Swedstyle Memory T Manuel utilisateur

1 Swedstyle Memory T Swedstyle Memory T 1

/ MEMORY T 1.0

MANUAL

Document Version 2.0 / October 2019

TOUCHfamily

Valid for:

• TOUCHfx

• TOUCHdown

• TOUCHinlay

Swedstyle Memory T

Operating manual

Swedstyle Memory T 3

CONTENTS

1 General information........................................................................ 4

2. Safety........................................................................................................ 4

2.1 General safety regulations..................................................... 4

2.2 Intended use............................................................................... 4

2.3 Reasonably foreseeable misuse............................................ 4

2.4 Liability .........................................................................................5

2.5 Residual risks ..............................................................................5

3 The product............................................................................................6

3.1 Key product features ............................................................... 6

3.2 Dimensions................................................................................. 7

4 Assembly.................................................................................................7

4.1 Required components ............................................................. 9

4.2 Process.......................................................................................... 9

4.3 Completing assembly............................................................... 9

5 OPERATION .......................................................................................10

5.1 Adjusting the table top height .............................................11

5.2 Saving a memory position.....................................................11

5.3 Adjusting the table to a memory position........................11

5.4 Key lock...................................................................................... 12

5.5 Locked handset........................................................................ 13

6 ADDITIONAL INFORMATION............................................... 13

6.1 Disassembly.............................................................................. 13

6.2 Maintenance ............................................................................ 13

6.3 Cleaning..................................................................................... 14

6.4 Replacing a handset............................................................... 14

6.5 Troubleshooting...................................................................... 14

6.6 Disposal...................................................................................... 14

4 Swedstyle Memory T Swedstyle Memory T 5

1 GENERAL INFORMATION

Assembly personnel must read all documentation before starting assembly. Keep all

documentation for as long as the product is in your possession. Ensure that all documentation

is provided to subsequent owners. This Manual may change without notice. The most recent

version is available on our website.

2. SAFETY

Handsets may only be installed by Skilled Persons. A Skilled Person is deﬁned as someone who:

• Is authorized for installation planning, installation, commissioning,

or servicing of the product

• Has read and understood all documentation relevant to the Handset

• Has the technical education, training, and/or experience to perceive risks and avoid hazards

• Has knowledge of the specialist standards applicable to the product

• Has the expertise to test, assess, and manage electrical and mechatronic products and

systems in accordance with the generally accepted standards and guidelines of electrical

engineering and furniture manufacturing

2.1 General safety regulations

In general, the followng safety regulations and obligations apply when handling the product:

• Do not operate the product unless it is in a clean and perfect condition

• Do not remove, change, bridge, or bypass any protection, safety, or monitoring equipment

• Do not convert or modify any components

• In the event of malfunction or damage, faulty components must be replaced immediately

• Unauthorized repairs are prohibited

• Do not attempt to replace hardware unless the product is in a de-energized state

• Only Skilled Persons are allowed to work with ”Memory T” hand controller

• Ensure that national worker protection conditions and national safety and accident

prevention regulations are observed during operation of the system

2.2 Intended use

This product is a Handsets for electrically Height-Adjustable Tables. It is used to control

Height-Adjustable Table systems via a Control Box. It is intended for indoor use only.

It may only be installed in compatible Height-Adjustable Tables and with Swedstyle-approved

accessories. Use beyond or outside the intended use will void the product’s warranty.

2.3 Reasonably foreseeable misuse

Usage outside of the intended use may lead to minor injury, serious injury, or even death.

Reasonably foreseeable misuse of the Handset includes, but does not extend to:

• Connecting unauthorized parts to the product. If you are unsure as to whether a part can

be used with a Handset, contact Swedstyle for further information

2.4 Liability

Swedstyle products comply with all currently applicable health and safety regulations.

However, risk can result from incorrect operation or misuse. Swedstyle is not liable for damage

or injury caused by:

• Improper product use

• Disregard of the documentation

• Unauthorized product alterations

• Improper work on and with the product

• Operation of damaged products

• Wear parts

• Improperly performed repairs

• Unauthorized changes to the operating parameters

• Disasters, external inﬂuence, and force majeure

The information in this Operating Manual describes the characteristics of products without

assurances. Resellers assume responsibility for the Swedstyle products installed in their

applications. They must ensure their product complies with all relevant directives, standards,

and laws. Swedstyle shall not be held liable for any damage that is directly or indirectly caused

by the delivery or use of this document. Resellers must observe the relevant safety standards

and guidelines for each product in the Table System.

2.5 Residual risks

Residual risks are the risks that remain after all relevant safety standards have been complied

with. These have been evaluated in the form of a risk assessment. Residual risks associated with

the installation of the hand controller are listed here and throughout this Operating Manual.

WARNING. Risk of death or serious injury through electric shocks

Hand controllers are electrical devices. Although you will not have to connect the Handset to

the Control Box during assembly, basic safety precautions must be taken at all times. Failure to

observe electrical safety precautions may lead to death or serious injury through electric shocks.

• Never open the Handset

• Ensure that the Handset is not connected to the Control Box during assembly

• Do not convert or modify the Handset in any way

• Do not immerse the Handset or its components in liquid. Clean only with a dry

or slightly damp cloth

• Do not place the Cable of the Handset on heated surfaces

• Check the housing and cables of the Handset for visible damage. Do not install

or operate damaged products.

6 Swedstyle Memory T Swedstyle Memory T 7

WARNING. Risk of death or serious injury in explosive atmospheres

Operating the Handset in potentially explosive atmospheres may lead to death or serious injury

through explosions.

• Read the relevant directives to determine if an atmosphere is potentially explosive

• Do not operate the Handset in potentially explosive atmospheres

CAUTION. Risk of minor or moderate injury through tripping

During the assembly process, you may have to step over Cables. Tripping over Cables may lead

to minor or moderate injury.

• Ensure that the assembly area is kept clear of unnecessary obstructions

• Be careful not to trip over Cables

CAUTION. Risk of minor or moderate injury through crushing

If any Handset Key becomes stuck while the system is in motion, the system may not stop

properly. This may lead to minor or moderate injury through crushing.

• Disconnect the system immediately if any Handset Key becomes stuck

3 THE PRODUCT

3.1 Key product features

3.2 Dimensions

Length 85.9 mm

Width 132.5 mm

Height (to underside of Table Top) 32.8 mm

4 ASSEMBLY

CAUTION. Risk of minor or moderate injury through improper handling

Improper handling of the product during assembly may lead to minor or moderate injury

through cutting, pinching, and crushing.

• Avoid contact with sharp edges

• Be careful while handling tools that may cause personal injury

• Ensure assembly complies with the generally accepted standards and guidelines of

electrical engineering and furniture manufacturing

• Read all instructions and safety advice carefully

CAUTION. Risk of minor or moderate injury through tripping

During assembly and operation, poorly routed Cables may become a trip hazard. Tripping over

Cables may lead to minor or moderate injury.

• Ensure that Cables are routed properly to avoid trip hazards

• Be careful not to trip over Cables when installing the Handset

NOTICE

• Ensure proper ESD handling during assembly. Damage that can be attributed to

electrostatic discharge will void warranty claims.

• To avoid damage to the product, measure the dimensions of the Handset before assembly.

• Before assembly, all parts must be acclimatised to the ambient conditions.

• Do not lift the Handset by its cable. This will cause irreparable damage to the product

• Perform a product risk assessment so that you can respond to potential residual hazards.

Assembly instructions must be included in your end user Operating Manual.

MANUAL

Document Version 2.0 / October 2019

TOUCHfamily

Valid for:

• TOUCHfx

• TOUCHdown

• TOUCHinlay

1 Strain Relief

2 Drilling Holes

3 Memory Position Keys

4 Display

5 UP/DOWN keys

6 SAVE key

*Cable not shown

Supply voltage 5 V DC ± 200 mV

Current Consumption (average) 60 mA

Current Consumption (standby) <1.3 mA

Service life 10 000 cycles

Cable length 2 000 mm / 78.740” (± 40 mm / 1.575”)

Dimensions (l x w x h ) 132.5 × 85.9 × 32.8 mm / 5.216“ x 3.380“ x 1.289“

Weight (including cable) 138 g

Ambient conditions during

operation

+5 °C to +40 °C at max. 68% relative air humidity (non-condensing),

up to an altitude of 2,000 m.

Ambient conditions during

transport and storage

-25 °C to +40 °C at max. 68% relative air humidity (non-condensing).

+40 °C to 60 °C at max. 32% relative air humidity (non-condensing).

Temperatures of more than 40 °C for periods not exceeding 10h.

Product must be acclimatised to acceptable operating conditions

Compatibility All LOGICDATA Control Boxes, except integrated Control Units in

the LOGICdrive and DYNAMIC MOTION families.

Degree of protection (IEC 60529) IP 20

Standards and regulations EMC directive 2014/30/EU

RoHS directive 2011/65/EU

Order Code TOUCH-FX-MDF-4M2-LD (4 Memory Positions, no Key Lock)

TOUCH-FX-MDF-4M2-KL (4 Memory Positions, Key Lock)

TOUCH-FX-MDF-6M2-LD (6 Memory Positions, no Key Lock)

TECHNICAL DATA

85,9 mm

132,5 mm

32,8 mm

Supply voltage 5 V DC ± 200 mV

Current Consumption (average) 60 mA

Current Consumption (standby) <1.3 mA

Service life 10 000 cycles

Cable length 2 000 mm / 78.740” (± 40 mm / 1.575”)

Dimensions (l x w x h ) 132.5 × 85.9 × 32.8 mm / 5.216“ x 3.380“ x 1.289“

Weight (including cable) 138 g

Ambient conditions during

operation

+5 °C to +40 °C at max. 68% relative air humidity (non-condensing),

up to an altitude of 2,000 m.

Ambient conditions during

transport and storage

-25 °C to +40 °C at max. 68% relative air humidity (non-condensing).

+40 °C to 60 °C at max. 32% relative air humidity (non-condensing).

Temperatures of more than 40 °C for periods not exceeding 10h.

Product must be acclimatised to acceptable operating conditions

Compatibility All LOGICDATA Control Boxes, except integrated Control Units in

the LOGICdrive and DYNAMIC MOTION families.

Degree of protection (IEC 60529) IP 20

Standards and regulations EMC directive 2014/30/EU

RoHS directive 2011/65/EU

Order Code TOUCH-FX-MDF-4M2-LD (4 Memory Positions, no Key Lock)

TOUCH-FX-MDF-4M2-KL (4 Memory Positions, Key Lock)

TOUCH-FX-MDF-6M2-LD (6 Memory Positions, no Key Lock)

TECHNICAL DATA

85,9 mm

132,5 mm

32,8 mm

8 Swedstyle Memory T Swedstyle Memory T 9

5.3 DRILLING TEMPLATES

5.3.1 TOU CHFX

Fig. 8: Drilling Template, TOUCHfx

38 mm

70 mm

SIDE EDGE

FRONT EDGE

4.1 Required components

Hand controller

Screwdriver

2 Mounting Screws

4.2 Process

1. Position the Handset under the table top and mark the position of the drilling holes.

If necessary, use the Drilling Template to help you.

2. Insert the Strain Relief into the designated slot on the Handset.

NOTICE Inserting the Strain Relief incorrectly may cause damage to the Cable and Handset.

Ensure that the Cable does not protrude over the housing

3. Use the screwdriver and 2 Mounting Screws to attach the Handset to the Table Top at the

marked drilling points.

NOTICE The required tightening torque depends on the material of the Table Top.

Do not exceed 2 Nm.

4.3 COMPLETING ASSEMBLY

After the ”Memory T” is attached to the Table Top, you must connect the Cable to

the Control Box.

DRILLING TEMPLATE

6.2 ASSEMBLY: TOUCH fx

6.2.1 REQUIRED COMPONENTS

1 TOUCHfx

2 2 Mounting Screws (supplied by Reseller)

Tool Screwdriver

INFO Thread diameter: max. 5 mm | Head diameter: 8.5 mm - 10.6 mm

If possible, do not use countersunk-head screws.

6.2.2 PROC ESS

1. Position the Handset under the table top and mark the position of the drilling holes. If necessary,

use the Drilling Template in chapter 5.3.1 to help you.

2. Insert the Stra in Reli ef into the designated slot on the Handset (Fig. 6).

NOTICE Inserting the Strain Relief incorrectly may cause damage to the Cable and Handset.

Ensure that the Cable does not protrude over the housing

Fig. 10: Inserting the TOUCHfx Strain Relief

3. Use the screwdriver and 2 Mounting Screws to attach the Handset to the Table Top at the

marked drilling points.

NOTICE The required tightening torque depends on the material of the Table Top. Do not exceed

2 Nm.

6.2.3 COMPLETING ASSEMBLY

After the TOUCHfx is attached to the Table Top, you must connect the Cable to the Control Box. Refer to the

manual for your chosen Control Box for instructions.

10 Swedstyle Memory T Swedstyle Memory T 11

5 OPERATION

CAUTION. Risk of minor or moderate injury through uncontrolled movement

The table may not always stop exactly at the expected position. Failure to anticipate the table’s

movements may lead to minor or moderate injury through crushing.

• Wait until the system has completely stopped before attempting to use the table

CAUTION. Risk of minor or moderate injury through unsecured objects

While the table moves up and down, unsecured objects may fall off the table and onto body

parts. This may lead to minor or moderate injury through crushing.

• Ensure loose objects are kept away from the edge of the table

• Do not leave unnecessary objects on the table during movement

CAUTION. Risk of minor or moderate injury through crushing

Failure to release Handset Keys correctly may result in the table failing to stop properly.

This may lead to minor or moderate injury through crushing.

• Do not slide your ﬁnger to a different Handset key while another button is pressed

• Disconnect the system immediately if any Handset Key becomes stuck

INFO. The technology within the Handset may be interrupted by external interferences during

operation. This may lead to certain user inputs (i.e. button presses) not being recognized.

This section of the Operating Manual contains a selection of instructions for operating the Table

System to which the Handset is connected. Handset Keys are represented as follows:

UP Key

DOWN Key

SAVE Key

Memory Position Key 1

Memory Position Key 2

Memory Position Key 3

Memory Position Key 4

5.1 Adjusting the table top height

CAUTION. Risk of minor or moderate injury through crushing

Your ﬁngers may be crushed when you attempt to change the height of the table

• Keep ﬁngers away from moving parts

• Ensure that no persons or objects are in the table’s range of motion

INFO The Table Top will move up or down until the UP or DOWN Key is released,

or if a pre-deﬁned stopping point has been reached.

To move the Table Top UP:

Press and hold until the desired height has been reached

To move the Table Top DOWN:

Press and hold until the desired height has been reached

5.2 Saving a memory position

This function saves a set Table Top position. One Memory Position can be saved

per Memory Position Key.

1. Move the table to the desired height.

The display shows the Table Top height (e.g. 73 cm)

2. Press

3. Press the Memory Position Key (e.g. 2)

4. The display shows

5. After about two seconds, the Table Top height is displayed again

5.3 Adjusting the table to a memory position

Version A (without double-click function):

1. Press and hold the required Memory Position Key (e.g. 2).

The Table Top will move until the saved Table Top height has been reached.

If you release the Key before the Memory Position is reached, the table will stop.

2. Release the Memory Position Key

3. The display shows the Table Top height (e.g. 73 cm)

7 OPERATION

CAUTION Risk of minor or moderate injury through uncontrolled movement

The table may not always stop exactly at the expected position. Failure to anticipate the

table's movements may lead to minor or moderate injury through crushing.

• Wait until the system has completely stopped before attempting to use the table

CAUTION Risk of minor or moderate injury through unsecured objects

body parts. This may lead to minor or moderate injury through crushing.

• Ensure loose objects are kept away from the edge of the table

• Do not leave unnecessary objects on the table during movement

CAUTION Risk of minor or moderate injury through crushing

Failure to release Handset Keys correctly may result in the table failing to stop properly.

This may lead to minor or moderate injury through crushing.

•

• Disconnect the system immediately if any Handset Key becomes stuck

INFO The technology within the Handset may be interrupted by external interferences

during operation. This may lead to certain user inputs (i.e. button presses) not being

recognized.

This section of the Operating Manual contains a selection of instructions for operating the Table System

to which the TOUCH Handset is connected. TOUCH Handsets are compatible with a large number of

LOGICDATA Control Boxes. Before using the Table System, you must also read the Operating Manual for

the installed Control Box, including all relevant safety information, in full.

Handset Keys are represented as follows for further description:

UP Key

DOWN Key

SAVE Key

Memor y Position Key 1

Memory Position Key 2

Memory Position Key 3

Mem ory Position Key 4

SAVE