Operation
System Parameter Setting
• Long press M and key in the same time for 2s, prepare for setup system parameter: output PWM
frequence, output brightness curve, automatic blank screen. short press M key to switch three item.
• Output PWM frequence: short press or key to switch 500Hz(“F-L”) or 2KHz(“F-H”).
Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for
camera(No flickers for video).
• Output brightness curve: short press or key to switch linear curve(“C-L”) or logarithmic curve(“C-E”).
• Automatic blank screen: short press or key to switch enable (“bon”) or disable(“boF”) automatic
blank screen.
• Long press M key for 2s or timeout 10s, quit system parameter setting.
User Manual Ver 1.0.7 Page 2
D3 -L 3 C hannel Constant Voltage DMX512 & R DM Decoder
Dimming curve setting
Linear dimming curve Logarithmic dimming curve
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
50 60 70 80 90 100
Brightness(%)
10 2 0 3 0 40
Gamma=1.6
50 6 0 7 0 80 90 1 00
Brightness(%)
10 2 0 3 0 40
Gamma=1.0
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
Long press ◀and ▶key for 2s, restore factory default parameter, display "RES".
Factory default parameter: DMX decode mode, DMX decode start address is 1, high PWM frequence output,
logarithmic brightness curve, RGB mode number is 1, dimmer mode number is 1, disable automatic blank screen.
Enter stand-alone dimmer mode onlywhen DMX signal is disconnected or lost.
Short press Mkey, when display L-1~L-8, enter stand-alone dimmer mode.
Press ◀or ▶key to change dimmer mode number(L-1~L-8).
Each dimmer mode can adjust each channel brightness independently.
Long press M key for 2s , prepare for setup three channel brightness.
Short press M key to switch three channel(100~1FF, 200~2FF, 300~3FF).
Press ◀or ▶key to setup brightness value of each channel.
Long press M key for 2s, or timeout 10s, quit setting.
Stand-alone dimmer mode
(L- 1~L- 8)
Malfunctions analysis & troubleshooting
1. Wrong connection of R/G/B wires.
2. DMX decode address error.
Causes
1. Output cable is too long.
2. Wire diameter is too small.
3. Overload beyond power supply capability.
4. Overload beyond controller capability.
Wrong colour
Malfunctions
Uneven intensity
between front and
rear, with voltage drop
No light
RGB change mode list
No. Name
P01
P02
P03
P04
P05
P06
P07
P08
P09
P10
Static red
Static green
Static blue
Static yellow
Static cyan
Static purple
Static white
RGB jump
7 colour jump
Red strobe
No. Name No. Name
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P25
P26
P27
P28
P29
P30
Green strobe
Blue strobe
White strobe
RGB strobe
7 colour strobe
Red fade in and out
Green fade in and out
Blue fade in and out
White fade in and out
RGBW fade in and out
Red yellow smooth
Green cyan smooth
Blue purple smooth
Blue white smooth
RGB+W smooth
RGBW smooth
RGBY smooth
Yellow cyan purple smooth
RGB smooth
6 colour smooth
Stand-alone RGB mode
Enter stand-alone RGB mode onlywhen DMX signal is disconnected or lost.
Short press Mkey, when display P01~P30, enter stand-alone RGB mode.
Press ◀or ▶key to change dynamic mode number(P01~P30).
Each mode can adjust speed and brightness.
Long press M key for 2s , prepare for setup mode speed and brightness.
Short press M key to switch two item.
Press ◀or ▶key to setup value of each item.
Mode speed: 1-10 level speed(S-1, S-9, S-F).
Mode brightness: 1-10 level brightness(b-1, b-9, b-F).
Long press M key for 2s, or timeout 10s, quit setting.
Speed
(8 level)
Brightness
(10 level,100％)
(P01~P30)
1. Reconnect R/G/B wires.
2. Set corrrect decode address.
Troubleshooting
1. Reduce cable or loop supply.
2. Change wider wire.
3. Replace higher power supply .
4. Add power repeater.
1.Check the power.
2.Check the connection.
Stand-alone dimmer mode
Restore factory default parameter
Stand-alone RGB mode
Short press M key, when display 001~999, enter DMX mode.
Press ◀or ▶key to change DMX decode star t address(001~999 ),
long press for fast adjustment.
If there is a DMX signal input, will enter DMX mode automatically.
DMX Dimming: Each D3-L DMX decoder occupy 3 DMX address
when connecting the DMX console.
For example, the defaulted start address is 1,
their corresponding relationship in the form:
DMX mode
DMX mode
(001~999)
Long press M and ◀key in the same time for 2s, prepare for setup system parameter: output PW M frequence, output brightness
curve, automatic blank screen. short press M key to switch three item.
Output PW M frequence: short press ◀or ▶key to switch 500Hz("F-L")or 2KHz("F-H").
Higher PW M frequency, will cause lower output current, higher power noise, but more suitable for camera(No flickers for video).
Output brightness curve: short press ◀or ▶key to switch linear curve("C-L") or logarithmic curve("C-E").
Automatic blank screen: short press ◀or ▶key to switch enable ("bon") or disable("boF") automatic blank screen.
Long press M key for 2s or timeout 10s, quit system parameter setting.
Operation
System parameter setting
CH1 0-255
CH2 0-255
CH3 0-255
CH1 PWM 0-100% (LED R)
DMX Console DMX Decoder Output
CH2 PWM 0-100% (LED G)
CH3 PWM 0-100% (LED B)
1. No power.
2. Wrong connection or insecure.
DMX Mode
• Short press M key, when display 001~999, enter DMX mode.
• Press or key to change DMX decode start
address(001~999), long press for fast adjustment.
• If there is a DMX signal input, will enter DMX mode
automatically.
• DMX Dimming: Each D3-L DMX decoder occupy 3 DMX
address when connecting the DMX console.
For example, the defaulted start address is 1, their
corresponding relationship in the form:
User Manual Ver 1.0.7 Page 2
D3 -L 3 C hannel Constant Voltage DM X512 & RDM Decoder
Dimming curve setting
Linear dimming curve Logarithmic dimming curve
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
50 60 70 80 90 100
Brightness(%)
10 20 3 0 4 0
Gamma=1.6
50 60 7 0 8 0 9 0 100
Brightness(%)
10 20 3 0 4 0
Gamma=1.0
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
Long press ◀and ▶key for 2s, restore factory default parameter, display "RES".
Factory default parameter: DMX decode mode, DMX decode start address is 1, high PWM frequence output,
logarithmic brightness curve, RGB mode number is 1, dimmer mode number is 1, disable automatic blank screen.
Enter stand-alone dimmer mode onlywhen DMX signal is disconnected or lost.
Short press Mkey, when display L-1~L-8, enter stand-alone dimmer mode.
Press ◀or ▶key to change dimmer mode number(L-1~L-8).
Each dimmer mode can adjust each channel brightness independently.
Long press M key for 2s, prepare for setup three channel brightness.
Short press M key to switch three channel(100~1FF, 200~2FF, 300~3FF).
Press ◀or ▶key to setup brightness value of each channel.
Long press M key for 2s, or timeout 10s, quit setting.
Stand-alone dimmer mode
(L- 1~L- 8)
Malfunctions analysis & troubleshooting
1. Wrong connection of R/G/B wires.
2. DMX decode address error.
Causes
1. Output cable is too long.
2. Wire diameter is too small.
3. Overload beyond power supply capability.
4. Overload beyond controller capability.
Wrong colour
Malfunctions
Uneven intensity
between front and
rear, with voltage drop
No light
RGB change mode list
No. Name
P01
P02
P03
P04
P05
P06
P07
P08
P09
P10
Static red
Static green
Static blue
Static yellow
Static cyan
Static purple
Static white
RGB jump
7 colour jump
Red strobe
No. Name No. Name
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P25
P26
P27
P28
P29
P30
Green strobe
Blue strobe
White strobe
RGB strobe
7 colour strobe
Red fade in and out
Green fade in and out
Blue fade in and out
White fade in and out
RGBW fade in and out
Red yellow smooth
Green cyan smooth
Blue purple smooth
Blue white smooth
RGB+W smooth
RGBW smooth
RGBY smooth
Yellow cyan purple smooth
RGB smooth
6 colour smooth
Stand-alone RGB mode
Enter stand-alone RGB mode onlywhen DMX signal is disconnected or lost.
Short press Mkey, when display P01~P30, enter stand-alone RGB mode.
Press ◀or ▶key to change dynamic mode number(P01~P30).
Each mode can adjust speed and brightness.
Long press M key for 2s, prepare for setup mode speed and brightness.
Short press M key to switch two item.
Press ◀or ▶key to setup value of each item.
Mode speed: 1-10 level speed(S-1, S-9, S-F).
Mode brightness: 1-10 level brightness(b-1, b-9, b-F).
Long press M key for 2s, or timeout 10s, quit setting.
Speed
(8 level)
Brightness
(10 level,100％)
(P01~P30)
1. Reconnect R/G/B wires.
2. Set corrrect decode address.
Troubleshooting
1. Reduce cable or loop supply.
2. Change wider wire.
3. Replace higher power supply .
4. Add power repeater.
1.Check the power.
2.Check the connection.
Stand-alone dimmer mode
Restore factory default parameter
Stand-alone RGB mode
Short press M key, when display 001~999, enter DMX mode.
Press ◀or ▶key to change DMX decode star t address(001 ~999 ),
long press for fast adjustment.
If there is a DMX signal input, will enter DMX mode automatically.
DMX Dimming: Each D3-L DMX decoder occupy 3 DMX address
when connecting the DMX console.
For example, the defaulted start address is 1,
their corresponding relationship in the form:
DMX mode
DMX mode
(001~999)
Long press M and ◀key in the same time for 2s, prepare for setup system parameter: output PW M frequence, output brightness
curve, automatic blank screen. short press M key to switch three item.
Output PW M frequence: short press ◀or ▶key to switch 500Hz("F-L")or 2KHz("F-H").
Higher PW M frequency, will cause lower output current, higher power noise, but more suitable for camera(No flickers for video).
Output brightness curve: short press ◀or ▶key to switch linear curve("C-L") or logarithmic curve("C-E").
Automatic blank screen: short press ◀or ▶key to switch enable ("bon") or disable("boF") automatic blank screen.
Long press M key for 2s or timeout 10s, quit system parameter setting.
Operation
System parameter setting
CH1 0-255
CH2 0-255
CH3 0-255
CH1 PWM 0-100% (LED R)
DMX Console DMX Decoder Output
CH2 PWM 0-100% (LED G)
CH3 PWM 0-100% (LED B)
1. No power.
2. Wrong connection or insecure.
Stand-alone RGB Mode
• Enter stand-alone RGB mode only when DMX signal is disconnected or lost.
• Short press M key, when display P01~P30, enter stand-alone RGB mode.
• Press or key to change dynamic mode number(P01~P30).
• Each mode can adjust speed and brightness.
Long press M key for 2s, prepare for setup mode speed and brightness.
Short press M key to switch two item.
Press or key to setup value of each item.
Mode speed: 1-10 level speed(S-1, S-9, S-F).
Mode brightness: 1-10 level brightness(b-1, b-9, b-F).
Long press M key for 2s, or timeout 10s, quit setting.
User Manual Ver 1.0.7 Page 2
D3 -L 3 C hannel Constant Voltage DM X512 & RDM Decoder
Dimming curve setting
Linear dimming curve Logarithmic dimming curve
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
50 60 70 80 90 100
Brightness(%)
10 20 3 0 4 0
Gamma=1.6
50 60 7 0 8 0 9 0 100
Brightness(%)
10 20 3 0 4 0
Gamma=1.0
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
Long press ◀and ▶key for 2s, restore factory default parameter, display "RES".
Factory default parameter: DMX decode mode, DMX decode start address is 1, high PWM frequence output,
logarithmic brightness curve, RGB mode number is 1, dimmer mode number is 1, disable automatic blank screen.
Enter stand-alone dimmer mode onlywhen DMX signal is disconnected or lost.
Short press Mkey, when display L-1~L-8, enter stand-alone dimmer mode.
Press ◀or ▶key to change dimmer mode number(L-1~L-8).
Each dimmer mode can adjust each channel brightness independently.
Long press M key for 2s, prepare for setup three channel brightness.
Short press M key to switch three channel(100~1FF, 200~2FF, 300~3FF).
Press ◀or ▶key to setup brightness value of each channel.
Long press M key for 2s, or timeout 10s, quit setting.
Stand-alone dimmer mode
(L- 1~L- 8)
Malfunctions analysis & troubleshooting
1. Wrong connection of R/G/B wires.
2. DMX decode address error.
Causes
1. Output cable is too long.
2. Wire diameter is too small.
3. Overload beyond power supply capability.
4. Overload beyond controller capability.
Wrong colour
Malfunctions
Uneven intensity
between front and
rear, with voltage drop
No light
RGB change mode list
No. Name
P01
P02
P03
P04
P05
P06
P07
P08
P09
P10
Static red
Static green
Static blue
Static yellow
Static cyan
Static purple
Static white
RGB jump
7 colour jump
Red strobe
No. Name No. Name
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P25
P26
P27
P28
P29
P30
Green strobe
Blue strobe
White strobe
RGB strobe
7 colour strobe
Red fade in and out
Green fade in and out
Blue fade in and out
White fade in and out
RGBW fade in and out
Red yellow smooth
Green cyan smooth
Blue purple smooth
Blue white smooth
RGB+W smooth
RGBW smooth
RGBY smooth
Yellow cyan purple smooth
RGB smooth
6 colour smooth
Stand-alone RGB mode
Enter stand-alone RGB mode onlywhen DMX signal is disconnected or lost.
Short press Mkey, when display P01~P30, enter stand-alone RGB mode.
Press ◀or ▶key to change dynamic mode number(P01~P30).
Each mode can adjust speed and brightness.
Long press M key for 2s, prepare for setup mode speed and brightness.
Short press M key to switch two item.
Press ◀or ▶key to setup value of each item.
Mode speed: 1-10 level speed(S-1, S-9, S-F).
Mode brightness: 1-10 level brightness(b-1, b-9, b-F).
Long press M key for 2s, or timeout 10s, quit setting.
Speed
(8 level)
Brightness
(10 level,100％)
(P01~P30)
1. Reconnect R/G/B wires.
2. Set corrrect decode address.
Troubleshooting
1. Reduce cable or loop supply.
2. Change wider wire.
3. Replace higher power supply .
4. Add power repeater.
1.Check the power.
2.Check the connection.
Stand-alone dimmer mode
Restore factory default parameter
Stand-alone RGB mode
Short press M key, when display 001~999, enter DMX mode.
Press ◀or ▶key to change DMX decode star t address(001 ~999 ),
long press for fast adjustment.
If there is a DMX signal input, will enter DMX mode automatically.
DMX Dimming: Each D3-L DMX decoder occupy 3 DMX address
when connecting the DMX console.
For example, the defaulted start address is 1,
their corresponding relationship in the form:
DMX mode
DMX mode
(001~999)
Long press M and ◀key in the same time for 2s, prepare for setup system parameter: output PW M frequence, output brightness
curve, automatic blank screen. short press M key to switch three item.
Output PW M frequence: short press ◀or ▶key to switch 500Hz("F-L")or 2KHz("F-H").
Higher PW M frequency, will cause lower output current, higher power noise, but more suitable for camera(No flickers for video).
Output brightness curve: short press ◀or ▶key to switch linear curve("C-L") or logarithmic curve("C-E").
Automatic blank screen: short press ◀or ▶key to switch enable ("bon") or disable("boF") automatic blank screen.
Long press M key for 2s or timeout 10s, quit system parameter setting.
Operation
System parameter setting
CH1 0-255
CH2 0-255
CH3 0-255
CH1 PWM 0-100% (LED R)
DMX Console DMX Decoder Output
CH2 PWM 0-100% (LED G)
CH3 PWM 0-100% (LED B)
1. No power.
2. Wrong connection or insecure.
Stand-alone Dimmer Mode
• Enter stand-alone dimmer mode only when DMX signal is disconnected or lost.
• Short press M key, when display L-1~L-8, enter stand-alone dimmer mode.
• Press or key to change dimmer mode number(L-1~L-8).
• Each dimmer mode can adjust each channel brightness independently.
Long press M key for 2s, prepare for setup three channel brightness.
Short press M key to switch three channel(100~1FF, 200~2FF, 300~3FF).
Press or key to setup brightness value of each channel.
Long press M key for 2s, or timeout 10s, quit setting.
User Manual Ver 1.0.7 Page 2
D3 -L 3 C hannel Constant Voltage DM X512 & RDM Decoder
Dimming curve setting
Linear dimming curve Logarithmic dimming curve
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
50 60 70 80 90 100
Brightness(%)
10 20 3 0 4 0
Gamma=1.6
50 60 7 0 8 0 9 0 100
Brightness(%)
10 20 3 0 4 0
Gamma=1.0
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
Long press ◀and ▶key for 2s, restore factory default parameter, display "RES".
Factory default parameter: DMX decode mode, DMX decode start address is 1, high PWM frequence output,
logarithmic brightness curve, RGB mode number is 1, dimmer mode number is 1, disable automatic blank screen.
Enter stand-alone dimmer mode onlywhen DMX signal is disconnected or lost.
Short press Mkey, when display L-1~L-8, enter stand-alone dimmer mode.
Press ◀or ▶key to change dimmer mode number(L-1~L-8).
Each dimmer mode can adjust each channel brightness independently.
Long press M key for 2s, prepare for setup three channel brightness.
Short press M key to switch three channel(100~1FF, 200~2FF, 300~3FF).
Press ◀or ▶key to setup brightness value of each channel.
Long press M key for 2s, or timeout 10s, quit setting.
Stand-alone dimmer mode
(L- 1~L- 8)
Malfunctions analysis & troubleshooting
1. Wrong connection of R/G/B wires.
2. DMX decode address error.
Causes
1. Output cable is too long.
2. Wire diameter is too small.
3. Overload beyond power supply capability.
4. Overload beyond controller capability.
Wrong colour
Malfunctions
Uneven intensity
between front and
rear, with voltage drop
No light
RGB change mode list
No. Name
P01
P02
P03
P04
P05
P06
P07
P08
P09
P10
Static red
Static green
Static blue
Static yellow
Static cyan
Static purple
Static white
RGB jump
7 colour jump
Red strobe
No. Name No. Name
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P25
P26
P27
P28
P29
P30
Green strobe
Blue strobe
White strobe
RGB strobe
7 colour strobe
Red fade in and out
Green fade in and out
Blue fade in and out
White fade in and out
RGBW fade in and out
Red yellow smooth
Green cyan smooth
Blue purple smooth
Blue white smooth
RGB+W smooth
RGBW smooth
RGBY smooth
Yellow cyan purple smooth
RGB smooth
6 colour smooth
Stand-alone RGB mode
Enter stand-alone RGB mode onlywhen DMX signal is disconnected or lost.
Short press Mkey, when display P01~P30, enter stand-alone RGB mode.
Press ◀or ▶key to change dynamic mode number(P01~P30).
Each mode can adjust speed and brightness.
Long press M key for 2s, prepare for setup mode speed and brightness.
Short press M key to switch two item.
Press ◀or ▶key to setup value of each item.
Mode speed: 1-10 level speed(S-1, S-9, S-F).
Mode brightness: 1-10 level brightness(b-1, b-9, b-F).
Long press M key for 2s, or timeout 10s, quit setting.
Speed
(8 level)
Brightness
(10 level,100％)
(P01~P30)
1. Reconnect R/G/B wires.
2. Set corrrect decode address.
Troubleshooting
1. Reduce cable or loop supply.
2. Change wider wire.
3. Replace higher power supply .
4. Add power repeater.
1.Check the power.
2.Check the connection.
Stand-alone dimmer mode
Restore factory default parameter
Stand-alone RGB mode
Short press M key, when display 001~999, enter DMX mode.
Press ◀or ▶key to change DMX decode star t address(001 ~999 ),
long press for fast adjustment.
If there is a DMX signal input, will enter DMX mode automatically.
DMX Dimming: Each D3-L DMX decoder occupy 3 DMX address
when connecting the DMX console.
For example, the defaulted start address is 1,
their corresponding relationship in the form:
DMX mode
DMX mode
(001~999)
Long press M and ◀key in the same time for 2s, prepare for setup system parameter: output PW M frequence, output brightness
curve, automatic blank screen. short press M key to switch three item.
Output PW M frequence: short press ◀or ▶key to switch 500Hz("F-L")or 2KHz("F-H").
Higher PW M frequency, will cause lower output current, higher power noise, but more suitable for camera(No flickers for video).
Output brightness curve: short press ◀or ▶key to switch linear curve("C-L") or logarithmic curve("C-E").
Automatic blank screen: short press ◀or ▶key to switch enable ("bon") or disable("boF") automatic blank screen.
Long press M key for 2s or timeout 10s, quit system parameter setting.
Operation
System parameter setting
CH1 0-255
CH2 0-255
CH3 0-255
CH1 PWM 0-100% (LED R)
DMX Console DMX Decoder Output
CH2 PWM 0-100% (LED G)
CH3 PWM 0-100% (LED B)
1. No power.
2. Wrong connection or insecure.
