Synthes DHS Manuel utilisateur
Original Instruments and Implants of the
Association for the Study of Internal Fixation –
AO/ASIF
DHS/DCS Standard System
Surgical Technique
SYNTHES 1
Implants 2
Indications/Contraindications 4
DHS®Plate 6
DHS®Trochanter Stabilizing Plate 11
DCS®Plate 95° 12
Assembling the insertion instruments 17
Implant removal 18
Bibliography 19
DHS/DCS Standard System
Table of contents
Image intensifier control
Warning
This description is not sufficient for immediate application
of the instrumentation. Instruction by a surgeon experienced
in handling this instrumentation is highly recommended.
2
DHS/DCS Standard System
Implants
DHS Trochanter Stabilizing Plates (281.869/870)
The DHS trochanter stabilizing plates offer anchoring
options for the fixation of fragments of the greater trochanter
(a), an aperture for an anti-rotation screw (b), an oval
aperture for the DHS/DCS screw (c) and holes for fixation to
the DHS plate (d). The scooped section can be adapted
to the anatomical contours of the greater trochanter using
bending irons or flat-nosed pliers.
–for use with DHS plates
–Steel
–Short: 138 mm
–Long: 148 mm
b
a
a
a
a
c
d
d
d
d
d
d
c
b
DHS®Plates 130°–150° (281.040–560)
–Steel
–Fixation with cortex screws 4.5 mm
–Lengths: 43–270 mm (2–16 holes)
–Thickness: 5.8 mm
–Width: 19 mm
–Hole spacing: 16 mm
–Barrel lengths: 25–38 mm
Anti-rotation screw
The anti-rotation screw can be used on its own, with the
DHS plate, or the DHS plate and the DHS trochanter
stabilizing plate. The screw effectively prevents rotation of
the head-neck fragment of the femur around the DHS
screw.
–Cancellous bone screw 6.5 mm, steel (214.814–910)
–Cannulated screw 7.0 or 7.3 mm, steel
SYNTHES 3
DHS Locking Device (280.960)
The DHS locking device is used together with the
DHS for temporary locking of the sliding mechanism of
the DHS/DCS screw.
–Steel
–Inner hexagon for DHS Torque-indicating Screwdriver
338.560
–Length: 35 mm
DCS Plates (281.900–990)
–Steel
–Fixation with cortex screws 4.5 mm
–Lengths: 114–370 mm (6–22 holes)
–Thickness: 5.4 mm
–Width: 16 mm
–Hole spacing: 16 mm
–Barrel length: 25 mm
DHS/DCS Screws (280.000–950)
–Steel
–Lengths: 50–145 mm
–Thread diameter: 12.5 mm
–Thread length: 22 mm
–Shaft diameter: 8.0 mm
DHS/DCS Compression Screw (280.990)
The compression screw is used together with the DHS
and DCS plates.
It is used in pertrochanteric fractures to compress
the femoral fragments on the proximal and distal sides of
the fracture.
The DHS/DCS compression screw must be used if a DCS
plate is applied to the distal femur.
–Steel
–Inner hexagon for Hexagonal Screwdriver 314.120 and
314.270
–Length: 36 mm
4
Indications for DHS plates
–Pertrochanteric and intertrochanteric fractures of type
31-A in the AO/ASIF classification.
For highly unstable types of fracture, additional implants
such as the DHS trochanter stabilizing plate or DHS locking
device may be required.
–Femoral neck fractures 31-B2/B3, in conjunction with
the use of an anti-rotation screw.
Indications for DHS trochanter stabilizing plates
–Group 31-A2 and A3 fractures, particularly multifragment
fractures.
The DHS Trochanter Stabilizing Plates (281.869 and
281.870) are viewed as an extension of the DHS plate for
stabilizing the greater trochanter and for accepting
an anti-rotation screw.
Where telescoping is present in the fracture zone, the
combination of a DHS plate and a DHS trochanter stabilizing
plate prevents the tendency of the trochanter fragments
to move laterally with consequent medialization of the shaft
in relation to the head-neck fragment. Additionally,
a rotationally unstable head-neck fragment can be stabilized
by inserting an anti-rotation screw cranially and parallel
to the DHS/DCS screw.
DHS trochanter stabilizing plates can also be used to
secure splintered greater trochanter fragments and stabilize
them by using screws or cerclage wires in the scooped
section of the DHS trochanter stabilizing plate.
DHS/DCS Standard System
Indications/Contraindications
SYNTHES 5
Indications for DCS plates
–Proximal femur: very proximally located, purely sub-
trochanteric fractures of types 32-A 1.1, A 2.1, A 3.1;
32-B 1.1, B 2.1, B.3.1.
–Fractures of type 33-A (extra-articular, supracondylar fractures
of the distal femur)
–Fractures of type 33-C1/C2/C3 (fully articular fractures
of the distal femur)
Contraindications for DCS plates
–Pertrochanteric fractures or trochanteric fractures extending
to the subtrochanter.
Indications for the DHS locking device
The locking device is used if there is a risk of severe
shortening of the femoral neck due to telescoping of
the head fragment.
–Group A 2 and A 3 fractures in young patients, particularly
fractures with a comminuted zone.
A 2.2 With several intermediate fragments
A 2.3 Fracture extending more than 1 cm below the
lesser trochanter
A 3.3 Multifragment fractures
Contraindication for locking device
–Osteoporotic bone
6
1
Position patient
Place the patient in a supine position on the operating table.
2
Reduce fracture
If possible reduce the fracture while closed under the
image intensifier.
If an operating table without extension is used, reduce
the fracture by flexion, lengthwise traction, abduction and
internal rotation. Fix the fracture temporarily with Kirschner
wires. Position the Kirschner wires so that they do not
hamper insertion of the DHS/DCS screw and DHS plate.
3
Access
The proximal femur is approached laterally. Make a
15–20 cm straight incision starting two fingerwidths proximal
to the greater trochanter.
Split the iliotibial tract lengthwise. Detach the M. vastus
lateralis dorsally from the intermuscular membrane, retract
ventrally and, if necessary, make a slight notch in the
muscle in the region of the innominate tubercle. Expose the
proximal femoral shaft without retracting the periosteum.
4
Determine antetorsion
To determine the antetorsion of the femoral neck using the
DHS Angled Guide (358.005–040) and the DHS/DCS T-Handle
(338.080), place a Kirschner wire ventrally over the femoral
neck and tap the tip slightly into the femoral head.
DHS/DCS Standard System
DHS plate
SYNTHES 7
5
Determine entry point for the DHS/DCS screw and
insert guide wire
Implants with CCD angles from 130° to 150° are available.
Depending on the angle of the implant, the entry point
for the DHS/DCS screw is approx. 2.5 – 6.0 cm distal to the
innominate tubercle.
Locate the DHS angled guide and drill the outer cortex
using the Drill Bit 2.0 mm (310.190). Insert the DHS/DCS
Guide Wire with Threaded Tip 2.5 mm (338.000) until
the tip reaches the subchondral part of the femur head.
The guide wire runs approximately 6 mm proximal to
Adams’ arc in the dorsocaudal quadrant of the femoral head.
The thread on the tip of the guide wire stops the wire
from being pulled out. Check the position of the guide wire
under the image intensifier in the a.p. view and the
Lauenstein position. If an extension table is used, record
an axial view.
Note: Leave the guide wire in the femur until the plate is
fitted (step 9, page 9). If the guide wire is not correctly
positioned it must be reinserted. Once the DHS/DCS screw is
inserted in an incorrect position, no subsequent correction
is possible.
6
Measure the length of the guide wire
Slide the DHS/DCS Direct Measuring Device (338.050)
over the guide wire and measure the length of the guide wire
in the bone (e.g. 120 mm).
Remove the antetorsion Kirschner wire.
ventral
caudal
cranial
dorsal
8
7
Reaming
Assemble the DHS triple reamer: Slide the DHS Reamer
(338.110 or 338.440) over the Drill Bit 8.0 mm (338.100)
until it clicks into place at the selected mark (in this
example at 110 mm). The reaming depth can be adjusted
in 5 mm increments. Secure the reamer by tightening
the Knurled Nut (338.120).
Adjust the reaming depth on the DHS Triple Reamer
(338.130). The appropriate reaming depth is 10 mm less than
the measured length of the guide wire (in this example
120 mm – 10 mm = 110 mm).
Ream the screw channel until the tip of the reamer is 10 mm
in the subchondral part of the femoral head.
The length of the appropriate DHS/DCS screw is identical
to the reaming depth (in this example 110 mm).
Notes: While reaming, ensure that the guide wire
does not bend. Bending the guide wire can result in incorrect
placement of the DHS plate and DHS/DCS screw.
If the guide wire is pulled out during reaming it must be
replaced. Push the short DHS Centering Sleeve (338.180) into
the drill hole and insert a DHS/DCS screw with the shaft
foremost into the centering sleeve. The guide wire can now
easily be reinserted back in its original position.
Remove the DHS triple reamer.
Option
In case of hard bone, tap the thread using the DHS/DCS
Tap (388.170) and the short DHS/DCS Centering Sleeve
388.180). Tap the thread until the selected depth in the small
window of the centering sleeve reaches the lateral cortex
(in this example 100 mm).
Note: The DHS/DCS tap may not be used in osteoporotic
bone.
SYNTHES 9
8
Insert the DHS/DCS screw
Slide the insertion instruments (see page 17 for assembly)
over the guide wire and advance the long Centering Sleeve
(388.190) into the drilled hole. Insert the DHS/DCS screw
(in this example 110 mm) until the zero mark reaches
the lateral cortex. Continue inserting the screw for a further
5 mm if the bone is osteoporotic.
The handle of the DHS/DCS Wrench (338.060) must
remain parallel to the femoral axis since only in this screw
position can the DHS plate be positioned correctly
over the flat-sided shaft of the DHS/DCS screw against
the femoral shaft.
Note: Do not use the DHS/DCS wrench to reduce the
fracture as this only allows limited transmission of forces.
Remove the DHS/DCS wrench and the long centering sleeve.
9
Position DHS plate
Position the DHS plate over the short Connecting Screw
(338.200) against the femoral shaft. Loosen the connecting
screw and remove the Guide Shaft (338.210).
Set the power tool to reverse operation to remove the guide
wire. Dispose of the guide wire.
10
Tap DHS plate
Tap the DHS plate into the predrilled channel using
the DHS/DCS Impactor (388.140). Compress the fracture by
gentle hammer taps against the impactor.
Option
Where a Trochanter Stabilizing Plate (281.869 or 281.870)
is indicated, perform steps 11b–13b on page 11.
DHS/DCS Standard System
DHS plate
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Synthes Équipement médical
Synthes
Synthes UNIUM Manuel utilisateur
Synthes
Synthes Expert Tibial Nail Manuel utilisateur
Synthes
Synthes TFN Manuel utilisateur
Synthes
Synthes Synex System Manuel utilisateur
Synthes
Synthes Hybrid Fixator Proximal Tibia Frame Manuel utilisateur
Synthes
Synthes LCP Distal Humerus Plates Manuel utilisateur
Synthes
Synthes TRS Manuel utilisateur
Synthes
Synthes The Titanium Femoral Nail System Manuel utilisateur
Synthes
Synthes USS Low Profile Manuel utilisateur
Synthes
Synthes SYNMESH Manuel utilisateur
Synthes
Synthes ComPact Air Drive II Manuel utilisateur
Synthes
Synthes USS II Manuel utilisateur
Synthes
Synthes Electric pen drive Guide de configuration
Synthes
Synthes USS Universal Manuel utilisateur
Synthes
Synthes Small Battery Drive II Manuel utilisateur
Synthes
Synthes Spine Cable System Guide de démarrage rapide
Synthes
Synthes LUPINE BR Anchor Manuel utilisateur
Synthes
Synthes DFN Manuel utilisateur
Synthes
Synthes LCP Manuel utilisateur
Synthes
Synthes LISS DF Manuel utilisateur
