Malfunction Analysis and Troubleshooting
User Manual Ver 1.0.3 Page 2
Match Remote Control (two match ways)
Use the controller’ s Match key
Match:
Short press match key, immediately press on/off
key (single zone remote) or zone key (multiple zone
remote) of the remote.
Use Power Restar t
Match:
Switch off the power, then switch on power again,
immediately short press on/off key 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power again,
immediately short press on/off key 5 times on the remote.
The light blinks 5 times means all matched remotes were
deleted.
Delete:
Press and hold match key for 5s to delete all match,
The light blinks 5 times means all matched remotes
were deleted.
End user can choose the suitable match/ delete ways. Two options are offered for selection:
Bright-
Mode
Color wheel
Speed/Saturation
Turn on/off light.
Color wheel: Touch to change static RGB color.
Mode: Short press run the next dynamic mode, long press 2s run mode cycle.
Speed/Saturation : For dynamic mode, adjust speed, short press 10 levels long press 2s get the default speed.,
For static color, adjust saturation, namely change current static RGB color to mixed white slowly,
short press 11 levels, long press 1-5s for continuous 256 levels adjustment.
Bright+/-: Adjust brightness, short press 10 levels long press 1-5s for continuous256 levels adjustment.,
/ / ,R G B: Short press getred green or bluecolor directly,
long press 1-5s adjust R/G/B brightnesscontinuously toachieve millions of colors.
continuouslyW+/-: Short press turn on/off white(RGB mix), long press 1-5s adjust saturation ,
namely change current static RGB color to mixed white slowly.
Scene: Short press recall the scene long press 2s savethe currentcolor into the scene.,
R emote f unction
On/ Off
R/ G/ B/ W+/-
Scene
Bright+
V3 + R8-1 RGB LED Strip Controller Kit
* When light is on, touchthe color wheel,the indicator will display red.
* To extendbattery life,no touch or press key operationafter afew seconds,
the touch wheel will enter sleep state, youneed press any key to make touch wheel quit sleep state.
M a lfunctions a na lysis & t roubleshooting
Malfunctions
Causes
Uneven intensity
between front and
rear,with voltage drop
1. Output cable is too long.
2. Wire diameter is too small.
3. Overload beyond power supply capability.
4. Overload beyond controller capability.
No response
from the remote
1. The battery has no power.
2. Beyond controllable distance.
3. The controller did not match the remote .
No light
Troubleshooting
1. Reduce cable or loop supply.
2. Change wider wire.
3. Replace higher power supply.
4. Add power repeater.
1. Replace battery.
2. Reduce remote distance.
3. Re-match the remote.
1.Check the power.
2.Check the connection.
Dyna mic m ode l ist
RGB jump
RGB smooth
6 colour jump
6 colour smooth
Yellow cyan purple smooth
1
2
3
4
5
6
7
8
9
10
RGB fade in and out
Red fade in and out
Green fade in and out
Blue fade in and out
White fade in and out
A pplica tion notes
All the receivers are matched with one RF remote.
RF remote
30m 30m
Auto-transmitting:One receiver can transmit the signals from the remote to another receiver within 30m,
as long as there is a receiver within 30m, the remote control distance can be limitless.
Auto-synchronization: Multiple receivers within 30m distance can work synchronously when they are controlled
by the same remote, under same dynamic mode and with same speed.
Receiver placement may offer up to 30m communication distance. However, we recommend for indoor applications
that receiver placements should be no further apart than15m.
30m
1. No power.
2. Wrong connection or insecure.
Safety Information
1. The product shall be installed and serviced by a qualified person.
2. The product is non-waterproof. Please avoid the sun and rain.
3. Good heat dissipation will prolong the working life of the controller. Please ensure good
ventilation.
4. Please check if the output voltage of any power supplies used comply with the working
voltage of the product.
5. Ensure all wire connections and polarities are correct and secure before applying power to
avoid any damages to the LED lights.
6. If a fault occurs please return the product to your supplier. Do not attempt to fix this
product by yourself.
LED power supply voltage and power select:
• 5V lamp, Input 5V power supply, can load 0~40W,
• 12V lamp, Input 12V power supply, can load 0~96W,
• 24V lamp, Input 24V power supply, can load 0~192W,
• 36V lamp, Input 36V power supply, can load 0~288W,
The power supply power must larger than load power 20%.
