T&C TC36.NG05.C Manuel utilisateur

290409-12 TC36.NG05.C 5056.427.C45

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

These instructions are supplementary to the Installation and

Operating Instructions supplied with the replace and should be

kept together. Refer to the Installation and Operating Instructions

for proper gas supply, safety requirements and operating

instructions

TC36

HEARTWOOD

BURNER INSTALLATION

INSTRUCTIONS

PART#

TC36.NG05.C

FOR TC36 & TC36 AR

Series C

Contents of Package

TC36.NG05.C 290409-12

 • BURNERASSEMBLY(includingpilotandmanifold)

 • LOGGRATE 

 • TC36HEARTWOODLOGS

 • EMBERMATERIAL

 • HARDWAREPACKAGE

 • AIRDEFLECTOR

 • COALCHUNKS

 • VERMICULITE

If this replace is to be

used on Propane please

convert prior to installtion.

See pages 6 – 8.

TC36.NG05.C 290409-12

1. Attachtheburnerassemblytotheoor

shield in the bottom of the rebox with

twoscrews.Ensurethatthefrontedge

oftheburnerisushwiththefrontofthe

shield.

 (Fig.#1)

2. Attachsparkelectrode(ORANGE)and

sensor leads to the electrical bulk head.

(Fig.#2)(Thesparkelectrodeconnection

hasareddotaboveit).

3. Attachthepilotandgassupplytubes

to the bulk head tting and tighten.

(Fig.#3)Ensuretheconnectionsare

gas tight. Conceal the spark and sen-

sor wires below the supply tubes.

A panel set must now be installed.

See Installation and Operating

Instructions manual for details.

4. Positiontheslotsofthegratesecuring

bracketsovertheholesintheoorshield

and secure with the two screws.

 (Fig.#4)

Fig. # 2

Fig. # 1

Fig. # 4

Fig. # 3

Burner Installation

Note:

Ember material placement

and amount will affect

ame appearance.

More ember material

results in lower ame

height.

Add or remove as needed

until desired ame affect.

Reduce the amount used

on Propane models, as too

much will create soot

TC36.NG05.C 290409-12

Fig. #5

Ember Material

Fig. #6

Alargebagofembermaterialisshippedwiththereplaceandneedstobeinstalledon

theburnertoensureoptimumperformanceandameappearance.Abagofcoalchunks

and lava rock is also supplied this must only be used around the burner pan to cover up

the gas lines and brackets.

1. Pullapartthematerialintoembersizepieces(approximately1”squares)and

gentlyplacethemintotheburnerpan.Donotcompress,leavethemlooseforbest

performance.

2. Filltheburnerpanwithembersuntillevelwiththetopofthepanatrear,andgradually

slopeforwardtothereboxooratthefront,coveringbothburnertubes.

3. Placeremainingembermaterial,coalchunksandlavarockoutsideoftheburnerpan

as desired to cover-up gas lines and brackets. Do not put coal chunks or lava rock

inside burner pan as this will cause sooting and the burner to malfunction.

Embersonlyinthisarea.

Embers,coalchunksandlavarock.

TC36.NG05.C 290409-12

Fig. #9

Fig. #11 Fig. #12

Fig. #10

Fig. # 7

Gas plumbing and vent connections should be completed before proceeding.

Thelogsarefragile,andshouldbehandledwithcare.Unpackandinspectlogset.There

should be a total of seven logs.

Positionthelogsasindicatedbythefollowingpictures.Thesevenmainlogshaveholesand

/orpins.Engageeachpininthecorrespondingholes.Theremainingtwologsdonothave

holesorpins.Theyrestinposition.Locateasperthediagrams(g.#7-15)

Note: Improper placement of logs will cause sooting on internal parts and glass. The

logs may need to be repositioned slightly to avoid excessive ame impingement.

Log Placement

Fig. # 8

Fig. #14 Fig. #15

Fig. #13

BASE LOG, #1 LEFT CENTER LOG, #2 LEFT FRONT LOG, #3

LOG WITH HOLE, #4 RIGHT CENTER LOG, #5 FRONT RIGHT LOG, #6

CENTER TWIG, #8RIGHT BASE LOG, #7 CENTER BASE CHUNK, #9

Propane Conversion

If the unit is to be used on propane,

convert as follows using the compo-

nents supplied with this replace:

CAUTION

The gas supply and electrical power

must be shut off before proceeding

with the conversion.

Fig. # 17

Fig. # 18

Fig. # 16

WARNING

This conversion kit shall be

installed by a qualied

service agency in

accordance with the

manufacturer's instructions

and all applicable codes

and requirements of the

authority having

jurisdiction.

If the information in these

instructions is not followed

exactly, a re, explosion or

production of carbon

monoxide may result

causing property damage,

personal injury or loss of

life.

The qualied service

agency is responsible for

the proper installation of

this kit.

The installation is not

proper and complete un-

til the operation of the

converted appliance is

checked as specied in the

manufacturer's instructions

supplied with the kit.

Note:Factorysuppliedcomponentsmust

be used to ensure correct input.

Afterconversionconrmpropermanifold

pressure.

1. Ensuretheburner,pilotandgas

supply are turned off, and the

appliance has cooled.

2. Remove the two screws securing the

manifold assembly to the burner.

 (Fig.#16)

3. Remove the manifold assembly from the

burner.(Fig.#17)

4. Witha½”wrenchremovethenaturalgas

orice(#30)andreplacewithpropane

orice(#45)(ourpart#5021.34)

 (Fig.#18)

5. Fullyopentheprimaryairshutter.

6. Reinstall the manifold assembly and

 airdeector.

TC36.NG05.C 290409-12

Minimum

rate screw

7. Witha7/16”wrenchloosenthepilothead

on the pilot assembly by a half-turn

 (Fig.#19)

8. Slidethepilotadjustmentbandoverand

ensure that the hole in the orice band is

showing.(Fig.#20showsNGposition,

 Fig.#21showsLPposition)

9. Remove the minimum rate screw located

in the valve.

 (Fig.#22)

Fig. #21

Fig. # 22

Fig. # 19

Fig. # 20

TC36.NG05.C 290409-12

Minimum

rate screw

TC36.NG05.C 290409-12

Minimum

rate screw

NG LP

Fig #23

Fig #24

Fig #25

Fig #26

10. Replacetheminimumrate screwwiththe

one provided in the propane conversion

kitsuppliedwiththisreplace.Ensure

that the screw is fully installed.

 (Fig.#23)

11. Pullofftherubbercapfromthetopof

thepressureregulator.(Fig.#24)

12. Pressdownonthecenterpostand

rotate 90°. The center post should

 staydown.(Fig.#25).Replacethe

rubber cap.

13. Fill in the date and the name of the

person who performed the conversion

in the white area on the conversion

label. Peel off the protective backing

and apply the conversion label directly

over the gas specications on the rating

label.

14. Attachtheaccesspaneltothesideof

the rebox with the previously removed

screws.(Fig.#26)

Note:

Gasket must be installed with access

panel.

TC36.NG05.C 290409-12

1. Remove the plug from the manifold test

port. The plug is located between the

rightsidelintelandreboxside(bottom

port).(Fig.#27)

2. Thread the extension test tting into the

opentestport.(Fig.#28)

3. Attachapressuregaugeontothe

tting.

4. When testing is complete remove the

extension test tting and replace the

plug. Thread sealant will be required to

ensure a gas-tight connection.

Correct gas pressure requirement:

Supply Pressure Natural Gas Propane

(For purpose of input adjustment)

Minimum 5.0" WC 12.5" WC

Maximum 13.9" WC 13.9" WC

Manifold Pressure

Maximum 3.8" WC 11.0w" WC

Minimum 2.1" WC 5.5" WC

Note:To test the gas pressure, turn off the gas supply before removing the plug from

the supply pressure test port or manifold pressure test port.

Verify gas pressures with the replace lit and on the highest setting.

Fig #27

Fig #28

Gas Pressure Check

TC36.NG05.C 290409-12

Fig. # 29

The air shutter on the burner tube controls the primary combustion air to the gas burner

andispresetatthefactoryfornaturalgasfuel.Someadjustmentmaybenecessaryto

obtaindesiredameandtoeliminatecarbondeposits.Evaluateameappearanceafter

thereplacehasreachedoperatingtemperature.SeeFig.#29forproperamepattern.

Open primary air shutter if the logs, glass, and rebox have carbon accumulation and /

ortheamesarelong,darkandstringy.Theshuttermayalsobeopenedtoenhancethe

EmberMaterialglowandlessentheameheight.

Caution: Burner area may be hot!

Turn off the replace and allow the unit to cool before proceeding.

Caution: Proper air shutter setting is a

must.

Theameshouldbe just orange and“lazy”.

ItshouldNEVERbesettocreatesootingon

internal parts and glass.

Flame Adjustment

To Adjust:

1. Open and remove window frame and set

aside.See"WindowFrameRemoval"sec-

tion found in the Installation and Operating

Instructions manual.

2. Remove the log set and set aside.

3. LoosenthescrewinthePrimaryAirShut-

ter.

4. Rotate the shutter to increase or decrease

the amount of primary air.

5. Reassemble in reverse order.

Fig. # 31

PRIMARY AIR SHUTTER

Table des matières

Autres manuels T&C Brûleur

T&C

T&C TC42 Manuel utilisateur

T&C

T&C TC36.NG03 Manuel utilisateur

T&C

T&C TC30 Manuel utilisateur

T&C

T&C TC42 Manuel utilisateur

T&C

T&C TC36.NG03.C. Manuel utilisateur

T&C

T&C TC42.NG05.C Manuel utilisateur

T&C

T&C TC42 Manuel utilisateur

Manuels Brûleur populaires d'autres marques

Riello

Riello RS 28/M Guide de démarrage rapide

True Induction

True Induction TI4B Manuel utilisateur

Weishaupt

Weishaupt WG20 Series Manuel utilisateur

Carolina Cooker

Carolina Cooker M116672 Manuel utilisateur

Riello

Riello RX 500 S/PV Mode d’emploi

Unigas

Unigas HTP2000 Manuel utilisateur

baltur

baltur BT 250 DSG 4T Manuel utilisateur

muenkel design

muenkel design round burner Manuel utilisateur

Ecoflam

Ecoflam Multicalor 170.1 Manuel utilisateur

baltur

baltur BT 14 DSGW Manuel utilisateur

artisan

artisan Art-SB1 Mode d’emploi

Riello

Riello P 140 T/G Guide de démarrage rapide

AESYS

AESYS TurboFire II Manuel utilisateur

Riello

Riello RG1RKD Guide de démarrage rapide

IKEA

IKEA GRILLSKÄR Manuel utilisateur

RUSTA

RUSTA SAREK Manuel utilisateur

PROPOINT

PROPOINT 8933657 Manuel utilisateur

baltur

baltur TBL 1000 ME Manuel de référence