TCL LIFEDETECT Manuel utilisateur
Quick Start Guide
2
What's In The Box?
LIFEDETECT x 1 Bracket x 1 Screw x 1
Quick start guide
Adhesive x 1 Quick start guide x 1 Wall plug x 1
3
Specification
Product name LIFEDETECT
Model name MS01
Working temperature -5℃ ~ +40℃
Working humidity 0~95%RH, no condensation
Detection range 8 m
Horizontal detect angle 110°
Battery model CR2450
Battery life > 2 years
Operating frequency 2.4 GHz
Transmitted power 8±2dbm
4
Getting to Know Your LIFEDETECT
LIFEDETECT is a Zigbee infrared detection sensor which can detect
humans and large animals. It is designed to work together with a
LIFECONNECT device. You can place it on a desk or install it on a
wall using adhesive or screws.
Note:
• This product can only be used indoors.
• This device requires a LIFECONNECT device in order to function
properly.
Lens (LED Indicator Inside)
Reset Hole
LED Indicators
Flashing blue Searching for LIFECONNECT
Constant blue Connected to LIFECONNECT
Flashing red • Motion detection before joining Zigbee network.
• Low battery
5
Connecting Your LIFEDETECT
1. Make sure that LIFECONNECT is connected to your router.
2. Open your LIFE App, log in your account and select “+” in the App.
Follow the on-screen instructions in the App to add and configure
your LIFEDETECT.
3. Open the battery cover, take out the battery and the insulation
tape (FCC ID could be seen here), and then replace the battery
and battery cover. The LED light will turn blue to indicate it is
booting up.
6 7
4. Remove the protective film from the lens.
5. If you have added your LIFEDETECT successfully, you will see
the LIFEDETECT home page in your LIFE App. If it has not been
added, please use the pin to long press the reset hole for 3
seconds until it flashes blue, then add the LIFEDETECT again in
the App.
7
Relinking Your LIFEDETECT
If you want to link your LIFEDETECT with another LIFECONNECT,
you can follow the steps below:
1. Keep LIFEDETECT online (connect LIFECONNECT) and remove
it from the App. Enter LIFEDETECT home page -> settings ->
Delete LIFEDETECT.
2. Long press the reset hole for more than 3 seconds.
3. Press '+' and follow the instructions within the App.
4. Stand in front of your LIFEDETECT and check for a message in
the App to ensure it is working correctly.
8 9
Installing Your LIFEDETECT
Effective range: Please stand in front of your LIFEDETECT to see
if the LIFE App can receive detection messages before fixing your
LIFEDETECT to a table or wall.
• If yes, it means the Zigbee distance is suitable.
• If not, please select a location closer to your LIFECONNECT.
The recommended distance between LIFEDETECT and
LIFECONNECT is 5~10 m.
Desktop Installation
Place your LIFEDETECT on the table close to the edge and aligned
with the area which you want to detect. Please try to ensure that it
is close to the edge of the table or cabinet.
The recommended installation height is 0.5~1.5m. Please refer to
Detection Range to select your best installation solution.
9
Wall Installation
Mount your LIFEDETECT on a smooth wall using the provided
adhesive or screw.
Desktop Installation Wall Installation
0.5~1.5m
0.5~1.5m
10
Detection Range
Top view
Side view
Note:
If you place the LIFEDETECT upside
down, the detection range will
be inverted. Please position your
LIFEDETECT in such a way to best meet
your requirements.
110°
8 m
8 m
TCL
0.5 m
1 m
41°
8 m
2 m
1 m
41°
3 m
1.5 m
8 m
8 m
41°
41°
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels TCL Accessoires
