Sunjoe SJPPH48 Manuel utilisateur

A Division of Snow Joe®, LLC Model SJPPH48 Form No. SJ-SJPPH48-880E-M

OPERATOR’S MANUAL

OUTDOOR PROPANE HEATER

48000 BTU MAX | QUICK-START IGNITION

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Read all the instructions contained in this manual. Keep this

manual in a safe place, so that the information is available at

all times. If you give this patio heater to another person, make

sure to provide these operating instructions. Basic safety

precautions should always be followed when using the patio

heater.

Notice the personal safety alert symbol mused in this

manual to draw your attention to a WARNING given along

with the particular operating instruction. This means that

the operation requires special ATTENTION, CAUTION, and

AWARENESS.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

mFOR OUTDOOR USE ONLY

(outside any enclosure)

mDANGER! CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide which has no

odor. Using it in an enclosed space can kill you. Never use this

appliance in an enclosed space such as a camper, tent, car or

home.

mWARNING! Improper installation, adjustment,

alteration, service or maintenance can cause property

damage, injury or death. Read the installation, operating

and maintenance instructions thoroughly before installing or

servicing this equipment.

mDANGER! If you smell gas:

1. Shut o gas to the appliance.

2. Extinguish any open ame.

3. If odor continues, keep away from the appliance and

immediately call your gas supplier or re department.

mWARNING! If the information in this manual is

not followed exactly, a re or explosion may result causing

property damage, personal injury, or loss of life.

mWARNING! Do not store or use gasoline or other

ammable vapors and liquids in the vicinity of this or any other

appliance. An LP-cylinder not connected for use shall not be

stored in the vicinity of this or any other appliance.

mWARNING!

1. The installation must conform with local codes or, in the

absence of local codes, with the National Fuel Gas Code,

ANSI Z223.1/NFPA 54, NFPA58 Natural Gas and Propane

Installation Code, CSA B149.1, or Propane Storage and

Handling Code, B149.2

2. The heater, when installed, must be electrically grounded

in accordance with local codes or, in the absence of local

codes, with the National Electrical Code, ANSI/NFPA 70,

or the Canadian Electrical Code, CSA C22.1.

3. Prior to use, check if any part is damaged, such as hoses,

regulators, pilot or burner. If any of the parts are damaged,

do not use the heater. Please contact the Snow Joe®+

Sun Joe®customer service center at 1-866-SNOWJOE

(1-866-766-9563).

4. All leak tests should be done with a soapy solution.

NEVER USE AN OPEN FLAME TO CHECK FOR

LEAKAGE.

5. Children and adults should be alerted to the hazards of

high surface temperatures and should stay away to avoid

burns or clothing ignition.

6. Young children should be carefully supervised when they

are in the area of the heater.

7. Clothing or other ammable materials should not be hung

from the heater, or placed on or near the heater.

8. Any guard or other protective device removed for

servicing the heater must be replaced prior to operating

the heater.

9. Installation and repair should be done by a qualied

service person. The heater should be inspected before

use and at least annually by a qualied service person.

10. Frequently clean this appliance. It is imperative that

the control compartment, burners and circulating air

passageways of the heater be kept clean.

11. Keep the appliance area clear and free from combustible

materials, gasoline and other ammable vapors and

liquids.

12. Do not obstruct the ow of combustion and ventilation air.

13. Keep the ventilation opening(s) of the cylinder enclosure

free and clear from debris.

14. This appliance shall be used only in a well ventilated

space and shall not be used in a building, garage or any

other enclosed area.

15. This appliance should be installed with shelter no more

inclusive than:

• With walls on all sides, but with no overhead cover.

• Within a partial enclosure which includes an overhead

cover and no more than two side walls. These side

walls may be parallel, as in a breezeway, or at right

angles to each other.

• Within a partial enclosure which includes an overhead

cover and three side walls, as long as 30 percent

or more of the horizontal periphery of the enclosure is

permanently open.

16. This appliance requires 20 lb (9 kg) LP-gas supply

cylinder. Disconnect the cylinder when the appliance is

not in use.

17. Storage of the appliance indoors is permissible only if the

cylinder is disconnected and removed from the appliance.

18. A cylinder must be stored outdoors in a well ventilated

area out of the reach of children. A disconnected cylinder

must have dust caps tightly installed and must not be

stored in a building, garage or any other enclosed area.

19. Only use this appliance with the equipped pressure

regulator and hose assembly. Replace only with pressure

regulators and hose assemblies with those specied by

the appliance manufacturer.

20. Do not store a spare LP-gas cylinder under or near this

appliance.

21. Never ll the cylinder beyond 80 percent full.

22. Do not clean the heater with cleaners that are combustible

or corrosive.

23. Place the dust cap on the cylinder valve outlet whenever

the cylinder is not in use. Only install the type of dust cap

on the cylinder valve that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage

of propane.

24. Do not use the cylinder tank of this heater for storage.

Certain materials, when stored under the heater, will

be subjected to radiant heat and could be seriously

damaged.

25. Inspect the visible portion of the hose before each use

and inspect the entire hose assembly at least annually.

Know Your Outdoor Patio Heater

Read the owner’s manual and safety rules carefully before using your outdoor patio heater. Compare the illustration below to

the actual unit in order to familiarize yourself with the location of the various parts and hardware. Save this manual for future

reference.

Hardware Pack Contents

Phillips Head Bolt

M6x10 | Qty.12

Washer

6mm | Qty.18

Reector Stud

M6x70 | Qty.3

Hexagon Socket Head Bolt

M6x14 | Qty.8

Cap Nut

M6 | Qty.15

CPole Screw

M5x12 | Qty.6

Wheel Screw

M6x20 | Qty.2

1. Heat reector

2. Emitter screen

3. Burner assembly

4. Lighting knob

5. Upper pole

6. Lower pole

7. Bar table

8. Cylinder tank door

9. Cylinder securing wire

10. Wheel assembly

11. Door latch

12. Propane hose connector

13. Propane hose regulator

14. Propane hose

15. Cylinder tank

16. Observation window

BACK

Technical Data

Heater Fuel Type ....................................... Liquid propane gas

Adjustable Heat Output .................. 25,000 BTU - 48,000 BTU

Coverage Area ...................................... 250 sq. ft. | 9 ft. radius

(23.3 m2| 2.7 m radius)

Runtime Max ............................................... High setting: 4 hrs

50% load per standard 20 lbs tank Low setting: 7 hrs

Dimension ........................................... 32.85 in.(D) x 90.6 in.(H)

(83 cm x 230 cm)

Propane Hose Length .......................................... 4.6 ft (1.4 m)

Injector Diameter ....................................... 0.846 in. (2.15 mm)

Manifold Pressure ................................................... 11 in. W.C.

Max Gas Supply ..................................... 250 PSI (1723.7 kPa)

Min Gas Supply ................................................. 5 PSI (35 kPa)

for Input Adjustment

Net Weight ....................................................... 28.7 lbs (13 kg)

Unpacking

NOTE: Before assembly, make sure that all of the parts and

hardware listed below are present. If any part is missing or

damaged, do not attempt to assemble the product. Contact

the Snow Joe®+ Sun Joe®customer service department at

1-866-SNOWJOE (1-866-766-9563).

Parts

1. Reector center cap 2. Reector panel (4)

3. Burner assembly 4. Upper pole

5. Lower pole 6. Deck ring

7. Cylinder tank 8. Cylinder securing wire

9. Wheel assembly

Hardware

A. M6x10 Phillips head bolt (12)

B. 6 mm plain washer (18)

C. M6 cap nut (15)

D. M6x70 reector stud (3)

E. M6x14 Hexagon socket head bolt (8)

F. M5x12 pole screw (6)

G. M6x20 wheel screw (2)

Assembly

Tools Required (Not included):

• Adjustable open end wrench

• Phillips screwdriver

Choose a soft and level location for assembly. Remove all

parts from the packaging, and check for missing parts.

1. Line up holes on the bracket of the wheel assembly with

the corresponding holes on the base of the cylinder tank,

then insert the M6x20 wheel screws (G) through holes and

tighten to secure. Be sure the wheel assembly is parallel

to the base (Fig. 1).

Hardware Required

2. Place the lower pole in the middle of the bar table, x with

4 M6x14 hexagon socket head bolts (E). Slide the deck

ring down the lower pole to cover the connection part and

the bolts (Fig. 2).

Hardware Required

ITEM DESCRIPTION QTY.

GWheel screw (M6x20) 2

Fig. 1

Wheel assembly

Wheel screw

(M6x20)

Cylinder tank

ITEM DESCRIPTION QTY.

EHexagon socket head bolt (M6x14) 4

3. Attach the 4 reector panels together using 4 M6x10

Phillips head bolts (A) and 4 plain washers (B). Secure

with 4 cap nuts (C), as shown (Fig. 3).

Hardware Required

4. Attach the assembled reector panels with the reector

center cap using 8 M6x10 Phillips head bolts (A) and 6

plain washers (B). Secure with 6 cap nuts (C) (Fig. 4).

Hardware Required

5. Attach the 3 reector studs (D) and 3 plain washers (B) to

the top of the burner assembly. Tighten the reector studs

(Fig. 5)

Hardware Required

Fig. 2

Lower pole

Hexagon socket

head bolt

(M6x14)

Deck ring

Slide down

ITEM DESCRIPTION QTY.

APhillips head bolt (M6x10) 4

BPlain Washers (6 mm) 4

CCap nut (M6) 4

Fig. 3 Reector panels

Phillips head bolt (M6x10)

Plain

washer Cap nut

ITEM DESCRIPTION QTY.

APhillips head bolt (M6x10) 8

BPlain Washer (6 mm) 8

CCap nut (M6) 8

Assembled

reector panels

Fig. 4 Reector center cap

Phillips head bolt (M6x10)

Cap nut Plain washer

ITEM DESCRIPTION QTY.

DReector stud (M6x70) 3

BPlain Washer (6 mm) 3

Fig. 5

Reector stud

Plain washer

Burner

assembly

6. Attach the reector assembly to the burner assembly.

Place a plain washer (B) over the threaded end of each

reector stud (D) sticking out through reector assembly

and secure with cap nuts (C). Note: Do not overtighten

(Fig. 6).

Hardware Required

7. Insert the propane hose that is connected with the burner

assembly into the upper pole. Secure with 4 M6x14

hexagon socket head bolts (E) (Fig. 7)

Hardware Required

8. Connect the upper pole assembly with the lower pole

assembly as shown. Fix with 6 M5x12 pole screws (F)

(Fig. 8).

Hardware Required

9. Fill sand into the cylinder tank base through the hole in the

middle, as shown (Fig. 9).

NOTE: Purchase sand separately at your local garden

center or hardware store.

10. Insert the ends of the cylinder securing wire into the two

small holes on the tank base (Fig. 10).

ITEM DESCRIPTION QTY.

CCap nut (M6) 3

BPlain Washer (6 mm) 3

Fig. 6

Reector

assembly Plain washer

Burner

assembly

Cap nut

Reector stud

ITEM DESCRIPTION QTY.

EHexagon socket head bolt (M6x14) 4

Fig. 7

Hexagon socket

head bolt

(M6x14)

Burner

assembly

Propane

hose

Upper

pole

ITEM DESCRIPTION QTY.

FPole screw (M5x12) 6

Fig. 8

Upper pole

assembly

Lower pole

assembly

Pole screw

(M5x12)

Fig. 9

Fill the hole

with sand

until it's full.

Using the Propane Tank

This appliance requires 20 lbs (9 kg) LP-gas supply cylinder.

(not included). Propane is highly ammable and may

ignite unexpectedly when mixed with air. Follow the safety

instructions below when handling the propane cylinder:

• The cylinder used with this heater must be constructed and

marked in accordance with the Specications for LP-gas

cylinders of the U.S. Department of Transportation (DOT);

or the Standard for Cylinders, Spheres and Tubes for

Transportation of Dangerous Goods and Commission, CAN/

CSA-B339, as applicable;

• The cylinder used with this heater must be provided with

a listed overlling prevention device; and provided with a

cylinder connection device compatible with the connection

for the appliance;

• Keeping the ventilation opening(s) of the cylinder enclosure

free and clear from debris;

• Do not store a spare LP-gas cylinder under or near this

appliance;

• Never ll the cylinder beyond 80 percent full;

• Place the dust cap on the cylinder valve outlet whenever

the cylinder is not in use. Only install the type of dust cap

on the cylinder valve that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage of

propane.

mWARNING! A dented, rusted or damaged

propane cylinder may be hazardous and should be checked

by your propane supplier. Never use a propane cylinder with a

damaged valve connection.

Connect the Propane Tank

mWARNING! Never connect an unregulated

propane cylinder to the heater.

1. Open the tank door and place a cylinder inside the tank.

Let it sit in securely. Use the securing wire to secure the

gas cylinder, like shown (Fig. 11).

2. Connect the propane hose connector with the propane

cylinder. Turn clockwise to secure (Fig. 12).

3. Close the tank door. Lock the door latch

Leakage Test

All connections of this patio heater have been checked at the

factory for leakage. However, in transportation and handling

some connections may have loosened. It's recommended to

run the leakage test every time before using and after parts

replacement.

mWARNING!

• Do not use an open ame to check for leakage.

• Do not smoke during testing.

• Do not test indoors.

• A leak check must be performed whenever the propane

cylinder is replaced.

NOTE: Use only the pressure regulator supplied with this patio

hearer. Replace it with those specied by the manufacturer

only.

Fig. 10

Cylinder

securing wire

Insert in the

small holes

Fig. 11

Propane

cylinder

Cylinder

securing wire

Tank door

Fig. 12

Propane

hose

Propane

hose

connector

1. Make leakage solution by mixing 1 part liquid dish soap

and 3 parts water.

2. With the cylinder connected to the hose, spoon or brush

several drops (or use squirt bottle) of the solution onto the

connections along the hose, regulator and cylinder

(Fig. 13).

3. Open the propane cylinder valve. Inspect the connections

and look for bubbles.

4. If no bubbles appear, the connection is safe. If bubbles

appear, there is leakage. Loosen and re-tighten this

connection. If there is still a leak, turn o the cylinder

and contact the Snow Joe®+ Sun Joe®customer service

center at 1-866-SNOWJOE (1-866-766-9563).

At least once a year, a complete inspection of the entire gas

path components should be performed by a professional

technician.

Operation

mWARNING! Do not attempt to operate the heater

until you have read and understand all precautions in this

manual. Make sure all assembly is complete and leakage test

have been performed. Failure to do so can result in death,

serious personal injury, or property damage.

Before Turning on the Gas Supply

1. The heater is designed and approved for OUTDOOR USE

ONLY. DO NOT use it inside a building, garage, or any

other enclosed area.

2. Make sure the surrounding areas are free of combustible

materials, gasoline, and other ammable vapors or liquids.

3. Ensure that there is no obstruction of air ventilation.

Ensure all gas connections are tight and there's no leak.

4. Be sure any component removed during assembly or

servicing is replaced and fastened prior to starting.

Lighting the Heater

mWARNING!

• Heater should be thoroughly inspected before each use,

and by a qualied service person at least annually. If

relighting a hot heater, always wait at least 5 minutes.

• Before lighting, inspect the hose assembly for evidence of

excessive abrasion, cuts, or wear. Suspected areas should

be leak tested. If the hose leaks, it must be replaced prior

to operation. Only use the replacement hose assembly

specied by manufacturer.

mWARNING! Follow the instruction below to light

the heater. Improper lighting operation may cause personal

injury or property damage.

1. Connect the propane cylinder and perform the leakage

test as instructed above.

2. Make sure the lighting knob is in the OFF position

(pointing to the black dot). Open the propane cylinder

valve.

3. Push in the lighting knob and turn it counterclockwise to

the LOW position (pointing to the small red dot). This will

light the burner. If needed, keep depressing and turning

the lighting knob counterclockwise until the burner is lit.

You will hear one click when the burner is lit (Fig. 14).

4. Once the burner is lit, keep the knob depressed for 30

seconds. Then release the lighting knob.

5. If burner does not stay lit, repeat steps 3 and 4 after 5

minutes.

6. If burner still does not stay lit, then:

i. Push in the lighting knob and turn it counterclockwise to

the "LOW" position.

ii. Keep depressing the lighting knob, use a long stem

lighter to light the burner through the ignition hole on

the emitter screen (Fig. 15).

Fig. 13

Fig. 14

OFF LOW HIGH

Lighting knob

iii. Repeat step 4.

7. After the burner is lit, adjust the temperature by rotating

the lighting knob. Turn the lighting knob counterclockwise

to "HIGH" position (pointing to the big red dot). If you want

a lower temperature, turn the control knob clockwise to

the "LOW" position (pointing to the small red dot) (Fig. 14).

mWARNING! FOR YOUR SAFETY

If at any time you are unable to light burner and smell gas, wait

at least 5 minutes to allow gas to dissipate before attempting

to light the gas appliance again.

Flame Characteristic

The ame can be checked through the emitter screen during

operation. The normal ame should be mostly blue with yellow

tip. Abnormal ame characteristics include:

• The ame extends beyond the emitter screen.

• Black spots can be seen accumulating on the emitter

screen or the reector assembly.

If any of the above situations appears, turn o the heater

immediately and contact the Snow Joe®+ Sun Joe®customer

service department at 1-866-SNOWJOE (1-866-766-9563).

The heater should not be used again before it's serviced or

repaired.

Operation Tips

mWARNING! When use the heater for the rst

time, avoid inhaling fumes emitted from the heater. The fumes

contain smoke and odor from the burning of oils used in

manufacturing. The fumes will dissipate after approximately 30

minutes. The heater should NOT produce thick black smoke.

mWARNING! Do not touch or move the heater for

at least 45 minutes after use. Allow the heater to cool down

completely.

mCAUTION! Items above, beside or under this

heater while in use will be subject to radiant heat and could be

seriously damaged.

mWARNING! This heater must be placed on level,

rm ground.

mWARNING! Never operate in an explosive

atmosphere. Keep away from areas where gasoline or other

ammable liquids or vapors are stored or used.

• This heater is designed for the heating of outdoor patios,

decks, spas, pools and open work areas. Always make

sure that adequate fresh air ventilation is provided. Follow

the spacing tolerances shown in the following gure at all

times (Fig 16).

• When initially turned on, it's normal for the heater to

produce some noise. If this happens, turn the lighting

knob to the LOW position (pointing to the small red dot).

Wait for a while and then adjust the knob to the desired

temperature.

• When the heater is on, the emitter screen will become

bright red due to the intense heat. The blue ame can be

seen through the emitter screen.

• If the ame appears to be mostly yellow or there's heavy

black smoke produced by the heater, there may be an

obstruction of airow. If this happens, turn o the heater

and contact the Snow Joe®+ Sun Joe®customer service

department at 1-866-SNOWJOE (1-866-766-9563).

• If the ame appears to be very small, this may be caused

by the insucient pressure. Change or rell the propane

cylinder.

• If the heater extinguished accidentally, rotate the lighting

knob to the OFF position (pointing to the black dot), wait

for 5 minutes and follow the instruction in Lighting the

Heater section from step 2 to relight the heater.

NOTE: Always wait for 5 minutes before relighting.

Extinguishing

1. Push in and turn the lighting knob counterclockwise to

OFF position (pointing to the black dot) (Fig. 14).

2. Close the propane cylinder valve when appliance is not

in use. Disconnect and remove the cylinder if the heater

needs to be transported or stored.

Fig. 15

Emitter

screen

Ignition

hole

91 cm

61 cm

Fig. 16

NOTE: After use, it's normal for the emitter screen to have

some discoloration.

mWARNING! Gas appliance will be hot after

use. DO NOT touch or move gas appliance for at least 45

minutes after use.

In The Event of Gas Leakage:

1. Turn the lighting knob to OFF position.

2. Close the propane cylinder valve.

3. Wait at least 5 minutes to allow gas to dissipate.

4. If odor continues, immediately call gas supplier.

Maintenance

To enjoy years of outstanding performance from the patio

heater, make sure you perform the following maintenance

activities on a regular basis.

mWARNING! DO NOT touch or move gas appliance

for at least 45 minutes after use. Allow it to cool before

touching.

Cleaning

This patio heater should be cleaned on a regular basis to

promote safer experiences and longer product life.

DO NOT attempt to clean this heater until it is COMPLETELY

extinguished and COMPLETELY cooled down.

1. Keep exterior surfaces clean.

2. Use warm soapy water for cleaning. Never use a

ammable or corrosive cleaning agent.

3. While cleaning your unit, be sure to keep the area around

the heater dry at all times. If any part of the gas control

system is exposed to water in any way, do NOT use it. It

must be replaced.

General Maintenance

1. Keep the work area free and clean from combustible

materials, gasoline and other ammable vapors and

liquids. Do not obstruct the ow of combustion and

ventilation air. Keep the ventilation opening(s) of the

cylinder enclosure free and clear from debris.

2. Turn on the heater as instructed before, and visually check

burner ames. The ames should be primarily blue with

yellow tip.

3. Remove the Hexagon socket head bolts (M6x14) used

to secure the burner assembly and the upper pole. Take

out the burner assembly and check if there are cracks

or worn sections on the propane hose. If yes, do not use

the heater and contact Snow Joe®+ Sun Joe®customer

service at 1-866-SNOWJOE (1-866-766-9563) for

assistance.

NOTE: If used in a salt-air environment (such as near an

ocean), corrosion occurs faster than normal. Frequently

check for corroded areas and repair them promptly.

4. Spiders and insects tend to nest inside the heater. This

can cause damage to the heater and render it unsafe to

use. At least once a year, the unit should be inspected for

the presence of spiders, spider webs or other insects.

5. Air ow must be unobstructed. Keep controls, burner,

and circulating air passageways clean. Signs of possible

blockage include:

i). Gas odor with extreme yellow ame.

ii). Heater does NOT reach the desired temperature.

iii). Heater glow is excessively uneven.

iv). Heater makes popping noises.

6. Carbon deposits may create a re hazard. Clean the

reector and the emitter screen with warm soapy water if

any carbon deposits is seen.

Annual Propane Hose Leakage Test

All connections on the patio heater have been adjusted and

tightened at the factory, however, in case any connection is

loosened during long term use, it's recommended that users

test the propane hose connection at least once a year.

mWARNING!

• Do not use an open ame to check for leakage.

• Do not smoke during testing.

• Do not test indoors.

1. Make leakage solution by mixing 1 part liquid dish soap

and 3 parts water.

2. With the cylinder connected to the hose, remove the

observation window panel located opposite to the lighting

knob (Fig. 18).

Fig. 17

Burner assembly

Upper pole

Check for cracks or

worn parts

Table des matières

Autres manuels sunjoe Chauffage

sunjoe

sunjoe SJPH1500E Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur

sunjoe SJPPH48 Manuel utilisateur

Manuels Chauffage populaires d'autres marques