"CONTINU" FUNCTION : 2 methods are possible.
1) "CONTINU" FOR AN UNDETERMINED NUMBER OF CYCLES
a) Press the CONTINU/STOP key. The display indicates CONTINU.
b) Press the key of the desired cycle. The cycles are carried out.
c) Press the cycle key again to stop at the end of the running cycle or the
CONTINU/STOP key to stop the cycle instantaneously.
2) "CONTINU" FOR A DEFINED NUMBER OF CYCLES
a) Press the CONTINU/STOP key. The display indicates CONTINU.
b) Press repeatedly the CONTINU/STOP key as many times as you wish to do
continuous cycles . The number is indicated on the display. To decrease the
displayed number, maintain the key pressed until you reach the desired value.
c) Select the desired key. The cycles will be carried out until the displayed number.
Note :
If an odd number is displayed and a 2-cup cycle has been selected, the machine will
stop at the penultimate cycle. The light of the corresponding 1-cup cycle will blink to
show you that you must press the key of the 1-cup cycle to do the number of cycle
previously defined.
"STOP" FUNCTION :
The CONTINU/STOP key allows the immediate stopping of any running cycle.
The start key of the cycle also allows also the immediate stopping of a simple cycle, or
the stopping at the end of the running cycle in the case of multiple cycles ("CONTINU"
function or parameter N>1)
B) MANUAL CYCLE SELECTION KEYS
This key allows you to make coffees from "ground coffee" which has been put manually
into the ground coffee trap :
a) Press the selection key "Manual cycles". The lights of the available keys blink in
orange.
b) When you open the trap, the lights stop blinking and remain orange.
c) Put in the ground coffee dose within 10 seconds and close the trap.
d) Choose and press a key with an orange light : the corresponding cycle will start.
Nota: to cancel a manual cycle, press the CONTINU/STOP key.
C) GRINDERS SELECTION KEY(according to the version and to the grinders preset)
Permits selection of the green or red grinder, the coffee keys will light up according to
the selection (red or green) and the cycle will use the selected grinder.
The modification of the grinders preset is possible only with the technician card.
nSTART UP
Only do this when the machine has been installed and, the connections and
adjustments have been carried out by a qualified installer. (Do not forget to open the
water tap feeding the machine ! )
I) TURNING THE MACHINE ON
Put the main On/Off switch on position 1. The display of the central box must be lit.
- If the display indicates "STOP", press the 0/1 key to switch on the machine.
- If the display indicates "NIGHT POSITION", press the Day/Night key to put the
machine in Day position. The filling of the boilers is carried out automatically, then the
heating starts.
•0/1 KEY:
Permits switching the machine on or off.
On position : All the lights of the keyboards are lighted and on the display of the
central box is displayed "UNIC TANGO" or "UNIC TANGO/S" according to the
configuration.
Off position : All the lights of the keyboards are extinguished and on the display of the
central box is displayed : "……..STOP……."
Caution: The machine is always on. To switch it off, put the main switch on 0.
‚DAY/NIGHT KEY :
Day position : in this position, the keys are activated and the lights lighted.
Night position : stand-by position, the machine is on a reduced temperature of 70°C.
The keys are not activated and all the lights of the keyboards are extinguished .
ƒKEY GIVING ACCESS TO THE CLEANING OPERATIONS
„KEY TO READ THE COUNTERS
F
COFFEES L. = 0008286
F
+
2
COFFEES R. = 0006199
F
+
2
COFFEES SUM = 0014485
…MENU KEY :
Permits access to the list of the main functions.
†and ‡+ / - KEYS
Permits access to each function and modification of the displayed values.
ˆPRO KEY:
Permits entry into programming mode on the desired key or function after selecting the
menu by the MENU key and then pressing +/-.
MEANING OF THE DISPLAY SYMBOLS
The display is composed of 2 lines. Generally, the upper line indicates the value of the
parameters, and the lower line gives some information on the mode of operation and the
actions to be carried out. Consequently, to carry out the reading or programming
sequences, you just have to follow the messages displayed on the lower line on the
display.
Display Meaning
> + / - Press ( + ) or ( - ) to change function on MENU, the pages of the functions, or
modify the blinking parameter .
> PRO 3 Press (PRO) for 3 seconds to select the displayed function.
> PRO Press (PRO) to select the parameter to be modified which starts blinking, or
to validate the blinking parameter and pass on to the following one.
> MENU Press (MENU) to leave the function, after validating it by (PRO).
> T Press a key of the right or left keyboard to make its parameters appear or to
configure it.
STEAM
HOT WATER
COFFEE CYCLE ( JUG )
MILK FOAM
HOT MILK
CONTINU / STOP SELECTION
FOR MANUAL CYCLES GRINDER
SELECTION
UNIT ELECTRONIC BOX
According to the equipment of your machine and the chosen keyboard version, some keys may not be present on your machine.
COFFEE CYCLE
( 1 AND 2 CUPS )
CAPPUCCINO CYCLE
( 1 AND 2 CUPS )
COFFEE + MILK CYCLE
( 1 AND 2 CUPS )
¦ELECTRONICBOXES
ELECTRONICCENTRAL BOX
Cup warmer .
Coffee hopper
Ground coffee trap .
Central electronic box
Door .
Keyboard 12 keys .
Main switch .
PTFEsteamoutlet .
Waste drawer
Telescopic
hot water outlet
Telescopic coffee outlet
- When the working temperatures are reached, the machine launches automatically some
initializing phases during which the display indicates Autocontrol 1 then Autocontrol 2.
These initializing phases are very important for the correct functioning of the machine.
These are possible only if the drawer is in its place, and they must not be stopped
especially not by removing the drawer.
When the buzzer stops sounding and the lights stops blinking, the machine is ready to
make coffee.
All the lights of the keys are lit and the display indicates : "UNIC TANGO"
II) USE OF THE COFFEE UNITS
On each unit, you can obtain up to 10 different programmable beverages (according to
the version)
1. Place the cup or cups under the telescopic coffee outlet after adjusting the height if
necessary according to the type of cups.
2. Press the choosen key after checking that the color of the light corresponds to the
grinder you wish to use.
3. During the cycle, the light of the key is blinking to indicate that the cycle is running.
The other "coffee" keys of the keyboard are extinguished and will be relit at the end
of the cycle.
4. You can start simultaneously another cycle on the other keyboard.
Notes:
For the hot water, steam, hot milk, milk foam… keys, the lights are green.
For the keys operating some "coffee" cycles, the color of the lights corresponds to the
selected grinder which is to be used for the next cycle:
RED: left grinder // ORANGE: ground coffee trap // GREEN: right grinder
III) WASTE DRAWER
According to the number of cups made and to the programmed capacity, a message on
the display indicates when it is necessary to empty your waste drawer. You can empty it
at any time or control its filling level. For that, you just have to:
1. Remove the drawer, the blue doors will move apart.
2. Empty the drawer or check its content
3. Put again the drawer back in its place and close the doors.
4. Validate by the key ( + ) during 3 seconds if you have emptied the drawer, and the
key ( - ) if you have not emptied the drawer.
Caution : if you have made a mistake during the validation, it is advised to take
out the drawer, to empty it if it is not empty and then validate it by pressing ( + )
for 3 seconds, after having put back the drawer.
