Targus DEFCON 3 Manuel utilisateur
Portable Security System
User’s Guide
INTRODUCTION
Congratulations on your purchase of the Targus DEFCON 3 Security
System - you have selected the most advanced personal property protection
available. Now your briefcase, computer, and other personal property are
as safe on the road as they are in your home or office!
This user’s guide provides descriptions of the DEFCON 3 features and
functions, and gives instructions for installing the batteries, activating,
programming, arming, disarming, and deactivating the DEFCON 3 alarm
unit.
Figure 1. Front and Back View of DEFCON 3 Alarm Unit
Contents
DEFCON 3 alarm unit
DEFCON 3 remote control (with ANSI/NEDA 1811A, or
equivalent, battery installed)
3 AAA Alkaline batteries (for use with alarm unit)
This user’s guide
DEFCON 3 AT A GLANCE
The DEFCON 3 Security System provides a number of options through its
programmable features - the electronic motion sensor, the alarm siren
sound, and alarm volume.
1
Features
Electronic Motion Sensor Triggers the alarm when motion is
detected. You can choose from two
different sensitivity settings.
Level 1 - Low Motion Sensitivity (default)
Level 2 - High Motion Sensitivity
Alarm Volume 84dB - Low Volume
94dB - High Volume (default)
Alarm Siren Choice of six different sounds
Remote Control Allows easy control of all features and
functions of your alarm unit from up to
40 feet away.
Panic Alarm/Locator Sounds an immediate alarm siren for
personal protection or to locate the alarm
unit and the item to which it’s attached.
LED Lights Provide visual warning and alarm status
ACTIVATING THE ALARM UNIT
The DEFCON 3 Security System is designed to work with a specific
remote control. To activate the alarm unit, you must first transmit a signal
from its remote control device. Once the alarm unit has received the unique
remote control ID code, it only responds to that remote control and ignores
other signals.
Figure 2. Remote Control - Front, Back, and Interior Views
2
3
4
5
Installing Batteries
Figure 3. Installing Batteries in the Alarm Unit
1. Unscrew the end of the cable to detach it.
2. Remove the screw and battery cover from the back of
the alarm unit.
3. Insert the batteries in place as shown in Figure 3.
4. Replace the battery cover and screw.
5. Reattach the cable.
6. The LED lights should now flash alternately. This means
your alarm unit is waiting for a signal from your remote
control. (A battery is already installed in the remote control.)
See Table B for the LED lights legend.
7. Press and hold either button on the remote control until the
alarm unit beeps six times and the LED lights stop flashing.
Note: Whenever you insert or replace the batteries in the alarm unit,
you must press and hold either button on the remote control until the
alarm beeps six times and the LED lights stop flashing.
The remote control ID code has been successfully transmitted and
stored in memory.
6
Programming a New Remote Control
When you need to program a new remote control for the alarm unit:
1. Remove the batteries from the alarm unit for at least
10 minutes.
2. Replace the batteries.
3. Press and hold either button on the remote control until the
alarm unit beeps six times and the LED lights stop flashing.
Arming and Disarming
The DEFCON 3 alarm unit is easily armed.
Simply press and hold the Arm/Disarm button on the
remote control once.
You will hear one chirp, and the left LED light will flash
(once per second) indicating the unit is active .
If the DEFCON 3 detects excessive motion while armed, it warns with a
continuous tone, then sounds a loud siren for 30 seconds. The alarm unit
resets itself against additional threats.
To disarm the DEFCON 3 (and silence the alarm siren):
Press and hold the Arm/Disarm button once again.
The LED light goes out. Next, you will hear two chirps, or
three chirps if the siren sounded while you were away.
Panic Alarm/Locator
You may need to instantly activate the alarm siren for personal protection,
theft deterrence, or to locate the alarm unit itself.
To activate the alarm siren, simultaneously press and hold both buttons on
the remote control.
To deactivate the alarm siren, press and hold any button on the remote
control.
7
PROGRAMMING DEFCON 3 FEATURES
The DEFCON 3 has a Program Mode that enables you to tailor the alarm
unit to your personal preferences through several advanced features.
Accessing Program Mode
1. Make sure the alarm unit is not armed.
2. Press and hold the Program button on the remote control
for three seconds, or until you hear four beeps and the right
LED light glows red: First then .
You are now in Program Mode. If the alarm does not receive a
signal from the remote control for 20 seconds, it will
automatically exit Program Mode. When this occurs, the alarm
unit sounds four short beeps and the LED light goes out.
Navigating Program Mode
Once in Program Mode, you can begin to cycle through the programmable
features.
1. Make sure the alarm unit is not armed.
2. Press and hold the Program button on the remote
control to cycle through the feature’s options in the
following order:
✤motion sensitivity
✤alarm volume
✤alarm siren sound
When cycling through the feature’s options, the first choice is either the
factory default, or the selection presently in use by the DEFCON 3
Security System. The last selection you make for each feature is the one
that will be stored in the alarm unit’s memory.
3. Press and hold the Arm/Disarm button on the remote
control to make your selection.
If you accidentally bypass a feature, continue pressing the Program button
to cycle back to it. For example, if you want to change the alarm volume
but you are in the alarm siren feature, press the Program button once to
advance to the motion sensitivity feature. Press it again to advance to the
alarm volume feature.
8
Setting Motion Sensitivity
The DEFCON 3 alarm unit has two sensitivity settings:
Low Motion Sensitivity (Level 1): First then .
This setting triggers the alarm siren when the unit has detected continuous
motion for six seconds. This is the factory default.
High Motion Sensitivity (Level 2): First then .
This setting triggers the alarm siren after just two seconds of continuous
excessive motion.
NOTE: This alarm is not designed for use in moving vehicles such as
buses, automobiles, trains, or airplanes.
1. Access Program Mode.
2. Press and hold the Arm/Disarm button to cycle between the
two options.
One short beep indicates Low Motion Sensitivity; two short beeps
indicate High Motion Sensitivity.
3. Make your selection for the motion sensitivity setting.
4. Press and hold the Program button for one second to
advance to the next programmable feature - alarm volume.
Note: The alarm siren will sound under the following conditions:
✤Excessive motion is detected
Upon detecting motion, both LEDs will light up and a
continuous tone will sound as a warning that the alarm siren
is about to go off. After 30 seconds, the alarm siren stops,
and the alarm unit automatically rearms itself at the current
motion sensitivity setting.
✤If an attempt to unscrew the alarm unit cable is made (two
and a half complete turns)*
✤If the screw that holds the battery cover in place is turned (a
half turn)*
✤If you activate the Panic Alarm*
*Under these three conditions, the alarm siren can be turned off
only from the remote control.
9
Setting Alarm Volume
Your DEFCON 3 alarm unit has two volume settings:
High Volume - 94 dB (Default setting)
Low Volume - 84 dB
1. Access Program Mode. Alarm volume is the second feature
you encounter in Program Mode.
2. To bypass the motion sensitivity feature and program the
alarm volume, press and hold the Program button twice.
For this feature, the right LED light is on, and the left LED light
flashes slowly and continuously .
3. Press and hold the Arm/Disarm button to cycle between the
two volume settings.
A three-second sample alarm will sound at the volume you chose.
4. Press and hold the Program button to advance to the next
programmable feature - alarm siren.
Setting Alarm Siren
Your DEFCON 3 Security System provides a selection of six different
alarm siren sounds.
1. Access Program Mode. The alarm siren is the third feature
you encounter in Program Mode.
2. To bypass the other features and program the alarm siren
sound, press and hold the Program button three times.
For this feature, the right LED light is on, and the left LED light
flashes quickly and continuously .
3. Press and hold the Arm/Disarm button to cycle through the
six siren sounds.
A three-second sample siren will sound at the volume you chose
for each siren sound as you cycle through them.
4. Make your selection for the alarm siren sound.
5. Press and hold the Program button for one second to
advance to Motion Sensitivity Mode, or three seconds to exit
Program Mode and lock your selections into memory.
Table des matières
Autres manuels Targus Système de sécurité
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur