet inside the

pedal connecting arm, and then tie up the 2 nylon straps to fix it, and cut unnecessary part

down.

Install the wheel magnet on wheel spoke and tighten it, so as to ensure that it will not slide

when the wheel is spinning at a high speed.

Fix speed/cadence sensor on corresponding position of bike as shown in the figure, and then

tighten it with 2 nylon straps.

Then, fix it again with a rubber band.

Please note: the centers of pedal magnet and wheel magnet shall be aligned with corresponding

induction part of sensor and shall not be deviated from it too far; the magnets shall not be more

than 2 cm from the induction part, since distance larger than 2 cm will make it fail to receive the

wheel spinning signal. Screws can be loosened with screwdriver to adjust the distance between the

extendible arm of inductor and spoke magnet.

7. Teasi Core has 2 working modes

a) App working mode:

Teasi Core is only a display equipment that needs to pair and connect to app, and all its

data is from app push; in this mode, speed/cadence sensor and heart rate monitor shall

pair with Teasi Core and connect to it.

b) Bike computer working mode:

Teasi Core is only a bike computer that is not connected to app; in this mode, speed/

cadence sensor and heart rate monitor shall pair with Teasi Core and connect to it.

7.1 App working mode

7.1.1 Connect to Tahuna

You can scan the QR code displayed on this equipment when it is started first time or the QR

code printed on the package to enter the website, and download and install the Tahuna app.

This product will search to connect with Tahuna automatically after it is started, as shown in

the left of the following figure. If you do not need to connect to Tahuna or Tahuna has

stopped working, you can press the far left button to EXIT:

Teasi Core starts to connect to Tahuna

When the app detects a new version of Teasi Core to update to, there will be a dialogue box

of update prompt given on the app. You can click the update button on the app to make

Teasi Core update automatically. The following update progress bar will be shown.

Notice:

Please make sure your phone and Teasi Core have enough power before updating, keep

Bluetooth connection smooth in updating process, and do not take your phone away from

Teasi Core. If update does not progress for a long time or power fails, or Bluetooth signal is

lost in updating process, Teasi Core will return to its old version and will update again when it

is connected to the app next time.

You need to turn the Bluetooth of your smartphone and the connect switch of Tahuna on, so

that Tahuna can seek to connect with Teasi Core. The main interface will be entered after the

successful connection and the successful connection symbol as shown in the figure below will

be shown; at the same time, you need to connect Tahuna with speed/cadence sensor and

heart rate sensor.

When all connections are finished, Teasi Core can start to work.

Successful connection of Teasi Core and Tahuna

Please note: You need to make sure that Teasi Core or sensors are not connected to other

Bluetooth equipment and can be effectively connected to Tahuna.

7.1.2 Speedometer Display of Teasi Core

Speedometer

Successful connection to Tahuna

Smartphone battery

Smartphone GPS on

Current time

Equipment battery

Maximum speed

Current speed

Accumulative mileage

After the equipment is connected to Tahuna, the 2

data types can be changed on the app in the

speedometer view.

Table des matières

Autres manuels Teasi Accessoires pour vélos

Teasi

Teasi NAV-BIKTS Manuel utilisateur

Manuels Accessoires pour vélos populaires d'autres marques

Sigma

Sigma BC 16.16 Manuel utilisateur

Playcore

Playcore Dero Setbacks Manuel utilisateur

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manuel utilisateur

Cateye

Cateye RAPID X2 Manuel utilisateur

buratti meccanica

buratti meccanica Clorofilla Trail Manuel utilisateur

Shimano

Shimano SG-8R20 Mode d'emploi

BOB

BOB YAK Manuel utilisateur

APLIC

APLIC 303303/20190717TW012 Manuel utilisateur

SRAM

SRAM AXS BlipBox Manuel utilisateur

Garmin

Garmin EDGE 500 Manuel utilisateur

Shimano

Shimano FD-RX810 Manuel utilisateur

Cateye

Cateye V2C - Manuel d'instructions

KMART

KMART 43115907 Manuel utilisateur

SIGMA SPORT

SIGMA SPORT Buster 2000 Manuel utilisateur

NVO Components

NVO Components STEM Manuel utilisateur

DAXYS

DAXYS BP188 Manuel utilisateur

XLC

XLC BV-W17 Manuel utilisateur

Deda Elementi

Deda Elementi SUPERBOX Manuel utilisateur