SunDash Radius 252 Manuel utilisateur
1
2
252
Depth: 50" Door Closed, 63” Door Open
Width : 39.5"
Height: 90"
Shipping Weight: 1325 Lbs.
No. of Lamps : 52
Electrical : 39 AMPS @ 225 Volts, Three Phase or 63 Amps @ 225 Volts, Single Phase
Circuit Requirements: 120/225V 3 Phase 50 Amp or 120/225V Single Phase 80 Amp
DANGER - ULTRAVIOLET RADIATION. FOLLOW INSTRUCTIONS. AVOID OVEREXPOSURE. AS
WITH NATURAL SUNLIGHT, OVEREXPOSURE CAN CAUSE EYE AND SKIN INJURY AND
ALLERGIC REACTIONS. REPEATED EXPOSURE MAY CAUSE PREMATURE AGING OF THE SKIN
AND SKIN CANCER. WEAR PROTECTIVE EYEWEAR; FAILURE TO MAY RESULT IN SEVERE
BURNS OR LONG-TERM INJURY TO EYES.
MEDICATIONS OR COSMETICS MAY INCREASE YOUR SENSITIVITY TO THE ULTRAVIOLET
RADIATION. CONSULT PHYSICIAN BEFORE USING SUNLAMP IF YOU ARE USING MEDICATIONS
OR HAVE A HISTORY OF SKIN PROBLEMS OR BELIEVE YOURSELF ESPECIALLY SENSITIVE
TO SUNLIGHT. IF YOU DO NOT TAN IN THE SUN, YOU ARE UNLIKELY TO TAN FROM THE USE
OF THIS PRODUCT.
THIS UNIT UTILIZES UVA LAMPS. REPLACE ONL Y WITH GENESIS 2000 SHRX FR
78-T12-SHRX-2.
TO OBTAIN THE RECOMMENDED EXPOSURE POSITION OF A MINIMUM USE DISTANCE OF 6"
(152.4 MM) MEASURED WITH A STANDARD RULER, STAND UPRIGHT ON DECAL IN FLOOR OF
UNIT. THE USE OF ANY OTHER POSITION MAY RESULT IN OVEREXPOSURE.
SKIN TYPE
II - FAIR
III - AVERAGE
IV - BROWN
V - DARK BROWN
MAXIMUM EXPOSURE TIME IS 12 MINUTES.
TANNING CAN BEGIN ON A REGULAR BASIS. AN APPEARANCE OF TANNING NORMALLY
APPEARS AFTER A FEW EXPOSURES AND MAXIMIZES AFTER FOUR (4) WEEKS OF
EXPOSURE FOLLOWING THE RECOMMENDED SCHEDULE FOR YOUR SKIN TYPE.
USE PROTECTIVE EYEWEAR, SUPER SUNNIES, WHENEVER THE EQUIPMENT IS ENERGIZED.
READ THE INSTRUCTION BOOKLET BEFORE USING THIS UNIT.
INSTRUCTIONS ACCOMPANYING THIS PRODUCT SHOULD ALWAYS BE FOLLOWED TO AVOID
OR MINIMIZE POTENTIAL INJURY.
“THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR SUNLAMP PRODUCTS UNDER 21 CFR PART 1040.”
WEEK 1
1 ST-3RD
TREATMENTS
2 MIN.
2 MIN.
2 MIN.
2 MIN.
WEEK 2
4TH-6TH
TREATMENTS
5 MIN.
5 MIN.
7 MIN.
7 MIN.
WEEK 3
7TH-10TH
TREATMENTS
8 MIN.
8 MIN.
10 MIN.
10 MIN.
WEEK 4
11TH-15TH
TREATMENTS
10 MIN.
10 MIN.
12 MIN.
12 MIN.
WEEKLY
SUBSEQUENT
TREATMENTS
12 MIN.
12 MIN.
12 MIN.
12 MIN.
Specifications
Recommended Exposure Schedule
3
Mandatory Reading
Always read and follow all instructions for proper usage prior to using any tanning system.
Remember:
1. Follow the exposure schedule in accordance with your skin type. Failure to do so may result
in overexposure.
2. A tanning system is not a toy. You cannot vary the strength of the lamps in your unit.
Should you have any questions regarding the proper use of your tanning system, contact
JK Global Service at:
1-800-445-0624
8:00 a.m. To 5:00 p.m. (CST)
Warnings and Cautions
Certain drugs - particularly those that
produce photosensitivity - may cause
individuals under the influence of this type drug
to experience adverse effects and those people
should avoid exposure to UV sources of all
kinds. Doctors will advise persons taking these
drugs to possible adverse effects.
It is recommended that only one person
at a time should use the tanning system while
in use, and advises using protective eyewear
while taking a tanning session. One pair of
goggles is provided with each sunbed sold.
WARNING
If you have been diagnosed by a physician as being allergic to the sun or are currently taking
photosensitive medications, consult your physician before using the tanning unit.
Occasionally, persons using the tanning
system will experience a slight reddening of
the skin - usually in small patches - after the
second or third session. This redness is often
accompanied by an itching sensation. This
may be nothing more than a heat “rash” caused
by heat from the lamps within the system.
It should go away within approximately
24 hours and should not reappear. This rashing
can be lessened or prevented by applying
moisturizer lotion to the affected area after the
tanning session is completed.
CAUTION
While there is no immediate clinical evidence regarding UV exposure and its effects upon
expectant mothers, it is strongly advised that expectant mothers be discouraged from using the
tanning unit.
4
Care and Cleaning of Your Tanning Unit
After each session is completed, spray the
acrylic surface with specially formulated UVT
(ultraviolet transmitting) acrylic cleaner. Wipe
the surface of the acrylic with a clean cloth.
The acrylic should never be wiped with a dry
cloth because this will generate a slight static
charge which will attract dust. A mild liquid
detergent and water solution can be used
temporarily in place of Acrylic Cleaner.
For maximum efficiency of your tanning unit, periodic cleaning of lamps, reflectors and the inside
of the acrylics is required. Refer to relamping instructions for acrylic removal.
CAUTION: Do not use excessive amounts of water, any abrasive cleaners, or any spray cleaners
that carry label warnings regarding reactions to contact with skin!
DO NOT USE ALCOHOL OR AMMONIA
Electrical Safety:
The tanning unit should be disconnected from the power supply before cleaning of
disinfecting the inside of the acrylic. Avoid water or solution entering the lamp compartment.
Relamping Instructions
CAUTION:
Replacement lamps must comply with CFR21 1040.20
A. Replace only with “Genesis 2000 SHRX FR78-T12 SHRX-2”
B. When Ordering lamps, include model number and serial number.
Disconnect unit from power.
To remove acrylic from Panel D (Door Panel), locate the six (6) 1/4 turn fasteners on the acrylic retainer
strip on the left side of the panel. Using a flat head screwdriver, turn each fastener a 1/4 turn counter
clockwise. You should hear a snap to release the strip. Repeat procedure on the remaining fasteners on
the retainer strip.
Lift edge of the acrylic approximately two (2) inches and slide acrylic to the left to remove.
Twist lamp 1/4 turn to disengage lamp from lampholder . Remove lamp. Repeat procedure for the
remaining twelve lamps in Panel D.
Relamp, clean and replace acrylic sheet. To install acrylic sheet, slide the entire length of the right edge
of the acrylic into the groove between the right rail and the acrylic the acrylic retainer strip. Flush the
acrylic with the groove in the rail, and secure with the lef t acrylic retainer strip. To attach the acrylic
retainer strip, align all six holes in the strip with the six holes in the left rail. Secure strip using a flathead
screwdriver. Turn each fastener clockwise 1/4 turn. You should hear the fastener snap to secure the strip.
Proceed to Panel C (next panel clockwise) and repeat procedures 2 through 5.
Upon completion of all the panels, reconnect unit to power.
1.
2.
3.
4.
5.
6.
7.
5
Exposure Time and Frequencies
Melanin - The brownish pigment produced
by special cells in the base layer of your skin
determines the individual’s tan. As the skin is
exposed to the ultraviolet light, the melanin is
activated and combines with protein cells that
rise to the skin’s surface, thus producing a tan.
The amount of melanin in your body
determines how quickly and dark you t an. The
more melanin produced and exposure time an
individual has, the faster and deeper the
individual will tan. Do not tan more than once in
a 24 hour period.
NOTE
The tan produced by the tanning unit is a deep, rich “cosmetic”tan. However, regardless of how
dark an individual may tan on this system, it will not provide adequate protection against
overexposure to natural sunlight or UVB tanning systems.
SKIN TYPE II - This is the individual that
usually burns easily and severely, tans minimally
or lightly and peels.
SKIN TYPE III - Often referred to as
“AVERAGE” complexion, burns moderately and
tans about average.
SKIN TYPE IV - This individual burns
minimally, tans easily and above average with
each exposure.
SKIN TYPE V - This individual’s system rarely
burn, tans easily and substantially.
Recommended Exposure Schedule
WEEK 1
1 ST-3RD
TREATMENTS
2 MIN.
2 MIN.
2 MIN.
2 MIN.
WEEK 2
4TH-6TH
TREATMENT
S
5 MIN.
5 MIN.
7 MIN.
7 MIN.
WEEK 3
7TH-10TH
TREATMENTS
8 MIN.
8 MIN.
10 MIN.
10 MIN.
WEEK 4
11TH-15TH
TREATMENTS
10 MIN.
10 MIN.
12 MIN.
12 MIN.
WEEKLY
SUBSEQUEN
T
TREATMENTS
12 MIN.
12 MIN.
12 MIN.
12 MIN.
SKIN TYPE
II - FAIR
III - AVERAGE
IV - BROWN
V - DARK BROWN
MAXIMUM EXPOSURE TIME IS 12 MINUTES.
No two individual skin tones are the same. A tan to one person
may be different to another and treatment length may vary.
Note: Adequate ventilation of the room housing of
the tanning unit is required for proper and
comfortable operation. Air from the room is used
to cool the unit, so be sure nothing obsstructs or
blocks the airflow into or out of the fan and ventilation
openings. Your tanning booth was designed to
operate at an ambient room temperature, during
unit operation of 75 degrees to 85 degrees.
A poorly ventilated room may cause the unit to
become hot and could cause discomfort to the user
and damage the unit. Equally important many facial
makeups have oil bases and should be removed
prior to a session. It is recommended that, following
a tanning session, a skin moisturizer be applied.
This promotes a smoother, more even looking tan.
6
Step 1
Remove floor assembly from carton marked “Top”
The floor of your tanning unit consists of - two (2) parts
A- Base -lower floor
B. Floor -upper floor
Step 2
Position base in desired location. Align floor allowing
a minimum of 63" from back of base to insure
adequate distance to open door of unit properly.
Also, allow a minimum of 18" around the
parameter of the floor for ballast installation and
access from the rear of the unit.
(See Illustration 1)
NOTE: Check to insure all panel attachment
latches are fully open.
(See Illustration 2)
Step 3
Remove panel B front box marked “PLB” and locate
on base. Align slots in bottom plate of panel B with
alignment pins in floor. Attach panel B to base with
the two (2) attachment latches by placing the latch
into slot in booth panel. Press downward on latch
paddle, latch should snap into place securing panel
B to base.
(See Illustration 3)
Step 4
Remove panel A from box marked “PLA” and
locate on base. Align slots in bottom plate of
panel A with the alignment pins in floor. Align
left side of panel A with right side of panel B,
the side rails of both panels should nest together.
Attached panel A to base with the two (2)
attachment latches by placing the latch into
slot in booth panel. Press downward on latch
paddle, latch should snap into place securing
bottom of panel A to base. Attach panel A to
panel B with the upper panel latch located on
the top of panel B by repeating the above l
atching procedure.
(See Illustration 4)
Illustration 4
Illustration 3
Illustration 1
Illustration 2
Assembly Instructions
7
Step 5
Remove panel C from marked “PLC” and locate
on base. Align slots in bottom plate of
panel C with the alignment pins in floor.
Align right side of panel C with left side of
panel B, the side rails of both panels should
nest together. Attach panel C to base with
the two (2) attachment latches by placing
the latch into slot in booth panel. Press
downward on the latch paddle, latch should
snap into place securing bottom of panel C
to base. Attach panel C to panel B with the
upper panel latch, located on the top of panel
B by repeating the above latching procedure.
(See Illustration 5)
Illustration 5
Step 6
Remove Panel D from box marked “PLD” and
stand panel upright into position. Place washer
over both top and bottom hinge pins. Align
hinge pins in door with hinges in Panel C, and
allow hinge pins to drop into hinges. The door
panel will re-hang on booth body.
(See Illustration 6)
Step 7
Locate floor and place over base.
Attach floor to base with safety rails.
By placing safety rail on threaded studs
protruding through floor. Tighten rails securely.
(See Illustration 7 )
Step 8
Remove top fan panel from box marked “Top”.
Place top fan panel on tanning unit. Attach
top fan panel to tanning unit using the nine
(9) provided 5/16" - 18 x 1 bolts.
(See Illustration 8)
Assembly Instructions
Illustration 7
Illustration 6
8
Step 9
Locate lamp harness and place on top.
To connect lamp harness to panel A terminate
harness to panel A cord 2 align plug and twist
clock wise until locked. Repeat procedure for
panel B cord 2, panel C cord 2 and door panel
cord.
(See Illustration 9)
Step 10
Locate panel A power cord 1 and connect with
panel A cord 1. To terminate panel A cord 1 to
power cord 1 align plug and twist clock wise until
locked. Repeat procedure for panel B cord 1 and
panel C cord 1.
(See Illustration 9)
Step 11
Locate top fan wires and connect to fan power wires
from Panel A to fan. Match connector to the corresponding
color.
(See Illustration 10)
Step 12
Remove plastic top cover from box and connenct the
three (3) 4 conductor phone cables from Panel A
to timer jack plate in plastic top cover. Secure top
cover to top of unit using four (4) 1/4 - 20 X 3/4 bolts.
(See Illustration 8)
Step 13
Remove one (1) ballast panel from box marked
“ballast”. To install ballast panel slide tabs of
ballast panel into slots at bottom of ballast
access. To avoid later service problems please
note that the interior harness is not trapped
between ballast panel inner booth structure.
Attach ballast panel to inner booth structure
with two (2) of the provided # 6 x 3/8 philips
screws tighten securely.
(See Illustration 10)
Step 14
Connect ballast to lamps by terminating the MTE/LK
male harness plug with the female ballast plug.
Repeat procedure for remaining ballast panels.
(Refer to Pages 25-27)
Assembly Instructions
Illustration 8
Illustration 9
Illustration 10
9
Step 15
Attach ballast access covers with #6 x 3/8 philips
screws and snap caps.
(See Illustration 11)
Step 16
There are two terminal blocks located on the ballast tray
installed in each panel. Each panel has a relay with four
power wires (2 Black & 2 Red) with quick-slide connectors
that are to be connected to the mentioned terminal blocks
at the time of installation. Install the wires on the terminal
block as shown with the corresponding colors. If the
wires from the relay are improperly installed on the wrong
terminals, certain lamps in the tanning unit will not illuminate.
(Refer to Schematic page 24, for more details.)
Step 17
Contact a local licensed electrician to connect electrical supply to unit. Your tanning booth requires a
120V/225V three phase, 50 amp service or 120V/225V single phase 80 amp 4 wire service. Use of a voltage
source below 215VAC or above 230VAC may prevent proper operation of the booth and could cause damage
and void the warranty.
NOTE: This unit is factory pre-wired for three phase operation. See page 31 for single phase
conversion instructions and wire gage.
Assembly Instructions
Illustration 11
Table des matières
Autres manuels SunDash Lit de bronzage
