Suspa MOVOTEC Manuel utilisateur
P/N: 670-00020
8/25/08
Movotec®ATU Workstation
Kit Assembly Instructions
by
Copyright © 2008 by
Suspa® Incorporated
All rights reserved. No part of this manual may be reproduced or transmitted
in any form or by any means, electronic or mechanical, including photocopying,
recording, or by any information storage and retrieval system
without permission in writing from Suspa® Incorporated.
P/N: 670-00020
8/25/08
1
1.0 Safety Instructions
READ ALL INSTRUCTIONS BEFORE ATTEMPTING TO INSTALL,
OPERATE, OR SERVICE A MOVOTEC®ATU WORKSTATION.
This document contains basic safety and installation instructions for assembling a Movotec®ATU
Workstation Kit when used in conjunction with a Movotec® ATU and lift system.Please refer to
Movotec® Crank Driven and E-Drive ATU Lift System Manuals for detailed lift system safety, installation,
operation, troubleshooting, and maintenance instructions. Suspa®Incorporated is not responsible for any
alteration, misuse, misapplication, or abuse of this product resulting in property damage, personal injury or
death.
FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS
DOCUMENT COULD RESULT IN FIRE, PROPERTY DAMAGE,
ELECTRIC SHOCK, PERSONAL INJURY OR DEATH.
______________________________________________________________________________________
2.0 Component Callout
P/N: 670-00020
8/25/08
2
3.0 Component List
The Movotec®ATU Workstation Kit includes:
•(2) - Foot brackets
•(2) - Top brackets
•(2) - Cross beam brackets
•(1) - Cross beam
•(8) - 5/16”-18 forming screws
•(4) - Glides
•(4) - M10 hex nuts
•(8) - M10 washers
•(4) - End plugs
•(2) - Hole plugs
•(4) - 1/4”-20 flat head screws
•(4) - 1/4”-20 hex nuts
•(4) - #14 tapping screws
•(3) - 13mm retaining rings
4.0 Recommended Tools
The following tools will be required to assemble the Movotec®ATU Workstation Kit. Please note that
tools are not included with kit.
•Soft Face Hammer
•1/2” Drive Ratchet
•1/2” Drive Extension
•13mm Hex Socket
•17mm Wrench
•Power Drill
•#3 Phillips Head Drive Bit
•Retaining Ring Pliers
•5/32” Allen Wrench
P/N: 670-00020
8/25/08
3
5.0 Foot Bracket Installation
Install M10 washer onto glide thread.
Insert glide thread into hole at end of foot bracket.
Fasten glide to foot bracket using M10 washer and M10 hex nut.Repeat for each glide and foot bracket.
P/N: 670-00020
8/25/08
4
Insert end plugs into open ends of both foot brackets using soft-face hammer, if necessary.
Align foot bracket with bottom ATU in the desired mounting configuration (cantilever or centered).
Cantilever Configuration Centered Configuration
Fasten foot bracket to bottom of ATU using (2) 5/16”-18 thread forming screws. Please note that the
function of the thread forming screw is to cut threads into the ATU as the screw is driven into the material.
Cantilever Configuration Shown
P/N: 670-00020
8/25/08
5
Insert hole plug into unused mounting hole.
Repeat foot bracket assembly procedure for second ATU.When fastening second foot bracket to the ATU,
make sure that the tubing cutout is facing inwards in relation to the other ATU.
Cantilever Configuration Shown
6.0 Cross Beam Installation
Fasten cross beam bracket to cross beam using (2) #14-3/4 tapping screws.The tapping screws require a
#3 Phillips driver for installation.Please note that the function of the tapping screw is to cut threads into
the cross beam as the screw is driven into the material.
P/N: 670-00020
8/25/08
6
Repeat second cross beam bracket installation on opposite end of cross beam.
Insert 1/4”-20 flat head cap screw into outer cross beam bracket holes. The flat head cap screws require a
5/32” hex socket driver for installation.
Thread 1/4"-20 hex nut onto each flat head screw, leaving approximately 4mm of the screw thread exposed.
Repeat screw and hex nut installation on opposite end of cross beam.
To prepare for cross beam mounting, position ATU legs as shown below.
P/N: 670-00020
8/25/08
7
Align and insert the cross beam bracket hex nuts into ATU T-slot.Repeat cross beam installation on
second ATU.
Position cross beam assembly at desired mounting height. The recommended position is 400mm
(15.75 in.) from the top of the ATU to the centerline of the cross beam.
Fasten cross beam assembly to ATU legs by tightening the (4) flat head screws of the cross beam brackets.
P/N: 670-00020
8/25/08
8
7.0 Cylinder & Top Bracket Installation
Before installing the top brackets, the pump should be placed in between the ATU legs in a secured
position. This will allow each cylinder to be inserted into the ATU legs without damaging the hydraulic
tubing.
Insert cylinder into ATU as shown. The plastic cylinder block will rest on structural tabs inside the ATU
leg.
Orient cylinder head so that tubing exits the ATU tubing cutout as shown.
Align top bracket with top of the ATU in the desired mounting configuration, cantilever or centered. Insert
cylinder head into top bracket mounting hole as shown.
Cantilever Configuration Centered Configuration
P/N: 670-00020
8/25/08
9
Install 13mm retaining ring into cylinder head retaining ring groove using retaining ring pliers.
Fasten top bracket to ATU using (2) 5/16”-18 thread forming screws. Please note that the function of the
thread forming screw is to cut threads into the ATU as the screw is driven into the material.
Cantilever Configuration Shown
Repeat top bracket installation procedure on second ATU leg.
Autres manuels pour MOVOTEC
3
Table des matières
