TE Connectivity SDE-SA Manuel utilisateur

Instruction Sheet

1 of 6

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

408-35306

30 AUG 2022 Rev A

PROPER USE GUIDELINES

Cumulative trauma disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional

use and low-volume applications. A wide selection of powered application equipment is available for extended-use production operations.

The SDE-SA hand tool is a commercial-grade tool. Product crimped with this tool meets the wire barrel crimp height requirement for hand

tools in the appropriate 114 application specification, but might not comply with other feature parameters of the specification.

Figure 1: SDE-SA Commercial Hand Tool Assembly 2405500-1 with Die Assembly 2405500-2

Die set 2405500-2

Moving jaw

Upper hex die

Ratchet adjustment wheel

Lower hex die

Die-retaining screws

Stationary jaw

Handle

SDE-SA Commercial Hand Tool Assembly

PN 2405500-1 with

Die Assembly PN 2405500-2

Rev A

2 of 6

1. INTRODUCTION

SDE-SA Commercial Hand Tool Assembly 2389146-1 for the Contact Kit, Ferrule, RG58; RTK031; RG174 is

the tool and die set shown in Figure 1. The tool consists of the SDE Crimp Hand Tool Frame 2362810-1

(instruction sheet 408-35143) and the die assembly listed in Figure 1. This tool is used to crimp the terminal

part numbers listed in Table 1.

Table 1: Crimping specifications

Crimp tooling

Contact kit

Cable type

Cable

Strip length mm

SDE-SA tool

Die assembly only

2405500-1

2405500-2

829922

1337552

RG58

Inner conductor

2.5 +/-.0.2

1488171

1488175

RTK031

Dielectric

4.2 +0.3/-0.2

1488147

1488155

RG174

Braid

9.7 +0.3/-0.2

NOTE

Dimensions in this instruction sheet are in millimeters with [inches in brackets]. Figures are for reference only and are not

drawn to scale.

Read these instructions thoroughly before crimping connectors.

2. DESCRIPTION

The tool frame features two jaws, a handle, a ratchet adjustment wheel, and an emergency ratchet release.

The die set consists of a crimper (upper die) and an anvil (lower die). The tool frame holds a die assembly with

three crimping chambers (see Figure 1). Two SCR Mach M4x14.0 die-retaining screws are used to secure the

dies in the tool frame.

The tool features a ratchet and an adjustment wheel with a range of settings. The ratchet ensures that the tool

has completed the cycle and does not release until the handles have been fully closed, unless the emergency

ratchet release is rotated to manually release the ratchet. The adjustment wheel controls the amount of handle

pressure exerted on the dies during the crimping procedure.

CAUTION

The dies bottom before the ratchet releases. This feature ensures maximum tensile performance of the crimp. Do not re-

adjust the ratchet unless you have verified that the crimp height is incorrect (see section 7, ADJUSTING THE RATCHET).

3. INSTALLING THE DIE SET

1. Open the tool handles.

2. Remove the two die-retaining screws from the tool jaws (see Figure 1).

3. Insert the lower hex die in the moving jaw of the tool frame with the chamfered side and the marked

surface facing outward.

4. Insert one die-retaining screw through the jaw and through the lower hex die. Tighten the screw just

enough to hold the die in place. Do not tighten the screw completely.

5. Insert the upper hex die in the stationary jaw of the tool frame with the chamfered side and the marked

surface facing outward.

6. Insert the other die-retaining screw through the jaw and through the upper hex die. Tighten the screw

just enough to hold the die in place. Do not tighten the screw completely.

7. Carefully close the tool handles, making sure the lower and upper dies align properly. Continue closing

the tool handles until the ratchet in the tool frame has engaged sufficiently to hold the dies in place.

8. Tighten both die-retaining screws.

Rev A

3 of 6

4. REMOVING THE DIE SET

1. Close the tool handles until the ratchet releases.

2. Remove the two die-retaining screws.

3. Slide the dies out of the tool jaws.

NOTE

The ratchet release has detents with audible clicks as the handles are closed. The ratchet releases on the sixth click.

5. CRIMPING

NOTE

The tool is provided with a crimp adjustment feature. Initially, the crimp height should be verified as specified in Figure 3. Refer

to section 6, INSPECTING THE CRIMP HEIGHT, and section 7, ADJUSTING THE RATCHET, to verify crimp height before

using the tool to crimp contacts and wire sizes.

1. Refer to Table 1 and select wire of the specified size and insulation diameter.

2. Strip the wire to the length indicated. Do not nick or cut wire strands.

3. Select an applicable ferrule and identify the appropriate crimp section according to the wire size

markings on the tool.

4. Position the strands of the wire braid.

5. Slip the ferrule over the wire braid until it stubs with the shoulder of the rear shell subassembly or of the

front shell subassembly. This is the ferrule’s end position (Figure 2).

NOTE

Ensure that the strands of the wire braid do not protrude over the knurling. The strands must not be visible after positioning

the ferrule. This prevents the strands from becoming stuck between the ferrule and the shoulder of the rear or front shell

subassemblies.

6. While holding the wire in place, fully cycle the tool until the ratchet releases and allows the handle to

open.

Figure 2: Positioning the ferrule

End position

No wire strands visible

Crimped ferrule

Rev A

4 of 6

6. INSPECTING THE CRIMP HEIGHT

Crimp height inspection is performed using a micrometer with a modified anvil, commonly referred to as a

crimp-height comparator. TE Connectivity does not manufacture or market crimp height comparators. Detailed

information on obtaining and using crimp-height comparators can be found in instruction sheet 408-7424.

1. Refer to Table 1 and select a wire (maximum size) for each crimp section listed.

2. Refer to section 5, CRIMPING, and crimp the contacts accordingly.

3. Using a crimp height comparator, measure the wire barrel crimp height listed in Table 2.

If the crimp height conforms to that shown in the table, the tool is considered dimensionally correct.

If not, adjust the tool. Refer to section 7, ADJUSTING THE RATCHET.

CAUTION

Do not use damaged product. If a damaged contact is evident, replace it. Do not re-terminate contacts.

Figure 3: Crimp height

Modified anvil

Position point on center of wire barrel opposite seam

Crimp height (see Table 2)

Table 2: Crimp height specifications

Die assembly

Cable type

Hex mm [in.]

2405500-2

RG58

5.50±0.05 [.217±.002]

RTK031

4.10±0.05 [.161±.002]

RG174

3.25±0.05 [.128±.002]

Rev A

5 of 6

7. ADJUSTING THE RATCHET

The ratchet is preset prior to shipment, but it is important to verify the crimp height using a micrometer or

caliper. Use and wear can cause the tool to go out of adjustment. Inspect the crimp height and adjust the

ratchet, if necessary, on a regular basis.

To adjust the ratchet, complete the following steps.

1. Remove the ratchet wheel lock screw (Figure 4).

2. Rotate the adjustment wheel.

If the crimp height is larger than recommended, rotate the adjustment wheel counter-clockwise ()

to a higher setting.

If the crimp height is smaller than recommended, rotate the adjustment wheel clockwise (–) to a

lower setting.

3. Reinstall the lock screw.

4. Make a sample crimp and measure the crimp height.

5. Repeat as required.

If the crimp height cannot be made to conform to the recommended crimp height, replace the tool or die

set. See section 9, REPLACEMENT AND REPAIR.

Figure 4: Ratchet adjustment

Lock screw

Ratchet adjustment wheel

Rev A

6 of 6

8. MAINTENANCE AND INSPECTION

8.1. Maintenance

Remove dust, moisture, and other contaminants with a clean, soft brush or soft, lint-free cloth. Do not

use objects that could damage the dies or tool.

When the tool is not in use, keep the handles closed to prevent objects from becoming lodged in the

dies.

Remove all lubrication and accumulated film by immersing the dies in a suitable commercial degreaser.

Store the tool in a clean, dry area.

8.2. Visual inspection

Inspect the tool and dies on a regular basis to ensure that they are not worn or damaged.

Make sure that the die retaining screws are properly secured.

Inspect the crimping chambers of the die assembly for flattened, chipped, worn, or broken areas.

If damage or abnormal wear is evident, replace the tool or dies. Refer to section 9, REPLACEMENT

AND REPAIR.

9. REPLACEMENT AND REPAIR

If the dies are damaged or worn excessively, they must be replaced. Order replacement dies through your TE

representative. You can also order parts by any of the following methods:

Go to TE.com and click the Shop TE link at the top of the page.

Call 800-522-6752.

Write to:

CUSTOMER SERVICE (038-035)

TE CONNECTIVITY CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

For customer repair services, call 800-522-6752.

10. REVISION SUMMARY

Revisions to this instruction sheet include:

Initial release

Autres manuels pour SDE-SA

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TE Connectivity Outils

TE Connectivity

TE Connectivity CERTI-CRIMP II Guide de référence

TE Connectivity

TE Connectivity CXP 2018681-1 Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 6-1579014-1 Manuel utilisateur

TE Connectivity

TE Connectivity TERMI-POINT 59865-1 Guide de référence

TE Connectivity

TE Connectivity 354711-1 Manuel utilisateur

TE Connectivity

TE Connectivity 2255143-1 Manuel utilisateur

TE Connectivity

TE Connectivity 734185-1 Manuel utilisateur

TE Connectivity

TE Connectivity CERTI- LOK Hand Tool Frame Assembly 169400 Manuel utilisateur

TE Connectivity

TE Connectivity 58372- 1 Manuel utilisateur

TE Connectivity

TE Connectivity 2215038-1 Manuel utilisateur

TE Connectivity

TE Connectivity HT11K Manuel utilisateur

TE Connectivity

TE Connectivity 2255140-1 Manuel utilisateur

TE Connectivity

TE Connectivity 768338-2 Manuel utilisateur

TE Connectivity

TE Connectivity 90331- 1 Manuel utilisateur

TE Connectivity

TE Connectivity SDE-SA Manuel utilisateur

TE Connectivity

TE Connectivity 2379255-1 Manuel utilisateur

TE Connectivity

TE Connectivity 58024-1 Manuel utilisateur

TE Connectivity

TE Connectivity OCEAN 2.0 Manuel utilisateur

TE Connectivity

TE Connectivity Ocean 1.0 Manuel utilisateur

TE Connectivity

TE Connectivity 2430769-1 Manuel utilisateur

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 1725062-1 Manuel utilisateur

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser