Sunna Design Sol EVERGEN M Series Manuel utilisateur
SINGLE PANEL SIDE MOUNT USER MANUAL
EVERGEN M SERIES
1
Sol by Sunna Design | 990 Biscayne Boulevard, Office 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighting.com
87604_Single_Panel_Side_Mount_Manual_RevA
2
SINGLE PANEL SIDE MOUNT USER MANUAL
COMPONENTS
Sol by Sunna Design | 990 Biscayne Boulevard, Office 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighting.com
Item Description Quantity
1Large Bucket 2
2Clips 4
3PV Rails 2
4Support Rails (combine to create 2 rails) 4
5Banding (for up to 4.5” OD) 4
6
Hardware:
•Buck and Clip Hardware
•5/16-18 ¾” Bolts, Washers, Lock Washers, Nuts
•Support Rail Hardware
•5/16-18 ¾” Bolts, Washers, Lock Washers, Nuts
•Panel Hardware
•1/4-20 ¾” Bolts, Washers, Lock Washers, Nuts
•Spare Hardware
•5/16-18 ¾” Bolts, Washers, Lock Washers, Nuts
16 Sets
6 Sets
4 sets
2 set
Tools:
•5/16 and 1/2 inch socket and wrench
•Torque Wrench
•Banding Tools
•Tape Measure
•Compass
Notes:
•This mount is designed to be installed on a variety of pole sizes achieving 30 or 45 degree
panel tilt.
•The provided banding will work on 2” to 4.5” poles. For Poles with diameter greater then
4.5” you will need to source your own 1/2” banding materials.
SINGLE PANEL SIDE MOUNT USER MANUAL
INSTALLATION
3
Sol by Sunna Design | 990 Biscayne Boulevard, Office 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighting.com
Step 1
A. Using banding, install top support bucket at the desired height on the pole facing it directly
south towards the equator. Use a compass to verify.
B. From the center of the top bucket, install the center of the bottom bucket 32.75 inches below,
facing the same direction.
C. Install all clips in the proper orientation; all clips face in, top clips have the arc facing down,
bottom clips have the arc facing up. Using 5/16-18 hardware, hand tighten all nuts and bolts
for adjustment later.
32.75in
SINGLE PANEL SIDE MOUNT USER MANUAL
INSTALLATION
4
Sol by Sunna Design | 990 Biscayne Boulevard, Office 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighting.com
Step 2
A. Install PV support rails, channels facing out, on the outside of the top clips using 5/16
hardware and hand tighten.
B. Adjust top clips evenly so that the center of the PV rail mounting slots are 33.5in apart at
the top of the PV rail.
33.5in
Step 3
A. Combine two smaller support rails to make one large rail. Rails should nest into each
other so the holes line up using 5/16 hardware. Tighten all hardware to 144 in-lbs.
A-30) For 30 degrees tilt, rails should overlap 7 inches in the middle with the total
length being 31 inches.
A-45) For 45 degrees tilt, rails should overlap 13 inches in the middle with the total
length being 25 inches.
31 in
7 in
25 in
13 in
SINGLE PANEL SIDE MOUNT USER MANUAL
INSTALLATION
5
Sol by Sunna Design | 990 Biscayne Boulevard, Office 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighting.com
Step 4
A. Attach support rail on the inside of the PV rail depending on your tilt
A-30) For 30 degrees tilt, use the 4th hole up from the bottom of the PV rail with a
31in support rail, secure with 5/16 hardware and hand tighten.
A-45) For 45 degrees tilt, use the 1st hole up from the bottom of the PV rail with a
25in support rail, secure with 5/16 hardware and hand tighten.
B. Attach support rail to the bottom clips using 5/16 hardware and hand tighten.
C. Adjust bottom clips evenly so that the center of the PV rail mounting slots are 33.5in
apart at the bottom of the PV rail.
33.5in
33.5in
*30 Degree Setup Shown
SINGLE PANEL SIDE MOUNT USER MANUAL
INSTALLATION
6
Sol by Sunna Design | 990 Biscayne Boulevard, Office 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighting.com
Step 5
A. Insert washer and 1/4-20 3/4in bolt into the non rivnut hole in the back of the solar
panel frame.
B. Mount PV panel onto the bottom section of the rail. Secure with remaining
hardware and tighten to 84 in-lbs.
C. Secure loose PV harnessing with ties.
D. Tighten all loose hardware to 144 in-lbs. Double check previously tightened
hardware.
*30 Degree Setup Shown
7
SINGLE PANEL SIDE MOUNT USER MANUAL
WARRANTY
Sol by Sunna Design | 990 Biscayne Boulevard, Office 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighting.com
Warranty
This product is covered by the Sol warranty. Visit
www.solarlighting.com for additional information or
contact the customer service department.
Before contacting Sol’s customer service department,
please have the serial number of your system available, a
brief description of the problem, as well as all details of the
installation.
To contact Sol’s customer service department:
Mail: Sol by Sunna Design
990 Biscayne Boulevard, Office 701,
Miami, FL 33132, USA
Phone: 1.772.286.9461
1.800.959.1329 (Toll Free in U.S. and Canada)
Email: customerservice@solarlighting.com
Website: solarlighting.com
Autres manuels pour Sol EVERGEN M Series
8
Table des matières
Autres manuels Sunna Design Panneau solaire
Sunna Design
Sunna Design Sol EVERGEN M Series Manuel utilisateur
Sunna Design
Sunna Design Sol EVERGEN M Series Manuel utilisateur
Sunna Design
Sunna Design Sol EVERGEN M Series Manuel utilisateur
Sunna Design
Sunna Design Sol EVERGEN M Series Manuel utilisateur
Sunna Design
Sunna Design Sol EVERGEN M Series Manuel utilisateur
Sunna Design
Sunna Design Sol EVERGEN M Series Mode d’emploi
