TDK-Lambda PHV Series Guide de l'utilisateur

IEEE DIGITAL INTERFACE SETUP MANUAL FOR

PHV Series High Voltage

POWER SUPPLY

Document: 83550130 Rev A

TDK-LAMBDA AMERICAS

405 Essex Road, Neptune, NJ 07753

Tel: (732) 922-9300

Fax: (732) 922-9334

Web: www.us.tdk-lambda.com/hp

THIS PAGE LEFT INTENTIONALLY BLANK

83550130 Revision A

Table of Contents

1. Overview...................................................................................................................................3

1.1. Scope........................................................................................................................................3

1.2. ADDR LED................................................................................................................................3

1.3. Service Request (SRQ) LED.....................................................................................................3

2. Interface setup information........................................................................................................5

2.1. GPIB primary address (PA).......................................................................................................5

2.2. Other DIP switch settings..........................................................................................................5

83550130 Revision A

THIS PAGE LEFT INTENTIONALLY BLANK

83550130 Revision A

1. Overview

1.1. Scope

This manual applies to PHV series power supplies equipped with the IEEE digital interface

option. The manual describes setting the GPIB interface address only.

The IEEE interface programming commands can be found in the Digital Interface

Command Reference manual (document 83550100) downloadable from the PHV product

page: http://www.us.tdk-lambda.com/hp/product_html/PHVpower.htm.

The IEEE interface is located on the rear panel of the power supply. A sketch is shown

below.

IEEE Interface features

1- IEEE-488 interface connector

2- Configuration DIP switch (see section 2.1)

3- Interface Addressed LED (see section 1.2)

4- Service Request LED (see section 1.3

1.2. ADDR LED

This LED illuminates when the interface is either in listener addressed state or talker

addressed state.

1.3. Service Request (SRQ) LED

This LED illuminates when the interface asserts the SRQ line. After a serial poll the LED

extinguishes.

83550130 Revision A

THIS PAGE LEFT INTENTIONALLY BLANK

83550130 Revision A

2. Interface setup information

For normal operation, only the GPIB primary address should be adjusted using switches 1

through 5 if required. The other switches, 6 through 8 remain in the OFF position.

2.1. GPIB primary address (PA)

The GPIB primaryaddress (PA) enables identification of all units connected to an IEEE-488

bus system, and each unit connected to the bus must be assigned a unique PA.

The Host PC usually has PA=0 and the connected units usually have addresses from 4

upwards. Normally PHV power supplies arefactory configured with the PA set to 8.

The user can change the factory set PA via a DIP switch located on the IEEE-488 interface

converter on the rear panel of the unit (see the figure on page 3). It is not necessary to

open the power supply.

After changing a configuration switch, the power supply should be turned off for 5 seconds

and turned on again.

To change the GPIB PA, the user should only change switches 1 through 5. The unit is

factory set with switch 4 in the ON position and switches 1, 2, 3, and 5 are in the OFF

position (PA=8).

The switch settings follow the binary system:

Switch 1 has value 1

Switch 2 has value 2

Switch 3 has value 4

Switch 4 has value 8

Switch 5 has value 16

Example: To set the GPIB PA to 9, Switches 1 and 4 are ON, switches 2, 3, and 5 are

OFF. To set the GPIB PA to 20, Switches 3 and 5 are ON, switches 1, 2, and 4 are OFF.

2.2. Other DIP switch settings

DIP switches 6, 7, and 8 are special functions and are factory set to the OFF position and

the settings should not be changed. Contact the factory for further information.

Autres manuels pour PHV Series

Table des matières

Autres manuels TDK-Lambda Alimentation

TDK-Lambda

TDK-Lambda Z+ series Manuel utilisateur

TDK-Lambda

TDK-Lambda GWS250 Series Manuel utilisateur

TDK-Lambda

TDK-Lambda 203 Manuel utilisateur

TDK-Lambda

TDK-Lambda CUS800M Manuel utilisateur

TDK-Lambda

TDK-Lambda CC-P-E Series Manuel utilisateur

TDK-Lambda

TDK-Lambda CUS60M Manuel utilisateur

TDK-Lambda

TDK-Lambda Z10-20 Manuel utilisateur

TDK-Lambda

TDK-Lambda RKY Series Manuel utilisateur

TDK-Lambda

TDK-Lambda LZS-A1500-3-001 Manuel utilisateur

TDK-Lambda

TDK-Lambda Genesys GENH6-100 Manuel utilisateur

TDK-Lambda

TDK-Lambda Genesys Series Manuel utilisateur

TDK-Lambda

TDK-Lambda DDA Series Manuel utilisateur

TDK-Lambda

TDK-Lambda DRJ120 Series Manuel utilisateur

TDK-Lambda

TDK-Lambda Z+ series Manuel utilisateur

TDK-Lambda

TDK-Lambda HWS1000 Series Manuel utilisateur

TDK-Lambda

TDK-Lambda Genesys Manuel utilisateur

TDK-Lambda

TDK-Lambda Genesys GEN6-100 Manuel utilisateur

TDK-Lambda

TDK-Lambda FPS1000-12 Manuel utilisateur

TDK-Lambda

TDK-Lambda ELV60 Series Manuel utilisateur

TDK-Lambda

TDK-Lambda GH10-150 Guide de configuration

TDK-Lambda

TDK-Lambda 2U GENESYS 5KW Manuel utilisateur

TDK-Lambda

TDK-Lambda ZWD150PAF Series Manuel utilisateur

TDK-Lambda

TDK-Lambda 500A Manuel utilisateur

TDK-Lambda

TDK-Lambda DRB120 Series Manuel utilisateur

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur