Swann Smith's Space Saver SS2E Mode d’emploi

Issue 07 - March 2021 | SmithsEP.co.uk | 1

Installation, commissioning

and user manual

SS2E | SS3E | SS80E | SS5 DUAL

Space Saver

Issue 007 | March 2021

ENGLISH | UK | IRL | SmithsEP.co.uk

2 | SmithsEP.co.uk | Issue 07 - March 2021

Introduction

The following items are included in the carton:

• Product complete with grille and pre-wired

mains cable

• Fixing screws (2)

• Wireless controller

• One pair of exible hoses (SS5 Dual only)

Accessory grilles are available in different colours

and nishes. Please consult the price list for

details. In the event of any items missing or visible

damage, please contact us on +44 (0) 1245

324560.

Please leave this Installation and User Manual with

the owner of the property.

Contents

Introduction 2

Declaration of conformity 2

Symbols used in this guide 3

Important safety and installation instructions 3/4

Application 4

Product Information 5

Installation - Heater 7

Installation - Controller 8

Pairing - Controller with Heaters 10

Commissioning 12

Installation - with advanced features 14

Commissioning 12

Fault nding 16

User Manual

Important safety guidance 18

Introduction 19

Operation 20

Fault nding 28

Registering your product 29

Disposal 29

After sales and spares 29

Declaration of conformity

EC Declaration of conformity

We, Smith’s Environmental Products Limited

1-2 Blackall Industrial Estate

South Woodham Ferrers

Chelmsford

Essex CM3 5UW

Tel: 01245 324900 Fax: 01245 324422

Declare under sole responsibility that the products:

Product name:

Space Saver

Product range:

SS2E, SS3E, SS80E, SS5 DUAL

Listed above conrms with the following European

Union directives:

Low Voltage Directive (73/23/EEC)

EMC Directive (89/336/EEC)

Pressure Equipment Directive (97/23/EC)

Machinery (98/37/EC)

Standards comply with the above directives.

Safety Directive Standards:

EN 60335-2-80:2003 + A1:04 in conjunction

with EN 60335-1:2002 + A11:04 + A1:04 +

A12:06 + A2:06

With UK deviations

This Declaration is made on behalf of Smith’s

Environmental Products Limited.

Issue 07 - March 2021 | SmithsEP.co.uk | 3

Ignoring these safety

provisions marked by

the symbol “caution:

electricity” may

endanger the safety

of people, as well

as the integrity

of the equipment.

Symbols

This manual contains information and prescriptions marked by the following symbols:

Ignoring these safety

provisions marked by

the symbol “caution:

hazard” may

endanger the safety

of people.

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety. Children should be supervised to ensure that they do not play

with the appliance.

To guard against injury, basic safety precautions should be observed, including the

following:

1. Read and follow all safety instructions and all the important notices on the appliance

before installing, using and maintaining the appliance. Failure to do so may cause

personal injury or damage to the appliance or installation.

2. Always disconnect electrical supply before putting on or taking off parts and whilst the

equipment is being installed, maintained or handled. Never work with bare feet and/or

with wet hands.

3. Carefully examine the appliance before and after installation.

Do not operate the appliance if it has a damaged supply cord or enclosure, or if it

is malfunctioning or it is dropped or damaged in any manner. Inspect the

appliance periodically.

4. Improper use.

Do not use this appliance:

• In locations where special conditions prevail, such as the presence of a corrosive or

explosive atmosphere (dust, vapour or gas) (EN60335-2-51);

• For other than intended use.

5. Installation.

The appliance must be mounted in a stable/xed position in a dry, well ventilated,

frost-free, waterproof and protected place, with sufcient ventilation around it. Make

sure that the appliance is securely and correctly installed before operating it and that

there is enough room around it for maintenance operations, dismantling, checking for

free inspection.

The maximum ambient temperature at which the appliance is to be used is 40°C

(EN60335-2-51).

Important safety and installation instructions

Prior to installation, read these installation and operating instructions. The installation and operation should

also be in accordance with national regulations and accepted codes of good practice.

High temperature

surface.

Take utmost care

to prevent people

from getting in

contact with the

hot surfaces of the

appliance.

4 | SmithsEP.co.uk | Issue 07 - March 2021

6. Electrical connection

IMPORTANT: Connection to the power supply must be effected by means of a xed

power cable which is tted with a plug-type connection or a two pole isolating switch

with a minimum contact opening of 3 mm.

Electrical connection must be carried out by a qualied electrician and in

accordance with local regulations and both data on the name-plate and the

appropriate diagram inside the terminal box cover.

Follow all safety standards.

7. Connect the appliance only to a mains supply protected by a Residual Current Device

(RCD or Ground-Fault Circuit-Interrupter) with a rated residual operating current not

exceeding 30mA.

8. Prior to any modication being made to the equipment, it must be agreed with and

authorised by the manufacturer. Original spare parts and accessories authorised by the

manufacturer are integral part contributing to the safety of the equipment and of the

machines. The use of non original components or accessories may endanger the safety

and causes the termination of the warranty. Safe operation is only assured for the

applications and conditions described in Application of this manual.

Non-observance of the safety instructions results in the loss of any claims to damages.

The indicated limit values are binding and cannot be exceeded for any reason whatsoever.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Important safety and installation instructions

Prior to installation, read these installation and operating instructions. The installation and operation should

also be in accordance with national regulations and accepted codes of good practice.

Application

Space Saver is primarily intended for installation in the space beneath kitchen cupboards behind the plinth.

However, it can be also installed in similar applications such as stair cases and other built-in furniture.

This Space Saver model must NOT be installed in a bathroom or other areas of high humidity. Please contact

us on +44 (0) 1245 324560 for details of products suitable for these applications.

In compliance with LOT20 European legislation, this product is supplied with a wireless battery powered

wall-mounted time and temperature controller. This heater will NOT function without the wall-mounted

controller. The controller can control an unlimited number of heaters.

Space Saver is tted with an overheat protection. The heater will automatically stop in the event of the

heating elements reaching the cut-out temperature.

SS5D dual models are designed for use on standard two -pipe pumped central heating systems. Pipes are

15mm and either may be used as ow or return. The product is not suitable for one-pipe systems.

Please note the guarantee may be invalidated if this product is not installed and used in accordance with

this guide.

Issue 07 - March 2021 | SmithsEP.co.uk | 5

SS3E

Product dimensions

and performance

SS2E

Heat output

240

100

105

290 91

500

485

Heat Output

(kW)

Power

Consumption

(kW)

Fused

spur

Mains Cable

(m)

1kW/2kW 1kW/2kW 10A 2.0

Voltage: 230V

600

585

380 86

170

110 9110

LED lens

100*

*Overall height

inc. rubber feet

Heat output

Heat Output

(kW)

Power

Consumption

(kW)

Fused

spur

Mains Cable

(m)

1kW/2kW/3kW 1kW/2kW/3kW 13A 2.0

304

460

78 78 77

212

203

Heat output

Heat Output

(kW)

Power

Consumption

(kW)

Fused

spur

Mains Cable

(m)

0.6kW/1.2kW 0.6kW/1.2kW 10A 2.0

SS80E

6 | SmithsEP.co.uk | Issue 07 - March 2021

Product dimensions and

performance

12 20

Pattress

500

475

322 20 91

Pipe centres

100

288

100

135

Heat output - electric mode

Heat Output

(kW)

Power

Consumption

(kW)

Fused

spur

Mains Cable

(m)

1kW 1kW 5A 2.0

SS5 DUAL WALL CONTROLLER

Heat output - hydronic mode

It is recommended that the Space Saver model chosen is capable of maintaining the calculated heat loss at

normal heat output (l) enabling the boost setting (ll) to be used for faster heat up.

*Room sizes given in cubic metres for general guidance only based on normal heat output (80ºC) for domestic applications - always calculate

heat losses. Heat outputs tested in accordance with BS4856 using entering water temperature and 340 l/h (75gph) ow rate. Fan-only option

operational only when central heating system is switched off. Dual models include an electric element which in electric heating mode will emit

1kW of heat. If the heating system comes on whilst the Space Saver is switched to electric heating mode, the element will automatically switch

off. Using Hydronic heating mode where possible will considerably reduce running costs.

Model

Room size

guide* (m3)

Heat Output at 80° Heat Output at 75° Heat Output at 70° Heat Output at 65°

Normal

(kW)

Boost

(kW)

Normal

(kW)

Boost

(kW)

Normal

(kW)

Boost

(kW)

Normal

(kW)

Boost

(kW)

Hydronic/Electric (Dual)

SS5 Dual (hydronic mode) 37 1.3 1.7 1.2 1.6 1.1 1.4 1.0 1.3

SS5 Dual (electric mode) 29 1.0 - 1.0 - 1.0 - 1.0 -

Model

Room size

guide* (m3)

Heat Output at 60° Heat Output at 55° Heat Output at 50° Heat Output at 45°

Normal

(kW)

Boost

(kW)

Normal

(kW)

Boost

(kW)

Normal

(kW)

Boost

(kW)

Normal

(kW)

Boost

(kW)

Hydronic/Electric (Dual)

SS5 Dual (hydronic mode) 37 0.9 1.1 0.8 1.0 0.7 0.9 0.6 0.8

SS5 Dual (electric mode) 29 1.0 - 1.0 - 1.0 - 1.0 -

Issue 07 - March 2021 | SmithsEP.co.uk | 7

1. Cut the opening in the plinth

• To ensure adequate airow, a minimum

clearance of 20mm (10mm for SS80E product)

between the top of the product and any

shelving is essential

• To avoid the possibility of vibration, this product

must be installed on a at, even surface

• There must be no rear access to the product

after completion of the installation

• We recommend the use of a knee pad when

installing this product

• Cut the opening in the plinth to the size shown

in the table. Use method 1 or 2.

3 represents installation into a 80mm plinth

(SS80E only)

* The overall height of the grille is 100mm.

Use care when cutting the opening.

Installation - Heater

Model Width A

(mm)

Height B*

(mm)

SS2E 465 96

SS3E 570 95

SS80E 400 74

SS5 DUAL 465 96

2a. Connection for SS5 Dual

Heater - Fit isolating valves

(not supplied)

• Fit isolating valves (not supplied) to the system

ow and return pipes. In order to achieve the

highest level of performance we recommend

full bore valves

• Failure to t isolating valves may mean that the

product is not serviceable in the event of failure

• Connect the exible hoses between system

pipework and heater. Please ensure the exible

hoses are not kinked

• Open the isolating valves and check for leaks

N.B. either pipe may be used on ow or return.

The Flexible installation hoses supplied are suitable

for use with either 15mm diameter copper pipe or

15mm cross-linked polythene barrier pipe to

BS 7291. The only type of tting approved to

connect onto the heater are compression ttings.

2b. Vent air through bleed

Open Closed

8 | SmithsEP.co.uk | Issue 07 - March 2021

5. Overlay grille (optional)

• If required t the overlay grille

• Remove the screws holding the xed grille

to the plinth

• Place the overlay grille over the xed grille

and ret the screws

Installation - Controller

Introduction

In compliance with LOT20 European legislation, this

product is supplied with a wireless battery powered

wall-mounted time and temperature controller.

The product will NOT function without the wall-

mounted controller. The controller can control an

unlimited number of heaters.

The controller is primarily designed to minimise

energy wastage and ensure the room is maintained

at the comfort level set by the user. In the basic

setting, the controller is a simple room thermostat

in which the heater will run until the set

temperature is reached. If the room temperatures

falls the heater will switch on again until the set

temperature is reached. The operating range is

between 15°C and 35°C.

The controller also has a number of advanced

features that, if required MUST be set during

the installation process. Please discuss with your

customer which features they require.

• Temperature control for Comfort (COMF)

This can be set to limit the maximum

temperature set by the user

• Temperature control for Setback (SETB)

This can be used for frost protection or situations

where a minimum room temperature must be

maintained. The setback temperature can be set

between 0°C and 15°C

2c. Electrical connection - Heater

• Isolate the electrical supply and connect the

heater electric cable to the fused spur

• The fused spur must not be directly above the

heater, but should be accessible after

completion of the installation

Electrical installation should be carried out by a

competent installer, preferably registered with

NICEIC (National Inspection Council for Electrical

Installation Contracting) in accordance with the 17

edition of the IEE Wiring Regulations, (BS.7671),

and any relevant Local Authority Bye-Laws.

This heater is tted with a 3-core mains supply

cable and should be permanently connected to

the electricity supply via a double pole switch

having 3mm gap on each pole. A switched

Fused Connection unit to BS.1363. Part 4 is a

recommended mains supply connection accessory

to ensure compliance with safety requirements

applicable to xed-wiring installation.

3. Position heater

• Position the heater, making sure the electrical

cable is not snagged

4. Fix to plinth

• Fix heater to plinth

Grille to plinth securing screws

Issue 07 - March 2021 | SmithsEP.co.uk | 9

1. Choosing a position in a room

for the wall controller

The Controller should be positioned 1.5m above

the oor and in the same room/space as the heater.

The controller should be xed to the wall. Avoid

areas with draft or direct sun. Do not position the

controller above or close to the heaters or other

heat sources. Damp areas or areas where the

controller can be mechanically damaged should

also be avoided. Avoid installing the controller

in areas where there are metal objects between

the heater and the controller. This will reduce

the RF range. The RF range in ideal conditions

can be up to 20m however this can be reduced

when the signal is passing through the walls or

other objects. The range can be also affected

where the controller is mounted close to power

cables, motors or equipment producing strong

electromagnetic eld. If the temperature control

feature is used it is necessary to use one controller

for each room or zone.

2. Installation - Basic Setting

The controller is supplied with a white plastic

mounting box that needs to be xed to a wall at

1.5m above oor level. The controller is powered

by two AAA batteries, supplied. To activate the

controller pull the plastic tab located at the +

battery terminal. The batteries should be replaced

every 12 months.

✘

1.5m

✔

• Run-back Timer

This can be used to limit the run time of the

heater from between 5 minutes and 2 hours

The Run-back Timer cannot used be used in

conjunction with Temperature control for

Setback (SETB).

10 | SmithsEP.co.uk | Issue 07 - March 2021

Thermostat Controller -

Quick Set up

IMPORTANT – THIS HEATER WILL NOT WORK

UNLESS USED AND PAIRED WITH THE SLVTB

THERMOSTAT CONTROLLER

1. Ensure the heater is correctly

installed and connected to the

mains power supply.

DO NOT TURN THE MAINS

POWER ON AT THE WALL

UNTIL INDICATED IN THE

INSTRUCTIONS BELOW.

2. Remove the thermostat from the box and

packaging. Remove the two screws to access

the back of the SLVTB thermostat Controller.

The clear plastic tag should be pulled out from

the end of the battery holder. The screen should

now show the current room temperature.

Note: If you are using any of the advanced

features, these should be set now (see full

instruction detail within Installation and User

Guide)

3. Set the heater fan switch to ON (leave the

mains power OFF at the wall)

4. Turn ON the mains power at the wall and

within 20 seconds press and hold the large

ON/OFF button on the SLVTB thermostat

controller, keep pressing button, PAIR and

then TEST will appear on the screen.

Once TEST appears on the screen release the

button and the fan in the heater should run.

Note: Failure to switch on the mains power

and press the controller ON/OFF button within

20 seconds will result in the heater and

controller not pairing and pairing process

should be restarted from step 3

5. To exit the pairing mode, press

the ON/OFF button on the

SLVTB thermostat controller

ONCE (DO NOT HOLD THE

BUTTON IN).

The room temperature will

now be shown.

6. Set the heat output switches on the front of the

heater to the desired position.

7. Press the large ON/OFF button on the SLVTB

thermostat controller ONCE (DO NOT HOLD

THE BUTTON IN). You will see a heating

symbol appear in the bottom left hand corner

of the screen; this indicates the thermostat is

turned on.

8. Using the UP and DOWN

symbols buttons on the SLVTB

controller set the temperature

to the desired setting. Press

the up arrow to increase the

target temperature or the

down arrow to decrease the

target temperature.

Providing the target temperature is higher than

the room temperature the heater will operate.

Note: If the heat symbol ashes the target

temperature of the SLVTB thermostat controller is

lower than the current room temperature – if the

heat symbol is solid the SLVTB thermostat

controller target temperature is higher than the

current room temperature.

Fan Switch to ON

Heating

symbol

OFF

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Swann Chauffage

Swann

Swann Smith's Caspian LST EC Series Mode d’emploi

Swann

Swann Retro SH60010 Manuel utilisateur

Swann

Swann Smith's Ecovector II Low Level Mode d’emploi

Swann

Swann Smith's Multivector-EC Series Mode d’emploi

Swann

Swann Smith's Caspian EC Series Mode d’emploi

Swann

Swann Smith's Caspian EC Series Manuel utilisateur

Swann

Swann Smith's Ecovector II Smart LL Mode d’emploi

Swann

Swann Smith's Solano Eco Mode d’emploi

Swann

Swann Smith's Solano Eco 1 Mode d’emploi

Swann

Swann Smith's Caspian CTFF Series Mode d’emploi

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur