1.
1.1
●
●
●
1.2
●
●
●
1.3
●
●
●
●
●
●
2.
●
●
●
●
●
3.
●
●
●
●
●
●
●
●
●
●
●
4.
SAFETY GUIDELINES / DEFINE
WORK AREA
Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids,
gases, or dust. Power tools create sparks which may ignite the dust or fumes.
Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause
you to lose control. Protect others in the work area from debris such as chips and sparks. Provide
barriers or shields as needed.
ELECTRICAL SAFETY
Grounded tools must be plugged into an outlet properly installed and grounded in accordance with
all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not
use any adapter plugs. If the tools should electrically malfunction or break down, grounding provides
a low resistance path to carry electricity away from the user.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
Do not abuse the Power Cord. Never use the Power Cord to carry the tools or pull the Plug from an
outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving parts. Damaged Power
Cords increase the risk of electric shock.
PERSONAL SAFETY
Stay alert. Pay attention to the power tool when operating it. Do not use a power tool while tired or
under the influence of drugs, alcohol, or medication. A moment of inattention while operating power
tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure the Power Switch is off before plugging in.
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables
better control of the power tool in unexpected situations.
Always wear safety impact eye goggles and heavy work gloves when using the Polisher/Waxer.
Using personal safety devices reduce the risk for injury.
When waxing/polishing a vehicle, do not run the vehicle in an enclosed area. Carbon monoxide is a
colorless, odorless, vapor emitted from a vehicle’s running engine that may cause severe injury or
death if inhaled.
TOOL USE AND CARE
Do not force the tool. This tool will do the work better and safer at the speed and capacity for which
it was designed. Do not force the rotating Pad into the vehicle being waxed/polished. Apply moder-
ate pressure, allowing the Pad to rotate freely without being forced.
When using a hand-held power tool, always maintain a firm grip on the tool with both hands to resist
starting torque.
Always keep the extension cord away from moving parts on the tool.
Make sure the vehicle being waxed/polished is free from burrs and any other foreign matter which
could damage the tool.
Never leave the Polisher/Waxer unattended when it is plugged into an electrical outlet. Turn off the
tool, and unplug it from its electrical outlet before leaving.
OPERATING INSTRUCTIONS
Place a clean terry cloth Waxing Bonnet securely onto the Pad.
Prior to waxing/polishing a vehicle, make sure it’s surface has been thoroughly cleaned and is free
of dust, dirt, oil, grease, etc.
Apply about two tablespoons of wax (not included) evenly on the terry cloth Waxing Bonnet. Do not
apply the wax directly to the surface of the vehicle. The amount of wax needed will vary according to
the size of the vehicle being waxed. NOTE: Avoid using too much wax.
Grip the Polisher/Waxer firmly with both hands. Then turn the Power Switch to its “ON” position and
allow the Pad rotating at speed selector switch position 2-4.
Begin applying wax to the vehicle. Apply the wax to all flat surfaces with broad, sweeping strokes in
a criss-cross pattern. Apply the wax evenly over the surface of the vehicle, and add additional wax
as needed.
After the wax has been applied to the vehicle’s surface, turn the Power Switch to its “OFF” position.
Then unplug the Power Cord. Remove the Waxing Bonnet from the Pad. With the Waxing Bonnet in
your hand apply the wax to all hard to reach areas of the vehicle such as around lights, door handles,
under bumpers, etc.
Allow sufficient time for the wax to dry on the vehicle.
Place a clean Polishing Bonnet securely onto the Pad.
Grip the Polisher/Waxer firmly with both hands. Then turn the Power Switch to its “ON” position and
allow the Pad to rotate to its fullest speed(set the speed selector switch at position 5-6 ).
Begin polishing the vehicle by lightly buffing off the wax residue in a circular pattern. Continue polish-
ing until all the wax residue is removed.
After the wax has been removed from the vehicle’s surface, turn the Power Switch to its “OFF”
position. Then unplug the Power Cord. Remove the Polishing Bonnet from the Pad. With the Polish-
ing Bonnet in your hand, remove the wax from all hard to reach areas of the vehicle such as around
lights, door handles, under bumpers, etc.
SPECIFICATIONS
EN
