Syco RS-401 Mode d’emploi
Start and manual operation
Syco RS-401
Dual SIM / LTE
System: Android ™ 8
PLADEN
2
DESCRIPTION OF THE PHONE
NAME
SHORT DESCRIPTION
1HEADPHONE
CONNECTION
Audio headset
connection
2 USB-OUTPUT
Charge the device,
connect to PC or OTG
USB
3 SPEAKER
A speaker that is used
during a call
3
4 CAMERA FRONT
Application: mainly
selfie (5 Mpix)
5 SCREEN
It is used to display its
content and operation
by touch
6 HYBRID LOCK
FOR SM AND SD
CARDS SIM
Card slot and SD
memory card (SIM2
interchangeable with
SD)
7 EXTRNAL
LOUDSPEAKER
Supports the emission
of external sounds
8 VOLUME KEY
Increase/ decrease the
volume level
9 BUTTON
ON/OFF
Switches the device on
and off, lock and
unlocks the screen
4
10 CAMERA BACK
SIDE
The camera of the
main unit (13 Mpix)
11 FLASH
Flash mode when
taking pictures, flash
light function
12 CAMERA
BUTTON
The physical key for
taking pictures
13 RETURN KEY
Return to the previous
screen and close the
application
14 MAIN BUTTON
Return to the main
screen from any menu
15 SWITCH
BUTTON
Button to switch
between active
applications
16 LED
Notification light
5
CARD INSTALLATION: SIM 1, SIM 2 en
MICRO SD
The SIM card slot and an SD memory card are
located on the left side of the device. To
install the cards, first remove the protective
rubber and then gently pull on the metal
frame.
(you can do this with the aid of tweezers):
Before you start installing the cards, make
sure that the phone is switched off and not
connected to the adapter or other
accessories.
6
Place the frame on a flat surface and
install the cards as shown in the image
below:
or
Carefully slide the frame back into the
device with the installed cards.
micro SD nano SIM
nano SIM1 nano SIM2
7
After switching on, the phone must
automatically recognize the cards. Note: the
hybrid slot works according to the following
principle: two SIM cards or one SIM card and
one micro SD card.
Be careful when using a memory card, especially
during insertion and removal. Some memory
cards must be formatted with a computer
before the first use. Back up regularly your of
information when using SD cards! Use outside of
the rules or other factors can cause damage to
or loss of the contents of the cards.
PRECAUTIONS DURING CARD
INSTALLATION
Switch the phone off and wait a few
seconds before inserting or removing the SIM
card (s). Take care of the SIM card (SD), do not
bend or scratch it.
When the SIM card is inserted or
damaged, a message appears on the screen
when the phone is switched on to indicate that
there is no card in the given slot. Check that the
card is correctly inserted and not damaged, and
then turn on the phone again. If the device still
does not detect the card, you must provide it to
the network operator of your GSM network for
replacement.
8
When it comes to the situation that the
SIM card is blocked, do not hesitate to ask
for help via our website.
All mechanical damage to SIM (SD)
connections are not subject to warranty
repairs.
INSTALLATION BATTERY
The Syco RS-401 has a permanently
installed battery in the housing of the
device.
In the event of damage to the battery,
send the entire device to an authorized Syco
service center. Attempts to remove the
battery by an unauthorized service or
person are treated as equivalent to the loss
of the warranty.
To reset the device (this corresponds to
the temporary removal of the battery),
press and hold the ON / OFF BUTTON (about
10 seconds). (9). The device loses power for
a moment and then automatically restarts.
CHARGE THE BATTERY
Never use a charger or battery that is not
from the manufacturer or damaged. Other
types or modifications may damage the
phone and void the warranty.
9
When the battery reaches 15% of the charge, a
message appears indicating that the battery
needs to be charged. To charge the battery,
connect the charger to the wall socket and to
the telephone.
Please note that incorrect connection of the
charging plug (eg opposite) to the USB
connection can cause serious damage to the
device, but is not covered by the warranty.
When using chargers from other manufacturers,
make sure that the charger has a micro USB
plug.
The battery symbol on the display () indicates
the charge level of the battery. It takes about
3-4 hours to fully charge the battery. While
charging, you can use the device, but this
extends the charging time. It is normal for the
device to warm up.
Attention!
The ambient temperature during charging
must be between 0 °C and + 40 °C.
Batteries will wear after a certain time, which
means that their charging time will be shorter
and shorter.
10
SAVING THE BATTERY ENERGIE
(INTELLIGENT ENERGIE SAVING)
The device offers options to help you save
battery power. By changing these options and
disabling functions that are running in the
background, you can extend the operating
time of the device:
Every time you do not use the device,
you put it into sleep mode,
Close unnecessary applications,
Turn off Bluetooth,
Turn off Wi-Fi,
Decrease the backlight time,
Reduce the brightness of the screen.
SWITCH THE DEVICE ON/OFF
Press and hold the BUTTON for a few
seconds. / Switch off the telephone (9) to
switch the device on or off. When you switch
on the device for the first time, configure the
device by following the on-screen
instructions. The first step is to configure the
internet connection (using WiFi or
transmission and data) of the Google accounts
(Gmail).
Pay attention!
To be able to download apps from the "Play
Store", the Google Account must be
configured.
Table des matières
