Tannoy CMS 1201DC Manuel utilisateur
CMS 1201DC
Professional Loudspeakers
Operation Manual
2
CMS 3.0 Series Operation Manual rev 3.0.0
Table of Contents
CMS 3.0 Series Operation Manual rev 3.0.0
3
Table of Contents
1. Introduction 4
2. Unpacking and Visual Checks 4
3. Product Overview 5
3.1. Ordering Information ...............................................................................................................................5
4. Installation Guide 6
4.1. Back-can ................................................................................................................................................6
4.2. Mounted Using Unistrut roof rail system .................................................................................................6
4.3. Flying using Eyebolts ..............................................................................................................................7
4.4. Flying using Screwed Rod ......................................................................................................................7
4.5. Fitting the loudspeaker assembly ...........................................................................................................8
4.6. Fitting the grille ....................................................................................................................................... 8
5. Wiring and Setting Up 9
6. Dimensions 9
7. Technical Specications 10
8. Warranty 11
9. Declaration of conformity 11
1. Introduction
4
CMS 3.0 Series Operation Manual rev 3.0.0
1. Introduction
Thank you for purchasing this Tannoy product.
The CMS 1201DC is a powerful state-of-the-art large format in-ceiling loudspeaker device conceived, designed
and built to complement Tannoy’s class-leading CMS range. From the pioneers of point source and large format
ceiling speakers the CMS 1201DC is engineered from the ground up with superior full-range performance in mind
to handle demanding distributed sound applications such as ballrooms, shopping malls, sports halls, airports and
other high ceiling installations.
Built around a brand new evolution of the high power handling 12” (300 mm) Dual Concentric™ point source
driver, the CMS 1201DC delivers best-in-class performance for the most even beamwidth and pattern control
over the widest range of frequencies of any large format ceiling speaker. Coupled with exceptional clarity, ultra low
distortion, and high SPLs, Tannoy has again raised the bar to give the absolute cutting edge performance in ceiling
mounted loudspeaker technology.
The new Dual Concentric drive assembly features a treated mid-bass cone and double rolled cambric surround for
high sensitivity, as well as a 34 mm (1.34”) aluminium dome with ferrouid-cooled Neodymium magnet assembly
and a newly designed waveguide for the high frequency unit. These two drivers seamlessly merge into one with the
high frequency mounted in the throat of the mid-bass; coincidentally aligning both transducers to a point source.
The result is a smooth, uniform response over a very controlled 90 degree coverage area – even in the highest
octaves.
2. Unpacking and Visual Checks
Every Tannoy product and accessory is carefully inspected before packing. After unpacking, please inspect your
product to make sure no damage has occurred in transit. In the unlikely event of any damage, would you please
notify your dealer immediately and retain your shipping carton, as your dealer may ask you to return the faulty
unit to him for inspection.
3. Product Overview
CMS 3.0 Series Operation Manual rev 3.0.0
5
3. Product Overview
The CMS1201 DC comprises three discrete components that are ordered separately under different part
numbers.
• A loudspeaker assembly that includes a Dual Concentric drive unit mounted on a ported steel bafe, and its
crossover. This bafe may also include a line transformer (CMS 1201DCt).
• A steel back-can with multiple mounting points
• A grille assembly with its moulded bevel cover
3.1. Ordering Information
Part Number Description
8001 4750 Loudspeaker CMS 1201DC
8001 4751 Loudspeaker CMS 1201DCt
8001 4760 Back-can - CMS 1201
8001 4780 Grille Assembly - CMS 1201
4. Installation Guide
6
CMS 3.0 Series Operation Manual rev 3.0.0
4. Installation Guide
4.1. Back-can
The custom engineered powder coated steel back-can has been designed to cater for all conceivable
installation possibilities making the CMS 1201DC extremely versatile. Internally dampened with 11 mm (0.43”)
OSB2 board, the addition of the back-can provides exceptional low frequency performance.
4.2. Mounted Using Unistrut roof rail system
Steel mounting lugs allow for tting to a Unistrut roof rail system in a variety of congurations both directly or via
secondary prexed cross struts.
Screw at xing point should use a large series washer to help spread the load.
Speaker mounted to a single rail Back-can mounted between rails
4. Installation Guide
CMS 3.0 Series Operation Manual rev 3.0.0
7
4.3. Flying using Eyebolts
WARNING: As the legal requirements for ying change from country to country, please consult your local safety
standards ofce before installing any product. We also recommend that you thoroughly check any laws and
bylaws prior to commencing work.
The device can also be hung via 4 top-mounted eye bolts. Rear of back can has mounting points for both M10
and 3/8 UNC threaded eyebolts.
4.4. Flying using Screwed Rod
The design also caters for a single point central hang via M10 or 3/8 UNC screwed rod – made easy thanks to
the slotted mounting saddle on the top of the back-can. If required a safety wire can be attached to any of the
M10 ying points.
To t the back can to threaded rod support, rst run a nut 50 mm (2”) up the rod followed by two plain washers
and then a locking nut (Nyloc®). Hook the back can on to the rod between the two plain washers. Once the nut
has cleared the guide slot the top nut can be locked down to secure.
4. Installation Guide
8
CMS 3.0 Series Operation Manual rev 3.0.0
4.5. Fitting the loudspeaker assembly
Mounting of the loudspeaker assembly to the pre-installed back-can is a one man job thanks to the common
sense design approach. One edge of the bafe clips onto the steel box to hold it in place while the installer
secures the assembly in place. Connection is simple via terminal barrier strips inside the can, easily accessible
via 20 mm (0.79“) and 29 mm (1.14”) conduit knockouts on all ve sides of the can. Saving time and manpower
during installation has been a driving factor behind the design of the CMS 1201 system.
Bafe assemble can be hooked onto the back can with care.
4.6. Fitting the grille
5. Wiring and Setting Up
CMS 3.0 Series Operation Manual rev 3.0.0
9
5. Wiring and Setting Up
The CMS 1201 is available in both a standard low-impedance variant (CMS 1201DC) and a low insertion loss
60 W line transformer-equipped version (CMS 1201DCt) for use on 70 V or 100 V distributed lines. The following
tappings are congurable on the transformer before screwing driver assembly into the back can:
70 V systems: 60 W / 30 W / 15 W / 7.5 W / OFF
100 V systems: 60 W / 30 W / 15 W / OFF
If later adjustment to the level is required the bafe can be hung from the can via a hinged edge, leaving both
hands free to make the required adjustment.
Tannoy’s focus on maintaining the highest standards of continuous product performance and reliability, through
uncompromising quality control of components and manufacturing processes, means you can specify and
install CMS 1201DC with condence. As with all of Tannoy’s CMS in-ceiling loudspeakers, the CMS 1201DC
benets from a 5-year warranty.
6. Dimensions
100.0
[3.94"]
588.2
[23.16"]
302.6
[11.91"]
315.0
[12.40"]
24.6
[0.97"]
100.0
[3.94"]
457.0
[17.99"]
725.0
[28.54"]
516.0
[20.31"]
15.3
[0.60"]
60.0
[2.36"]
432.0
[17.01"]
432.0
[17.01"]
7. Technical Specifications
10
CMS 3.0 Series Operation Manual rev 3.0.0
7. Technical Specifications
Performance
Frequency response (-3 dB) (1) 60 Hz - 20 kHz
Frequency range (-10 dB) (1) 45 Hz - 30 kHz
System Sensitivity (1W @ 1m) (2) 97 dB (1 W = 2.83 V for 8 Ohms)
Nominal Coverage Angle 90 Degrees Conical
Coverage Angle (1 kHz to 16 kHz) 90 Degrees Conical
Crossover 1.6 kHz - 2nd order LF, 2nd order HF
Directivity Factor (Q) 8.9
Directivity Index (DI) 9.5
Rated maximum SPL (2)
Average 120 dB
Peak 126 dB
With THP 60 - Average 115 dB
Power Handling
Average 200 W
Programme 400 W
Peak 800 W
Recommended Amplier Power 400 W @ 8 Ohms
Nominal Impedance 8 Ohms
Transformer Taps (CMS 1201DCt only)
70 V 60 W / 30 W / 15 W / 7.5 W / OFF
100 V 60 W / 30 W / 15 W / OFF
Transducers
Low Frequency 1 x 300 mm (12.00”) Dual Concentric™ constant directivity driver
with treated cone
High Frequency 34 mm (1.34”) aluminium done with neodymium magnet system
Distortion
10% full power (5.5 V) Harmonics
2nd 3rd
250 Hz 1.60 0.28
1 kHz 2.45 0.73
10 kHz 4.50 0.32
1% full power (1.73 V)
250 Hz 0.48 0.08
1 kHz 1.06 0.59
10 kHz 1.57 0.04
Physical
Enclosure
Backcan 1.6 mm black powder coated steel, damped with 11 mm OSB board
Bafe 1.2 mm black powder coated steel
Grille 1.0 mm white powder coated perforated steel
Connectors Terminal barrier strip inside the can, with loop thru capability
Safety Features Safety ring located at the rear of enclosure
for load bearing safety bond
Cable Entry Options 20 mm and 28 mm on knockouts
Conduit Knockouts 4 sides + top
Dimensions (H x W x D) 331 x 725 x 516 mm (13.03 x 28.54 x 20.31”)
Net Weight
Backcan 20 kg (44.1 lbs)
Bafe 9 kg (19.8 lbs)
Grille 1.1 kg (2.4 lbs)
Notes:
1. Average over stated bandwidth. Measured in
an IEC bafe in an Anechoic Chamber
2. Unweighted pink noise input, measured at
1 metre on axis
3. Long term power handling capacity as dened
in EIA - 426B test
A full range of measurements, performance data,
CLF and Ease™ Data for CMS 1201DC can be
downloaded from www.tannoypro.com.
Tannoy operates a policy of continuous research
and development. The introduction of new materials
or manufacturing methods may introduce variations
in actual performance; however, actual performance
always will equal or exceed the published
specications, which Tannoy reserves the right to
alter without prior notice. Please verify the latest
specications when dealing with critical applications.
Copyright (c) 2015 Tannoy Limited. All rights reserved.
Ordering Information
Part Number Colour
8001 4750
CMS 1201DC Black
8001 4751
CMS 1201DCt Black
8001 4760
CMS 1201 Backcan Black
8001 4780
CMS 1201 White
Grille Assembly
3212 0141
THP 150 N/A
Transformer
Table des matières
Autres manuels Tannoy Intervenants
Tannoy
Tannoy iw6 DS Discrete Manuel utilisateur
Tannoy
Tannoy V12HP Manuel utilisateur
Tannoy
Tannoy VLS SERIES Manuel utilisateur
Tannoy
Tannoy Prestige Glenair Manuel utilisateur
Tannoy
Tannoy VLS 7 Manuel utilisateur
Tannoy
Tannoy SuperTweeter ST-100 Manuel utilisateur
Tannoy
Tannoy Qflex Manuel utilisateur
Tannoy
Tannoy SR601 Manuel utilisateur
Tannoy
Tannoy SYSTEM 600a Manuel utilisateur
Tannoy
Tannoy EYRIS DUAL CONCENTRIC Manuel utilisateur
Tannoy
Tannoy EYRIS Manuel utilisateur
Tannoy
Tannoy VX 12.2Q Manuel utilisateur
Tannoy
Tannoy VNET 12 Manuel utilisateur
Tannoy
Tannoy CMS801 DC BM Manuel utilisateur
Tannoy
Tannoy PRESTIGE TurnberrySE Manuel utilisateur
Tannoy
Tannoy CMS503DC LP Manuel utilisateur
Tannoy
Tannoy Reveal 402 Manuel utilisateur
Tannoy
Tannoy KINGDOM ROYAL Manuel utilisateur
Tannoy
Tannoy VLS SERIES Manuel utilisateur
Tannoy
Tannoy Reveal 501A Manuel utilisateur
Manuels Intervenants populaires d'autres marques
Bowers & Wilkins
Bowers & Wilkins 4 Manuel utilisateur
Sonance
Sonance SONOS OUTDOOR Series Manuel utilisateur
Electro-Voice
Electro-Voice EVID FM4.2 Manuel utilisateur
Pioneer
Pioneer XW-HTD630 Manuel utilisateur
Onn
Onn BWA16AA002 Manuel utilisateur
HP
HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur