Sundirect SC-Plus Instructions d'installation

Installation & Operation Instructions

Version: SDUM-210628

SC-Plus

Smart Infrared Space Heater

2

Language

Page

P3-P9

P10-P16

1. Notice to Purchaser

Thanks for purchasing this Sundirect infrared heater. We hope you enjoy this innovative

technology and that this product will bring a pleasant atmosphere to your home.

Please read these instructions carefully and keep safe for future use. Failure to comply with these

instructions will void your warranty. Do not disassemble or tamper with the product at any time!

Please pay special attention to the safety instructions and use the heater according to these

instructions. Sundirect Technology Ltd. shall not be liable for any damage or loss occurred resulting

from failure to follow these instructions.

2. General Introduction

Sundirect Infrared heaters heat objects instead of the air, making this heater much more efﬁcient

than traditional convection heaters.

The Sundirect Plus series represents a new generation of infrared panel heaters, equipped with a

built-in thermostat receiver inside of the junction box (Artcile Number: Receiver01) on the backside

of the panel. It needs to be used in conjunction with the Sundirect control system - Smart 1.0/ Smart

1.0Pro or Smartplug (NOT included in the box) - in order to meet the Ecodesign legislation of the

EU/EC Directive 2009/125/EC.

You may ﬁnd detailed speciﬁcations and instructions in the manual of Smart 1.0/1.0Pro or SmartPlug

separate from this manual.

This product complies with the LVD guideline 2014/35/EU and the EMC guideline 2014/30/EU and

meets the following standards:!

EN 60335-1:2012/A2:2019

EN 60335-2-30:2009/A12:2020

EN 62233:2008

AfPS GS 2019:01 PAK

EN 55014-1:2017/A11:2020

EN 55014-2:2015

EN IEC 61000-3-2:2019

EN 61000-3-3:2013/A1:2019

2014/53/EU 《RED 》(LVD 2014/35/EU & EMC 2014/30/EU)

2011/65/EU, 2015/865/EU《RoHS 》

2015/1188/EC 《Erp 》

3

Read the installation and operating instructions completely before

starting any installation works and save the instructions for later use.

3. Safety instructions

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

3.1 Product related safety warnings

•Sundirect infrared heaters operate at a surface temperature of around 350°C when wall mounted.

Do NOT touch the heater when switched on.

•Prolonged contact may cause injuries or burns.

•Do NOT cover the heater with anything. Covering may cause overheating and can result in ﬁre.

•The heater should NOT be used to dry textiles and no objects shall be placed or leaned against

the heater.

•Keep a distance of at least 40cm in the front and 20cm on the sides to any object, wall or ceiling.

Failure to do so will cause heat to build up behind the heater and will void your warranty.

3.2 Dangers for children and persons with limited abilities

•Children or persons with limited physical, mental or sensory abilities shall not be operating,

switching on, plugging in, regulating or cleaning the heater.

•Small children should be kept away from the heater unless constantly supervised.

•Do NOT operate the heater in small rooms when occupied by people not capable of leaving the

room by themselves. The surface of the heater can reach a surface temperature of up to 95°C,

keep out of reach of children and disabled persons.

•Keep away babies and children from all packaging material such as plastic bags to avoid danger

of suffocation.

3.3 Electric safety directions

•When installing, repairing or servicing the heater it must be turned off and disconnected from

power. Before installation please check if the heater is free of damages.

•If the heater or the power cord is damaged in any form do NOT use the heater and contact your

Sundirect dealer for repair or replacement. Repairs, maintenance or any changes must be carried

out by an authorized Sundirect dealer.

•Do NOT attempt to repair the heater by yourself, this will void your warranty.

•If the heater has been dropped do NOT operate it and contact your Sundirect dealer to make sure

it is free of any damages.

4

•Sundirect heaters are designed to operate at 220-240V, 50Hz AC. If your supply mains do not

comply with this, do NOT use the heater.

3.4 Water Proof

Sundirect infrared heaters have different IP ratings on different models. Please make sure to only

install heaters with IP44 rating in humid rooms. Please carefully check the speciﬁcations to conﬁrm if

your heater is suitable for installation in humid rooms.

Sundirect shall not be liable for any injuries or damages resulting from inadequate mounting or

incorrect positioning close to water sources.

4. How to care for your Sundirect heater

4.1 Cleaning

Always unplug your heater and let it cool down completely before cleaning. Never dip into water

and never splash water on it. Clean the heater with a soft damp cloth. For glass models such as the

GD-Plus, MD-Plus series use a soft cloth and glass cleaner. Never use a wet cloth and make sure to

dry the heater when clean with a dry cloth. Do not use any abrasive materials, solvents or harsh

cleaning sponges as this could cause scratches or other irreparable damage. Before operating the

heater again it must be completely dry.

4.2 Using/Working

•Please note that the heater may discolour with use. This is due to airborne pollution and is not a

fault. If you wish to add a picture print to your heater please contact a Sundirect dealer. Do not

cover your heater with a picture foil and do not paint or print the heater yourself. This might cause

damage to the heating element and will void your warranty.

•This heater might emit a slight smell during ﬁrst time use. This is normal due to the high surface

temperature of the material. The smell will disappear after few times using the heater.

•When turning on or off the heater, the heater might have a small clicking noise, this is normal due

to material expansion.

4.3 Repair

Repairs must be carried out by authorised Sundirect dealers or by Sundirect directly. If you attempt

to alter the product or to proceed with any repairs yourself it will void your warranty.

4.4 Disposal

Sundirect infrared heaters are electric appliances and therefore electric waste. At the

end of its working life please dispose the heater in accordance with local regulations

concerning electric waste.

5

5. Installation & Operation Guide

5.1 Description

This heater is equipped with our

built-in thermostat receiver -

Receiver01 - on the backside of the

panel. Before starting the installation,

we recommend you to pair the

receiver to our remote control as a

ﬁrst step. Follow the guide bellow to

ﬁnish the pairing to the Smart control

system (e.g. Smart 1.0, Smart 1.0Pro

or Smartplug).

On the right see the drawing of the

signal lights and button of

Receiver01.

1) Pair status signal light (green light)

2) Heating status signal light (red light)

3) “P” button

4) Power switch

5.2 Pairing to Sundirect Smart control system

Step1: Plug your heater to an electricity outlet, switch the Power switch of Receiver01 on, double

press the “P” button and the “Pair signal light” will start to ﬂashing and ready for pairing.

Step2: Power-off the remote control Smart 1.0/Smart 1.0Pro/Smartplug, long press the “SET” button.

The “PAIR” signal will show on the screen of the remote control. Wait until the “Pair signal light”

stop ﬂashing and glow green to ﬁnish the pairing. Now the pairing process is ﬁnished and the

Receiver01 will only be commanded by the Smart controller.

Note: After the paring process and once Receiver01 and Smart 1.0/Smart 1.0Pro/Smartplug are

paired, the pair signal light will always be on and the Receiver01 will be only commanded by the

Smart 1.0/Smart 1.0Pro/Smartplug. One Receiver01 can only pair to one controller, however, One

controller can be paired to several Receiver01 if they are in the same room.

5.3 Extra Safety Protection:

The heater is equipped with the Sundirect “Extra Safety Protection” function, which will automatically

turn off the heater if it lost the signal from the Smart controller for more than one hour. And it will

be automatically connected once the Smart controller is within the communication distance.

6

5.4 Bypass mode

Long-press the “P” button on Receiver01 until the “Pair signal light” off and the “Heating status

signal light “on, the panel will be reset to bypass mode. On the bypass mode, the Receiver01 is

disabled and the panel is connected directly to the electricity.

5.5 Installation

7

Note:

•Note: The kit supplied in the package is

designed for mounting on a solid ceiling.!If

mounted onto other types of ceilings, you will

need appropriate ﬁxings (not supplied).!Please

make sure the ceiling is safe to mount.!We

highly recommend to have the panel installed

by a qualiﬁed electrician or installer authorized

by Sundirect.!

•The SC series is a hot temperature infrared

heater. It has a surface temperature of

300-350°C when in operation. Please pay

special attention and mount them out of reach.

On the left, see the drawing of the mounting

requirements. When installing the space heater

to a ceiling or wall please make sure to keep a

distance of at least 20cm to the neighbouring

walls or ceilings and a minimum distance from

the ﬂoor of 2.2m.

•The heater is designed to be used in outdoor

areas with minimal air movement. If used in

areas with strong winds, please note that the

heating performance might decrease. As a

solution, we suggest to mount the heater closer

to the objects you wish to heat to achieve a

better performance. Please make sure the

heater is protected from rain, it can withstand

splash water only.

 

󾺿



The mounting kit included in this box contains:

Part A: 2x mounting handles Part B: 2x mounting handles Part C: 8x screws Part D: 8x wing nuts Part

E: 4x wall/ceiling anchors !

Step 1: Slide the mounting handles (part A) into the rail on the back of the heater from the opposite side of the

cables. Make sure both handles face into the same direction.

Step 2: Drill four holes into the wall/ceiling, two for each mounting handle (part B). Use the mounting handles as

stencils and level them to make sure the heater will hang straight on the wall/ceiling. You can chose the distance

between the two handles to your liking but make sure the distance doesn't exceed the length of the heater.

Remove the nut form the wall/ceiling anchors (part E) and place the wall/ceiling anchors into the drilled wholes.!

Step 3: Place the mounting handles (part B) onto the wall/ceiling anchors and secure them with the wall/ceiling

anchor’s nut (part E) using a wrench.!

Step 4: Place the heater against the wall/ceiling and attach each of the mounting handles that are mounted on the

wall (part B) with the mounting handles attached on the heater (part A). Secure them with two screws (part C) and

two wing nuts (part D) on each side. Chose the mounting holes according to the way you want the heater to be

directed.!!

Step 5: Finally secure the mounting handle (part A) to the heater using two screws and two wing nuts on each

side. Make sure everything is safely mounted and secured.!

8

   

                   

   

   

   



   

   

   

   

   

   

   

   

   

   

6. Technical speciﬁcations:

Panels covered by these instructions are listed in the table below.

7. Warranty

Sundirect offers a 5 year manufacturing warranty on the heating panel and 2 year manufacturing warranty on the

control system (including Receiver01, Smart 1.0/Smart 1.0Pro/Smartplug and so on). You can ﬁnd the serial

number on the last page of this user manual. Please always keep this manual in case of future warranty claims.

Within the warranty period from date of purchase, Sundirect will repair or replace your heater where the fault is

due to defects in workmanship or materials. Please contact your local Sundirect dealer in the event of a warranty

claim and return the heater together with proof of purchase.

The warranty covers the repair or replacement of the heater only and Sundirect shall not be liable for any other

occurring costs such as installation cost or any other consequential losses however incurred. Please note that

tampering with or opening the heater in any way will void your warranty. The removal of the serial number on the

back of the heater will also void this warranty. All labels on the back of the heater shall not be removed.

Any damages to the heater caused by the user are not covered by this warranty. This includes scratches on the

surface or the frame. Sundirect is not responsible for any damages, losses or injuries due to ingress of water or

moisture, accidental damage, mishandling, external impact, repairs or adjustment by unauthorized persons or

failure to follow the correct safety, maintenance and installation precautions stated in this manual.

Model

Power

Size

Weight

Mounting

Build-in

thermostat

receiver

IP Protection

SC1800-Plus

1800W

137*16*12cm

7Kg

Wall/Ceiling

Yes

IP44

SC2400-Plus

2400W

157*16*12cm

8Kg

Wall/Ceiling

Yes

IP44

9

1. Anmerkungen

Vielen Dank, dass Sie sich für Sundirect entschieden haben. Wir hoffen Sie sind zufrieden

mit der innovativen Technologie und der angenehmen Atmosphere die dieses Produkt

zu Ihnen nach Hause bringt.

Zu Ihrer eigenen Sicherheit lesen Sie sich bitte diese Betriebsanleitung sorgfältig durch. Falls Sie die

Anweisungen in dieser Anleitung nicht befolgen kann die Produktgarantie verfallen. Bitte nehmen

Sie keine Änderungen an dem Produkt vor! Beachten Sie bitte die Sicherheitshinweise. Sundirect

kann nicht für Verlust oder Schäden haftbar gemacht werden, die aus Nichtbeachtung dieser

Anweisungen entstehen.

2. Allgemeines

Sundirect Infrarotheizungen erwärmen Objekte statt der Luft, was diese Heizung wesentlich

efﬁzienter macht als traditionelle Konvektionsheizungen.

Die Sundirect Plus Serie ist eine neue Generation von Infrarotheizpaneelen, ausgestattet mit einem

eingebauten Thermostatempfänger in der Anschlussdose (Artikelnr.: Receiver01) auf der Rückseite

des Paneels. Es muss zusammen mit einem Sundirect Steuerungssystem - Smart 1.0/Smart1.0Pro

oder Smartplug (nicht im Lieferumfang enthalten) - genutzt werden um die Ökodesign Richtlinie

der EU - EC Richtlinie 2009/125/EC- zu erfüllen.

Sie können die technischen Details und Anweisungen in der Bedienungsanleitung von Smart

1.0/1.0Pro/plug ﬁnden (separat von dieser Anleitung).

Dieses Produkt entspricht der LVD 2014/35/EU und der EMC Richtlinie 2014/30/EU und erfüllt die

folgenden Standards:

EN 60335-1:2012/A2:2019

EN 60335-2-30:2009/A12:2020

EN 62233:2008

AfPS GS 2019:01 PAK

EN 55014-1:2017/A11:2020

EN 55014-2:2015

EN IEC 61000-3-2:2019

EN 61000-3-3:2013/A1:2019

2014/53/EU 《RED 》(LVD 2014/35/EU & EMC 2014/30/EU)

2011/65/EU, 2015/865/EU《RoHS 》

2015/1188/EC 《Erp 》

10

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Sundirect Chauffage

Sundirect

Sundirect Tower1000-Pro Instructions d'installation

Sundirect

Sundirect IC Series Manuel utilisateur

Sundirect

Sundirect TH400 Instructions d'installation

Sundirect

Sundirect Hybrid500-Pro Instructions d'installation

Sundirect

Sundirect Hybrid750-Pro Instructions d'installation

Sundirect

Sundirect Tower500-Pro Instructions d'installation

Sundirect

Sundirect OC2000 Instructions d'installation

Sundirect

Sundirect Stone600-Pro Instructions d'installation

Sundirect

Sundirect BC004 Manuel utilisateur

Sundirect

Sundirect PE-Plus Instructions d'installation

Sundirect

Sundirect TH400 Instructions d'installation

Sundirect

Sundirect Tower1000-Pro Instructions d'installation

Sundirect

Sundirect OC2500-Pro Instructions d'installation

Sundirect

Sundirect Hybrid500-Pro Instructions d'installation

Sundirect

Sundirect TH600-PRO Instructions d'installation

Sundirect

Sundirect PE380-Plus Instructions d'installation

Sundirect

Sundirect Footwarmer220-Pro Instructions d'installation

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur