Sutron TPE057ATQ Manuel utilisateur
User Manual
Slim Line Outdoor Touch Panel
Part Number: 80860.768
Version: 1
Date: 2010-08-06
Valid for: TPE057ATQ
Slim Line Touch Panel
Version Date Modifications
1 06.08.2010 First Edition
This manual, including all illustrations contained herein, is copyright protected. Use of this manual by any third
party in departure from the copyright provision is forbidden. No part of this manual may be reproduced, trans-
lated or electronically or photographically archived or altered without the express written consent from Sütron
electronic GmbH. Violations shall be cause for damage liability.
Sütron electronic reserves the right to make any changes that contribute to technical improvement.
Slim Line Touch Panel Overall Table of Contents
i
Overall Table of Contents
1 Important Notes ....................................................................................................... 1-1
1.1 Symbols .................................................................................................... 1-1
1.2 Safety Notes ............................................................................................. 1-1
1.3 Intended Use............................................................................................. 1-2
1.4 Target Group............................................................................................. 1-2
2 Installation and Commissioning ............................................................................... 2-1
2.1 Unpacking the Device ............................................................................... 2-1
2.2 Mounting the Device ................................................................................. 2-1
2.2.1 Front Panel Dimensions ...................................................................... 2-2
2.2.2 Mounting Cutout .................................................................................. 2-3
2.2.3 Side View, Mounting Depth ................................................................. 2-4
2.3 Connecting the Device.............................................................................. 2-5
2.3.1 Supply Voltage 24 V ............................................................................ 2-5
2.4 Switching On............................................................................................. 2-7
2.4.1 Loading Procedure on Windows CE Operating Procedure ................. 2-7
2.4.1.1 Launch Overview ........................................................................................................2-8
2.4.1.2 Normal Mode ..............................................................................................................2-9
2.4.1.3 Setup Main Mode........................................................................................................2-9
2.4.1.4 Administration Operating Mode ................................................................................2-19
2.4.2 Important Files and Update ............................................................... 2-20
2.5 Identification............................................................................................ 2-21
2.5.1 Version Key ....................................................................................... 2-21
3 Control and Display Elements ................................................................................. 3-1
3.1 Display ...................................................................................................... 3-1
3.1.1 Touch Screen ...................................................................................... 3-1
4 Interfaces of the Device ........................................................................................... 4-1
4.1 Ethernet (X5)............................................................................................. 4-2
4.1.1 Pin Assignment .................................................................................... 4-2
4.1.2 Cable ................................................................................................... 4-2
4.1.3 Diagnostics .......................................................................................... 4-3
4.2 USB (X9, X10) .......................................................................................... 4-3
4.2.1 Cable ................................................................................................... 4-3
5 Maintenance and Servicing ..................................................................................... 5-1
5.1 Front Panel ............................................................................................... 5-1
5.2 Fuse .......................................................................................................... 5-1
6 Technical Data......................................................................................................... 6-1
Overall Table of Contents Slim Line Touch Panel
ii
6.1 Generally................................................................................................... 6-1
6.2 TPE057ATQ.............................................................................................. 6-3
7 Ordering Data...........................................................................................................7-1
A Index ....................................................................................................................... A-1
Slim Line Touch Panel Important Notes
1-1
1 Important Notes
1.1 Symbols
The symbols in this manual are used to draw your attention on notes and dangers.
1.2 Safety Notes
– Read this manual carefully before using the operating device. Keep this manual
in a place where it is always accessible to all users.
– Proper transportation, handling and storage, placement and installation of this
product are prerequisites for its subsequent flawless and safe operation.
– This user manual contains the most important information for the safe operation
of the device.
– The user manual, in particular the safety notes, must be observed by all person-
nel working with the device.
– Observe the accident prevention rules and regulations that apply to the operating
site.
– Installation and operation must only be carried out by qualified and trained per-
sonnel.
This is the safety alert symbol. It is used to alert you to potential personal injury haz-
ards. Obey all safety messages that follow this symbol to avoid possible injury or
death.
DANGER
This symbol is used to refer to instructions which, if ignored or not carefully followed,
will result in death or serious injury.
WARNING
This symbol is used to refer to instructions which, if ignored or not carefully followed,
could result in death or serious injury.
CAUTION
This symbol is used to refer to instructions which, if ignored or not carefully followed,
could result in minor or moderate injury.
NOTICE
This symbol and the accompanying text alerts the reader to a situation which may
cause damage or malfunction to the device, either hardware or software, or sur-
rounding property.
Reference to source of information
This symbol refers to detailed sources of information on the current topic.
Important Notes Slim Line Touch Panel
1-2
1.3 Intended Use
– The device is designed for use in the industry.
– The device is state-of-the art and has been built to the latest standard safety re-
quirements. However, dangerous situations or damage to the machine itself or
other property can arise from the use of this device.
– The device fulfills the requirements of the EMC directives and harmonized Euro-
pean standards. Any modifications to the system can influence the EMC behav-
ior.
1.4 Target Group
All configuration, programming, installation, commissioning, operating and mainte-
nance work in connection with the automation system must be performed by trained
personnel only (e.g. qualified electricians, electrical engineers, etc.).
The configuration and programming personnel must be familiar with the safety con-
cepts of automation technology.
The operating personnel must have been trained in handling the controller and be
familiar with the operating instructions.
The installation, commissioning and maintenance personnel must have an education
which entitles them to work on automation systems.
Slim Line Touch Panel TPE057ATQ Installation and Commissioning
2-1
2 Installation and Commissioning
2.1 Unpacking the Device
Unpack all parts carefully and check the contents for any visible damage in transit.
Also check whether the shipment matches the specifications on your delivery note.
If you notice damages in transit or discrepancies, please contact our sales depart-
ment immediately.
2.2 Mounting the Device
The operating device can be easily and quickly mounted from the rear of the operat-
ing device. This is particularly recommended for mounting in switchboards with a
plate thickness of approx. 1 mm to 6 mm (0.039" to 0.236").
1. Insert the operating device from the front through the mounting cutout.
2. Fasten the operating device using hexagon nuts.
NOTICE: Damage
When installing the device, leave a gap of at least 30 mm (1.181") around the device
to ensure sufficient air circulation.
NOTICE: Damage
When the operating device is installed horizontally, please note that additional
sources of heat beneath the operating device may result in heat accumulation.
Make sure to allow sufficient heat dissipation!
Comply with the allowable temperature range listed in the technical data for the use
of the operating device!
NOTICE: Damage
To maintain the specified degree of protection, make sure the seal is evenly seated
on the installation surface and the hexagon nuts are tightened uniformly.
Ensure that the maximum torque of 1 Nm is not exceeded.
Installation and Commissioning Slim Line Touch Panel TPE057ATQ
2-2
2.2.1 Front Panel Dimensions
Figure 2-1 TPE057ATQ
Slim Line Touch Panel TPE057ATQ Installation and Commissioning
2-3
2.2.2 Mounting Cutout
Figure 2-2 TPE057ATQ
AMounting Cutout
BFront Panel
Installation and Commissioning Slim Line Touch Panel TPE057ATQ
2-4
2.2.3 Side View, Mounting Depth
Figure 2-3 TPE057ATQ
1Front Panel
2Circumferential Seal
3Press-in Threaded Bolt M4 x 16 mm (0.629")
4Mounting Surface Thickness 1 mm to 6 mm (0.039" to 0.236")
5Spring Lock Washer B4 DIN 127 Form B (not supplied)
6Nut M4 DIN 934 (not supplied)
Table des matières
Autres manuels Sutron Écran tactile
Manuels Écran tactile populaires d'autres marques
IBASE Technology
IBASE Technology ASTUT-152-RE1S Manuel utilisateur
YASKAWA
YASKAWA TP 610C Manuel utilisateur
B&R
B&R Power Panel C Series Manuel utilisateur
Beijer Electronics
Beijer Electronics X2 control Manuel utilisateur
AXIOMTEK
AXIOMTEK GOT321W-521 Manuel utilisateur
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Manuel utilisateur
