SUNRICH TECHNOLOGY N-460 Manuel utilisateur
PCIe 4-Port 10G SFP+
Network Controller Card
User Manual
Ver. 1.00
All brand names and trademarks are properties of their
respective owners.
Contents:
Chapter 1: Introduction ......................................................3
1.1 Product Introduction ....................................................3
1.2 Features........................................................................3
1.3 Requirements ...............................................................4
1.4 Package Contents.........................................................5
Chapter 2: Getting Started .................................................5
2.1 Hardware Installation ..................................................5
2.2 Driver Installation........................................................5
2.2.1 Installation for Windows.......................................6
Page 2
Chapter 1: Introduction
1.1 Product Introduction
This PCIe 10G SPF+ Network Card is a cost-effective solution that
delivers fast and reliable 10 Gbps network access at longer distances
than copper-based networks. Using the SPP+ transceiver of your
choice, you can connect your PCI Express-based server or workstation
directly to your 10G fiber optic network.
1.2 Features
Quad port full height 10GbE adapter
Supports common 10GbE SFP+ optical and Direct Attached
Copper modules
EEE (Energy Efficient Ethernet)
Up to 9K Jumbo Frames
IP, TCP and UPD checksum offloading (IPv4, IPv6) capabilities
Designed to meet PCI Express Specification Revision 3.0
Eight lane (x8) PCI Express compatible with x8 and x16 PCI
Express slots
Page 3
IEEE 802.1Q Tagged VLAN
Intel PROSet Utility for Microsoft Device Manager
1.3 Requirements
Hardware
The following system specs are recommended minimum
PCIe slot: Available 8-Lanes PCI-Express slot gen 2.0 or later
Processor: Quad Core 3.0GHz or higher
RAM: 4GB memory or higher
Software
Operating systems supported (64 bits only)
Windows 7
Windows Server 2008 R2
Windows Server 2012
Windows 8.1
Windows Server 2012 R2
Windows 10
Linux 3.16 or later
Page 4
1.4 Package Contents
1 x PCIe 10G SFP+ Network Card
1 x Driver CD
1 x User Manual
Chapter 2: Getting Started
2.1 Hardware Installation
1. Turn off the power to your computer.
2. Unplug the power cord and remove your computer’s cover.
3. Remove the slot bracket from an available PCIe slot.
4. To install the card, carefully align the card’s bus connector with
the selected PCIe slot on the motherboard. Push the board down
firmly.
5. Replace the slot bracket’s holding screw to secure the card.
6. Secure the computer cover and reconnect the power cord.
2.2 Driver Installation
The following section shows you how to install PCIe 10G SFP+
Network Card driver on different operating systems.
Page 5
2.2.1 Installation for Windows
Insert the provided CD into your disk drive. The CD-ROM
will start automatically. The following screen will show up and
please click “Install Driver”.
*Note: Actual image may vary
Note: If the install program doesn’t run automatically, please
locate and double-click on the Autorun.exe file in the CD to
launch the install program.
Please click “PCIe 10G” to start the installation.
Page 6
*Note: Actual image may vary
Follow the instructions on screen to install the driver.
Page 7
Table des matières
Autres manuels SUNRICH TECHNOLOGY Carte réseau
Manuels Carte réseau populaires d'autres marques
3Com
3Com EtherLink 3C509B Manuel utilisateur
TRENDnet
TRENDnet TEG-PCITX Manuel utilisateur
Cisco
Cisco MC16E Manuel utilisateur
Delta Electronics
Delta Electronics Braking Modules VFDB Series Manuel utilisateur
TwinMOS
TwinMOS Booming Manuel utilisateur
Dialogic
Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur
Buffalo
Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur
National Instruments
National Instruments NI 9234 Manuel utilisateur
Hama
Hama 49276 Manuel utilisateur
Linksys
Linksys WCF54G - Wireless-G Compact Flash Card Manuel d'utilisation
Compaq
Compaq Wireless LAN 100 Manuel utilisateur
Bose
Bose PowerMatch Dante Manuel utilisateur