System air F-C2 Manuel utilisateur
F-C2
Cartridge Fire Damper
Handbook
2/33 | F-C2
Table of Contents
Overview .........................................................3
Technical Parameters ..................................................5
Diagrams .........................................................8
Dimensions ........................................................10
Ordering Code ......................................................11
Installation ........................................................12
Electrical Parameters ...................................................30
Operation Manual ....................................................31
3/33 | F-C2
Description
Fire dampers represent passive fire protection, designed with the help of compartmentalization to prevent the spread
of toxic gases, smoke and fire. Standard fire dampers are designed and certified in accordance with EN 15650 and
tested for EIS criteria according to EN 1366–2. Fire damper together with its installation form an inseparable part of fire
resistivity rating. F-C2 fire dampers are designed for the installations listed and described in their HandBook.
By default, F-C2 fire dampers are only supplied with spring loaded activation, optionally with micro switch. In case of
fire, the fire damper closes automatically when the temperature of the air in the duct reaches 72°C. The F-C2 damper
closes after the melting of the thermal fuse. After the closing of the damper blade, it is mechanically locked in the
closed position and can only be opened manually, which requires access of the maintenance staff into the duct. To
improve the accessibility for inspection of the fire damper a flexible duct coupling can be used.
Highlights
• Performance up to 2 hours
• One product fits several resistivities
• Closed state detection
• Installation with valves
Product Types
• F-C2 with size range from 80 mm up to 125 mm:
Cartridge fire damper with sheet metal blades.
• F-C2 with size range from 140 mm up to 200 mm:
Cartridge fire damper with calcium-silicate blades.
Design
F-C2 dampers have powder coated casings made from galvanized sheet metal. Blades from non-asbestos insulants
and an intumescent seal, that expands in a fire situation.
Activation Types
•H0
Fire damper with a spring loaded blades with release by a thermal fuse link set to 72 °C.
•H1
Fire damper with a spring loaded blades with release by a thermal fuse link set to 72 °C + closed indication with an AC/
DC 24 V contact switch on one blade.
4/33 | F-C2
Material Composition
The product contains galvanized sheet metal, graphite fire-proof laminate, polyurethane foam. These are processed in
accordance with local regulations. The product contains no hazardous substances, except for the solder in the
thermofuse, which contains a milligram of lead. Calcium silicate board is used in sizes greater than 125 mm.
List of installation Accessories
• CBR-C2: Set of 4 cover boards mandatory for dry installation of F-C2
• FCR-C2: Flexible duct connection for F-C2 accessibility
Detailed information about other accessories is available in SystemairDESIGN in fire damper accessories section.
5/33 | F-C2
Technical Parameters
Durability test
50 cycles with no change of the required properties
Fire testing pressure
Under-pressure up to 300 Pa
Safety position
Closed - In fire scenario the damper closes via spring between blades
Airflow direction
Both directions
Allowed air velocity
Damper can still operate at max. 6 m/s. Air without any mechanical or chemical contamination
Side with fire protection
Depending on installation classification: From both sides (i <-> o)
Repeated opening
Not possible. Only manual loading of the spring is required when installing. It is not possible to load the spring after
reaching activation temperature.
Activation Temperature
72 °C
Operational temperature
• Minimum: 0 °C
• Maximum: 60 °C for 72 °C thermal fuse link
Environment suitability
Protected against weather disruptions, with temperature above 0 °C, up to 95% Rha, (3K5 according to EN 60721-3-3)
Open/Closed indication
Closed indication of one blade side with micro-switch - Activation type H1
Closing/Opening time
Approximately 1 second
Inspection possibility
By accessing through accessory FCR-C2. Or after removal of valve, when installed with valve on one or both sides.
Maintenance
Not required. Dry cleaning if demanded by law in the country in which the dampers are installed.
Revisions
Determined by law in the country in which the fire dampers are installed. It is recommended to perform visual
inspection at least every 12 months.
Allowed pressure
300 Pa
Tightness of the housing (EN 1751)
Damper is placed within duct, that means the tightness class is equal to duct tightness.
6/33 | F-C2
Transport and Storage
Dry indoor conditions with a temperature range of -20 °C to +50 °C. The damper blade is transported in closed
position.
Product parts
The F-C2 packaging also includes additional product label, that must be attached to the duct next to wall where the F-
C2 fire damper is installed.
P8
P3
P2
P9
P7
P5
P6
P4
P1
P8
P3
P2
P9
P5
P6
P4
P1
P10
P10
DN140 ... DN200DN80 ... DN125
Note:
Cartridge fire damper F-C2 made with sheet-metal blades, size range from 80 mm up to 125 mm (left)
Cartridge fire damper F-C2 made with calcium silicate blades, size range from 140 mm up to 200 mm (right)
Legend:
P1 Casing
P2 Blades
P3 Thermal fuse link
P4 Blades spring
P5 Detent spring
P6 External peripheral sealing
P7 Internal peripheral sealings
P8 Blade surface foams
P9 Microswitch 24 V AC/DC
P10 Product label
7/33 | F-C2
Assessed Performance of F-C2
20 CE 1396
Systemair Production a.s.
Hlavná 371, 900 43 Kalinkovo, Slovakia
1396-CPR-0183, F-C2
EN 15650 : 2010
Circular fire dampers
Nominal activation conditions/sensitivity - Pass
• sensing element load bearing capacity
• sensing element response temperature
Response delay (response time) - Pass
• closure time
Operational reliability - Pass
• manual cycle = 50 cycles
Fire resistance:
Resistivity depending on installation method and situation
• integrity E
• maintenance of the cross section (under E)
• mechanical stability (under E)
• cross section (under E)
• insulation I
• smoke leakage S
Durability of response delay - Pass
• sensing element response temperature and load bearing capacity
Durability of operational reliability - NPD
• open and closing cycle
8/33 | F-C2
Diagrams
Accessory CBR-C2 and fire resistance class (EI60S, EI90S and EI120S) do not affect the pressure drop and A-weighted
total discharged sound power level.
The pressure drop and A-weighted total discharged sound power level depend on the nominal diameter of the F-C2
and air flow volume at different duct pressures.
F-C2-...-H0
Pressure drop & A-weighted sound power level in dB(A)
50 80 100 m³/h
20 30 40 l/s
20
30
50
Pa
Size: 80 Size: 90
Size: 95
25
30
35
40
45
25
30
35
40
45
25
30
35
40
45
F-C2-...-H1
Pressure drop & A-weighted sound power level in dB(A)
50 80 100 m³/h
20 30 40 l/s
20
30
50
Pa
Size: 80 Size: 90
Size: 95
30
35
40
45
25
30
35
40
45
25
30
35
40
45
F-C2-...-H0
Pressure drop & A-weighted sound power level in dB(A)
100 200 300
m³/h
30 50 80 l/s
10
20
50
Pa
Size: 100
Size: 110
Size: 120
25
30
35
40
45
25
30
35
40
45
25
30
35
40
45
F-C2-...-H1
Pressure drop & A-weighted sound power level in dB(A)
100 200 300
m³/h
30 50 80 l/s
10
20
50
Pa
Size: 100
Size: 110 Size: 120
25
30
35
40
45
25
30
35
40
45
25
30
35
40
45
9/33 | F-C2
F-C2-...-H0
Pressure drop & A-weighted sound power level in dB(A)
200 300 500
m³/h
50 80 100 l/s
10
20
50
Pa
Size: 125
Size: 140
Size: 150
25
30
35
40
45
25
30
35
40
45
25
30
35
40
45
F-C2-...-H1
Pressure drop & A-weighted sound power level in dB(A)
100 200 300 m³/h
30 50 100 l/s
5
10
50
Pa
Size: 125
Size: 140
Size: 150
25
30
35
40
45
25
30
35
40
45
25
30
35
40
45
F-C2-...-H0
Pressure drop & A-weighted sound power level in dB(A)
200 300 500 m³/h
50 100 200 l/s
5
10
20
Pa
Size: 160
Size: 180Size: 200
25
30
35
40
45
25
30
35
40
45
25
30
35
40
45
F-C2-...-H1
Pressure drop & A-weighted sound power level in dB(A)
200 300 500 m³/h
50 100 200 l/s
5
10
20
Pa
Size: 160
Size: 180
Size: 200
25
30
35
40
45
25
30
35
40
45
25
30
35
40
45
Legend:
ps (Pa) - Pressure drop
qv (m3^/h), (l/s) - Air flow volume
±Δ (%) - Deviation from measured value
Lwa (dB(A)) - A-weighted total sound power level
v (m/s) - Air face velocity
10/33 | F-C2
Dimensions & Weights
Dimensions
DN-1,5
60
R1
DN-1,5
60
R1
DN140 ... DN200DN80 ... DN125 (mm)
Overhangs
R1(mm)
DN (mm)
80 90 95 100 110 120 125 140 150 160 180 200
8,8 13,8 16,3 18,8 23,8 28,8 31,3 47,0 52,0 57,0 67,0 77,0
Weights
m (kg)
DN (mm)
80 90 95 100 110 120 125 140 150 160 180 200
0,20 0,23 0,25 0,26 0,30 0,34 0,36 0,50 0,60 0,60 0,70 0,90
Free area
Av(m2)
DN (mm)
80 90 95 100 110 120 125 140 150 160 180 200
0,003 0,004 0,005 0,006 0,007 0,009 0,010 0,010 0,012 0,014 0,018 0,023
Table des matières
Autres manuels System air Clapet coupe-feu et pare-fumée
System air
System air S-SA2 Manuel utilisateur
System air
System air PKIR-E60S Manuel
System air
System air PK-I-R-EI60S Manuel utilisateur
System air
System air fantech Pro 150 Manuel
System air
System air A-FDR-3G-OF Manuel utilisateur
System air
System air F-R60 Manuel utilisateur
System air
System air S-RA1 Series Manuel utilisateur
System air
System air S-BA2 Manuel utilisateur
System air
System air IMOS-RK Manuel d'utilisation et d'entretien
System air
System air F-B90 Manuel utilisateur
System air
System air OCWATERLOO PKIR3G Instructions d'installation
System air
System air SAVE VTC 700 Mode d’emploi
System air
System air F-B90 Manuel utilisateur
System air
System air S-SA2L Manuel utilisateur
System air
System air S-SA1 Manuel utilisateur
System air
System air FDS-3G EX Series Manuel utilisateur
System air
System air FDR-3G KR Series Manuel utilisateur
System air
System air fantech bathfan Select SC50-80-110 Manuel utilisateur
System air
System air FDS-3G OF Series Manuel utilisateur
System air
System air MA multi Manuel utilisateur
