TE Connectivity Type N Manuel utilisateur

Mounting Nut

Lockwasher

Gasket

Housing

Dielectric

Center Contact

O-Ring Rear Housing

TE CONNECTIVITY

PART NUMBER PREVIOUS PART

NUMBER DESCRIPTION CABLE TYPE

1057160-1 3004-7941-01 Type N Bulkhead Feedthrough Cable Jack - .141 Semi-Rigid Coaxial Cable

- .141 Semi-Rigid Microporous Cable

1057159-1 3004-7941-00

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

1of 2

Instruction Sheet

TOOLING ASSISTANCE CENTER

1-800-722-1111



PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com LOC B

408-4911

Type N 

Bulkhead Feedthrough 

Cable Jack Connectors 03 NOV 11 Rev C

Figure 1

1. INTRODUCTION

These instructions cover the application of the Type N

Bulkhead Feedthrough Cable Jack Connectors listed

in the table in Figure 1. These connectors are used in

direct solder attachment type applications.

NOTE

Dimensions in these instructions are in metric units

[with U.S. customary units in brackets], unless

otherwise indicated. Figures are for identification

only and are not drawn to scale.

The table in Figure 2 indicates the tooling required for

the application of these connectors. The TE part

numbers are listed, along with the previous part

numbers, and the tooling description.

TE PART

NUMBER PREVIOUS PART

NUMBER DESCRIPTION

1055439-1 2098-5206-54

(T-4567) Cable Fixture

Subassembly

1055440-1 2098-5207-54

(T-4700-1 Clamp Insert Assembly

1055472-1 2098-5277-10

(T-4561) Center Contact Holder

91362-1 - - Solder Gage

1055471-1 2098-5276-02

(T-4572) Locator Tool

Figure 2

Reasons for revision can be found in Section 3,

REVISION SUMMARY.

2. ASSEMBLY

2.1. Cable Preparation (See Figure 3)

1. Insert the squared end of the cable into the fixture

base hole pattern #2.

2. Place the saw in the saw slot and cut through the

outer conductor and into the dielectric while rotating

the cable.

DANGER

STOP

To avoid personal injury, always use caution and

followall localpractices whenusing acutting blade.



3. Remove the cable from the fixture and finish

cutting the cable with a cutting blade.

4. Bare the inner conductor by prying the outer

conductor and dielectric from the cable.

2.2. Soldering the Center Contact to the Cable Inner

Conductor (See Figure 4)

DANGER

STOP

To avoid personal injury, always use caution and

follow all local practices when using soldering

equipment.



1. Tin the inner conductor of the cable.

2. Place the solder gage on the inner conductor

flush with end of the outer conductor.

3. Place the center contact in the holder, heat the

center contact and push it over the inner conductor

of the cable to rest firmly against the solder gage.

4. Remove solder gage and excess solder.

NOTE

408-4911

2of 2

Rev C

DO NOT use flux or solvent in the cable dielectric

area of micro-porous cable.



2.3. Soldering Cable Sub-Assembly to Rear Housing

1. Place the rear housing on the end of the cable

sub-assembly.

2. Place loose assembly in fixture base as shown in

Figure 5

a. Nest the center contact in the locator tool.

b. Tighten the clamp screw to secure the cable.

c. Tighten the locator tool to seat the cable firmly.

3. Slide the rear housing over the locator tool.

4. Maintain the position of the rear housing firmly

against the locator tool.

5. Solder.

NOTE

Keepthefixture clampedverticallyina vicetokeep

the rear housing seated against the locator tool.



2.4. Assembling the Connector

1. Insert the dielectric bushing (counterbore toward

the front) over the center contact into the housing.

2. Assemble the O-ring onto the rear housing as

shown in Figure 6.

3. Secure the housing to the threads of the rear

housing sub-assembly.

4. Tighten to a torque of 2.82 to 3.39 N•m 

[25 to 30 in-lb].

5. These procedures should yield the tolerances in

Figure 7.

3. REVISION SUMMARY

Since the previous version of this document, the

following changes were made:

•Corrected wording of heading in Paragraph 2.2.

•Updated document to corporate requirements.

Fixture Base Hole Pattern #2 Outer Conductor

Cable Dielectric

2.79 ±0.254]

[.110 ±.010]

90°

Figure 3

Fixture Base

Center Contact Center

Contact

Heat Here Solder Gage

Cable

0.381 ±0.025

[.015 ±.001]

HolderHolder

Figure 4

Fixture Base Housing

Locator

Tool Clamp

Insert

Cable

Sub-Assembly

Clamp

Assembly

Solder Here

with 60/40

Solder

Figure 5

Center Contact Dielectric

O-Ring

Rear Housing

Figure 6

Reference Plane 5.26 Max

[.207 Max]

Figure 7

Ce manuel convient aux modèles suivants

Autres manuels TE Connectivity Câbles et connecteurs

TE Connectivity

TE Connectivity 747564-9 Manuel utilisateur

TE Connectivity

TE Connectivity AMP-HDI Manuel utilisateur

TE Connectivity

TE Connectivity AMPOWER 68361-1 Manuel utilisateur

TE Connectivity

TE Connectivity HVA630-2phm Manuel utilisateur

TE Connectivity

TE Connectivity D5000-S Manuel utilisateur

TE Connectivity

TE Connectivity M12 Guide de l'utilisateur

TE Connectivity

TE Connectivity D369 Series Manuel utilisateur

TE Connectivity

TE Connectivity 025/250 Manuel utilisateur

TE Connectivity

TE Connectivity RAYCHEM D-436 Series Guide de référence

TE Connectivity

TE Connectivity 55PC1122-16-9/96-9 Manuel utilisateur

TE Connectivity

TE Connectivity TNC COAXICON Series Manuel utilisateur

TE Connectivity

TE Connectivity Quadrax DSub Guide de l'utilisateur

TE Connectivity

TE Connectivity AMP-LATCH Guide de l'utilisateur

TE Connectivity

TE Connectivity AMP NETCONNECT 1499119-1 Manuel utilisateur

TE Connectivity

TE Connectivity QSFP-DD Guide de l'utilisateur

TE Connectivity

TE Connectivity SGI 1.25 Guide de l'utilisateur

TE Connectivity

TE Connectivity Raychem LJSM Series Manuel utilisateur

TE Connectivity

TE Connectivity HV-CP Manuel utilisateur

TE Connectivity

TE Connectivity DYNAMIC 5000 Series Manuel utilisateur

TE Connectivity

TE Connectivity DRC16 Manuel utilisateur

TE Connectivity

TE Connectivity Miniature AMP-IN Guide de l'utilisateur

TE Connectivity

TE Connectivity EP-II Manuel utilisateur

TE Connectivity

TE Connectivity VAL-U-LOK 3-1586040-6 Manuel utilisateur

TE Connectivity

TE Connectivity CCS1 Manuel utilisateur

Manuels Câbles et connecteurs populaires d'autres marques

Philips

Philips SWA6310 Manuel utilisateur

StarTech.com

StarTech.com CRJ4550PK Manuel utilisateur

Nohau

Nohau EMUL-IP2K-PC Manuel utilisateur

Foxun

Foxun SX-SP144E-HD4K2K Manuel utilisateur

Philips

Philips SWA3305W Manuel utilisateur

opticis

opticis Stretch DVIM1-1P0x Manuel utilisateur

Volkswagen

Volkswagen VAS 6558A Manuel utilisateur

NEXIBO

NEXIBO N-13 Manuel utilisateur

CYP

CYP PU-1H3HBTL Manuel utilisateur

Allen-Bradley

Allen-Bradley 1784-u2dhp Manuel utilisateur

Global Caché

Global Caché Flex Link Blaster Manuel utilisateur

Hauppauge

Hauppauge USB-Live2 Manuel utilisateur

Fenix

Fenix MPSV 15 Manuel utilisateur

BEGA

BEGA 71 085 Manuel utilisateur

Tesla

Tesla HPWC Manuel utilisateur

GAMERON

GAMERON LUXURY TV CABLE Manuel utilisateur

molex

molex Milli-Grid Dual row 87568 Series Manuel utilisateur

Burndy

Burndy Continental Industries thermOweld CRE-7 Manuel utilisateur